Amino Maxi ATV User manual

1TV input source select
2TV/AUX power/standby
3Color navigation
4Skip Reverse
5Set-top box (STB) PVR transport
6Home
7Navigation and OK
8Back
9Volume up and down
10 Channel select and text entry
11 Teletext
12 Option
13 Infra-red (IR) window
14 Microphone
15 STB power/standby
16 Replay
17 Skip Forward
18 Electronic Program Guide
19 Info
20 Voice control
This button may have or icon
21 Channel/Page up and down
22 Mute
23 Subtitles/closed captions
24 Radio
25 Low battery warning LED
Note: Some functionality (e.g. PVR) may not be available on specic
models of set-top box (STB), also functionality may vary with the TV
service delivered by your service provider.
Remote control layout
Battery information
Do not mix dierent types of battery or old and new
batteries.
Do not use rechargeable batteries.
Remove the batteries from the remote control if you
are not going to use it for several weeks, to avoid the
risk of leakage.
Please respect your environment and any local
regulations and dispose of old batteries in a
responsible manner.
Do not attempt to recharge the batteries.
Immediately remove any leaking batteries.
Take care when handling leaking batteries as they
may cause burns to the skin or eyes, or other physical
injuries.
Operation
When you press a key, point the remote control towards
the front of the STB to ensure correct operation.
Do not cover the infra-red (IR) window at the front of
the remote control and at the front of the STB.
When a key is pressed, either the STB key will ash or,
if a TV brand has been entered, the TV/AUX POWER
key will ash, depending on which product is being
controlled by the remote control.
If you press a key for more than 30 seconds the remote
control will stop transmitting commands to preserve
battery life.
Maxi ATV Remote Control User Guide
+
+
–
–
1. Inserting batteries
1. Slide the battery housing cover downwards to remove it.
2. Insert two AAA batteries with the + and - ends
positioned as shown.
3. Ret the battery housing cover.

99-709952-08SC Rev. 01-02
Programming the Matterhorn Remote
1. Controlling the Set-Top Box (STB)
Your remote control has to be ‘paired’ to the STB to control it.
A remote control can only pair with one STB at a time.
Note: please ensure the Set-top box is powered on rst
1. Press and hold OPTION and OK for at least three seconds until the STB
key ashes to acknowledge. The timeout for pairing is 60 seconds.
If pairing is successful: STB-LED will provide a conrmation blink.
If pairing is unsuccessful: the TV/AUX POWER key gives a long ash
to indicate an error (the STB may indicate this change, depending
on the software running on the Set-top Box).
During pairing no remote control keys will work except the BACK key.
2. Controlling the TV – Auto Search
Note: this process may take several minutes to nd your TV code.
Make sure your TV is turned on. The STB does not need to be turned
on for the brand search.
1. Press 1 and 3 together for at least three seconds until the TV/AUX
POWER key ashes twice and remains on.
• If successful: the STB key will ash once and remain on.
• If unsuccessful: the TV/AUX POWER key will give a long ash and
the remote control will revert to normal operation.
2. Press and continue to hold the TV button.
• The remote will now start searching for codes to control your
TV. A new code is tried every 1.5 seconds.
3. Once the TV turns o, release the TV button. Releasing the
button conrms the code.
• Try the Volume+/-, MUTE, TV-INPUT buttons to ensure they are
working.
4. If working press the BACK key.
5. If not working, press and hold the TV button again to continue the
search. When the TV power state changes, release the button and
try steps 4&5 again.
If Search Is unsuccessful, you can also try “Manually input TV
Manufacturer’s Code” in the “Troubleshooting and Advanced
Features” section.
Troubleshooting and Advanced Features
Control The TV - Manually Input TV
Manufacturer’s Code
The TV/AUX POWER, TV INPUT, VOL+, VOL- and MUTE keys of the
remote control can be programmed to operate your TV. To do this,
your remote control must rst learn the ‘brand code’ of your TV. By
default, the remote control is programmed with the most common
brand code 0618 (Samsung).
1. Press <<2 + 6>> simultaneously for 3 seconds. During the initial 3
seconds, the LEDs will remain o, then the TV-LED will provide a
conrmation blink and remain on.
2. Enter a 4 digit code set ID code from TV Brand Codes for Maxi
(Find the 4-digit brand code for your TV BRAND CODES at https://
www.amino.tv/resources/)
• When a digit is pressed, the TV-LED gives a short inverse blink.
Any other key (Non-digit key) press will result in an invalid
sequence. In this case, the RCU will give an error blink (Blink
rapidly 4 times) and return to user mode.
• If entered sequence of digits is valid, TV-LED will execute a con-
rmation blink, and then goes back to user mode.
• If entered sequence of digits is invalid, TV-LED will execute an
error blink, and then goes back to user mode.
If you change your TV to a dierent brand the remote control will
require re-programming. Repeat this brand search procedure with
the brand code for your new TV.
5. IR Learning mode
The Maxi ATV remote control can learn a key function from another
‘source’ remote control. This may be useful when the Auto-Search
or Manual programming steps fail.
1. Choose your ‘target key’ on the remote control. It must be one
of the following keys: TV/AUX POWER / TV INPUT / VOL+ / VOL- /
MUTE. This key will learn a function from the source remote
control.
2. Press 4 and 6 for at least three seconds. The TV/AUX POWER key
will ash twice and remain on.
3. Press your target key within 30 seconds:
• if valid, the TV/AUX POWER key will give a conrmation ash and
remain on.
• if invalid, or you do not press within 30 seconds, the TV/AUX
POWER key will give an error blink and return to user mode.
4. Hold the Maxi ATV remote control 3 - 6 cm from the source
remote control with the IR windows facing each other, then press
your target key on the source remote control (e.g. if your target
key on the Maxi ATV remote control is mute, press mute on the
source remote control).
5. If the IR signal is received correctly, the TV/AUX POWER key will
turn o and the remote control will return to normal mode (note:
this can overwrite a previously learned code).
6. If the IR signal is not received correctly, or is received after 30
seconds, the Maxi ATV remote control will not store the code
from the source remote control: it will give an error blink and
return to user mode.
7. If the Back key is pressed on the remote control while it is waiting
for an IR signal, the TV/AUX POWER key will give an error blink
return to user mode. (If the target key is pressed, any learned
code on it is cleared.)
8. To clear the target key, press 4 and 6 for at least three seconds.
The TV/AUX POWER key will ash twice and remain on. Then press
your <target key> twice. The TV/AUX POWER key will ash to
conrm the target key is cleared.
6. Factory reset
Factory reset will return the remote control to it’s factory settings.
1. Press 1 and 6 for at least three seconds until the TV/AUX POWER
key ashes twice then stays on.
2. Enter the key sequence 9 8 1. After completing the sequence the
STB key will ash twice. The TV settings are now deleted from
the remote control and it returns to factory settings: IR mode,
Samsung brand code (0618) and unpaired.