Amino A140 User manual

Read these instructions carefully and keep for future reference. Note all
warnings.
The product contains no user-serviceable parts. Refer all servicing to qualified
service personnel.
Handle the product with care and do not attempt to dismantle the product.
Do not expose the product or its accessories to any liquids, rain or moisture.
Do not locate the product near a heat source and do not block ventilation
holes: the product will become warm during operation. Allow at least 10 cm
(4”) around the product for air circulation.
Do not locate the product where it may be subject to physical shock, vibration
or where the product may fall over.
Do not place the product on soft furnishings or carpets.
Only use the power supply provided by the manufacturer. The use of any
other type of power supply may invalidate any approval or warranty applying
to the product and may be dangerous. If the power supply does not match
your local system, contact your product supplier.
Protect the power supply cord from damage.
The disconnect device is the power supply cord. Removing the power supply
cord from the mains supply isolates the product from the mains.
Disconnect the product from the mains supply if left unused for long periods
of time or during electrical storms.
Disconnect the product before cleaning, and use a dry cloth only.
Only use attachments and accessories specified by the manufacturer.
The product is for indoor use only.
Power/Activity LED:
Green = on.
Green flashing = IR command received.
Red = standby.
1.
Warning! Before connecting or disconnecting any cable switch
off all system devices (TV, A/V Amplifier, etc) and disconnect
from the mains electrical supply.
The A140 provides three options for connecting audio and
video to your TV:
HDMI (recommended): best quality. Connect an HDMI cable
to the HDMI output of the A140 and to the HDMI input of
your TV.
Analogue A/V: good quality. SD only, composite or
component with analogue audio left/right (depending on
supplied A/V lead).
RF: moderate quality. Connect the RF cable directly to a TV
tuner input. DO NOT connect the RF output to any cable
distribution network, satellite dish or antennae. A TV terrestrial
antenna or cable connection may only be made to the RF
input to provide loop-through functionality to the TV via the
STB. Connections to a cable distribution system must be made
through a galvanic isolator.
Analogue A/V output.
RF modulator output.
HDMI output.
RF antenna input.
DC power input.
USB port.
Service button. No function in normal use. Only use under
guidance from your service provider.
Ethernet port.
S/PDIF optical output.
1.
2.
3.
4.
5.
6.
7.
8.
9.
The A140 is supplied with the correct power adapter for your
local system. The package may also contain optional accessories
shown below, depending on your service provider.
The product is protected with a clear plastic film. This should be
removed before use.
A140 User Guide
1. Overview of the A140 2. Connecting the A140 to a TV
Important - Safety instructions
Contents
Optional accessories
Remote control
and batteries 10 way mini-DIN to
SCART cable
HDMI cable
10 way mini-DIN to
3 x RCA or 6 x RCA cable
Ethernet cable

Connect an optical S/PDIF cable to the S/PDIF optical output of
the A140 and the S/PDIF optical input of an A/V amplifier or home
cinema system.
The following paragraphs describe requirements and conformity:
4. Connecting the A140 to the power supply
Warning! The A140 must only be used with the supplied power
adapter.
Connect the power adapter to the DC power input, then connect
the power adapter to the mains supply. The power adapter
provided will be specific to your region. Ensure you have the
correct power adapter for your region. If you are unsure, contact
your service provider.
3. Connecting the A140 to an A/V amplifier
511-846-00-12 AM-002930-DS v10
Support and regulatory information
Product disposal information - EU only
FCC statement
Operating information
Amino products are labelled in accordance with the WEEE Directive
and therefore should not be disposed of with other household or
commercial waste. For residential users: please remove any batteries
and dispose of them and the product in accordance with your local
authority’s recycling processes. For further information please contact your local
authority or the retailer where the product was purchased.
For business users: business users should contact their supplier and check the
terms and conditions of the purchase contract and ensure that the product is not
mixed with other commercial waste for disposal.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received, including interference that
may cause undesired operation of the device.
IMPORTANT NOTE:
RF exposure warning statement:
1) This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
2) This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20 centimetres between the radiator and your body.
European Approvals
2014/35/EU (Low voltage Directive)
2011/65/EU (RoHS Directive)
2012/19/EU (WEEE Directive)
2014/30/EU (EMC Directive)
The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and
other countries.
Manufactured under licence from Dolby Laboratories. Dolby and the double D
symbol are trademarks of Dolby Laboratories.
For support and further regulatory information about this product go to:
https://www.aminocom.com/support
Manufacturer/importer: Amino Communications Ltd, Buckingway Business
Park, Anderson Road, Swavesey, Cambridge, CB24 4UQ, United Kingdom.
Conformity
60950-1 2nd Edition
CAN/CSA-C22.2 No 60950-1-07
Operating temperature: 5 °C to 40 °C (40 °F to 104 °F)