Amantii SYM Series Assembly instructions

Fix your Fireplace
SYM Series

SAFETY FIRST
TO AVOID ANY ELECTRICAL SHOCK OR POTENTIAL
DAMAGE TO THE UNIT REMEMBER TO TURN THE
POWER OFF TO THE UNIT BEFORE ATTEMPTING TO
REMOVE OR INSTALL ANY PARTS.

Content
•How to replace LED light
•How to replace flicker motor
•How to replace heating element
•How to replace the PCB board
•How to replace the signal receiver
•How to replace the canopy light

Replace LED light
Step 1
Replace ember bed LED light
Remove Trim -remove the screws circled in red so the trim
can be removed. Screws will be needed to reinstall the trim.

Magnetic stone
Trim
Please note that there are magnetic stones on the bottom of the trim that
attaches the trim to the bottom face.

Step 2 After the trim has been removed, the front glass panel can be removed.
Front glass panel

Step 3
Remove steel side panels. The steel side panels hold the log in place. Remove
the 4 screws circled in red to remove the side panels. Screws will be reused to
reattach the steel side panels.
The steel panels

Step 4
The log can now be removed from the unit once the side panels are out. Remove
the log be lifting one end of the log upwards as seen in the picture below.

Step 5
After the steel panels have been removed, the ember bed glass panel can
carefully be removed by rising one end up first and then out. The ember bed LED
strips are located below it. Remember this is a piece of glass and can break if not
handled with care.

Step 6
The LED strips are held in place with screws and are connected to the other
strips or to the end using a molex connector. Unscrew the screws of the failed
LED strip and unplug the molex connector to replace it with a new one.
Unscrew
Unplug

Replace Flame LED light
Follow STEP 1 to 5 in Replace Ember Bed LED light, you come to here.
Step 1 Remove the screws circled in red to remove the steel bar fixing the
back glass to the unit. Remove steel bar from unit. Glass can now be
removed from the unit.

Zoomed View Zoomed View
Step 2
Remove flame effect steel panel. To remove the panel,
remove the 2 screws shown circled in red on each side
of the unit. Remove the panel and set aside.

After the flame effect steel panel has been removed, you come to here.
Horizontal view
Bird’s eye view
LED strips for flame
effect lie here

HOOK
MOLEX CONNECTOR
Remove flame effect steel panel. To remove the panel, remove
the 2 screws shown circled in red on each side of the unit. Remove
the panel and set aside.
Step 3

Follow STEP 1 to 5 in Replace Ember Bed LED light, you come to here.
Step 1 Remove the back glass to expose location of the Flicker motor.
Unscrew the screws circled in red to remove the steel bar that secures
the back glass. Remove steal bar and set aside. The back glass can
now be removed and set aside.
.
Replace flicker motor

Zoomed View Zoomed View
Step 2
Remove flame effect steel panel. To remove the panel,
remove the 2 screws shown circled in red on each side
of the unit. Remove the panel and set aside.

After the flame effect steel panel’s been removed, you can see the flame motor
on the left end.

Step 1 Step 2 Step 3
Unscrew the clamp
that secures the
flicker rod onto the
motor. Remove the
rod by carefully
pulling it off of the
motor
Unscrew the 2
screws circled in red
to remove the motor
from the fireplace.
The motor is
connected using
spade connectors.
Carefully disconnect
the motor and replace
Steps to remove Flicker Motor

Follow STEP 1 to 4 in Replace Ember Bed LED light.
Step 1 Remove the back glass to expose the flame effect steel panel.
Unscrew the screws circled in red to remove the steel bar that secures
the back glass. Remove steal bar and set aside. The back glass can
now be removed and set aside.
Replace the heating element

Zoomed View Zoomed View
Step 2
Remove flame effect steel panel. To remove the panel,
remove the 2 screws shown circled in red on each side
of the unit. Remove the panel and set aside.