Amino Kamai 7B User manual

Read these instructions carefully and keep for future reference. Note all
warnings.
The product contains no user-serviceable parts. Refer all servicing to qualified
service personnel.
Handle the product with care and do not attempt to dismantle the product.
Do not expose the product or its accessories to any liquids, rain or moisture.
Do not locate the product near a heat source and do not block ventilation
holes: the product will become warm during operation. Allow at least 10 cm
(4”) around the product for air circulation.
Do not locate the product where it may be subject to physical shock, vibration
or where the product may fall over.
Do not place the product on soft furnishings or carpets.
Only use the power supply provided by the manufacturer. The use of any
other type of power supply may invalidate any approval or warranty applying
to the product and may be dangerous. If the power supply does not match
your local system, contact your product supplier.
Protect the power supply cord from damage.
The disconnect device is the power supply cord. Removing the power supply
cord from the mains supply isolates the product from the mains.
Disconnect the product from the mains supply if left unused for long periods
of time or during electrical storms.
Disconnect the product before cleaning, and use a dry cloth only.
Only use attachments and accessories specified by the manufacturer.
The product is for indoor use only.
Power/Activity LED:
Blue = on.
Blue flashing = IR command received.
Red = standby.
Wi-Fi signal strength indicator.
1.
2.
Warning! Before connecting or disconnecting any cable switch
off all system devices (TV, A/V Amplifier, etc) and disconnect
from the mains electrical supply. The Kamai 7B provides options
for connecting audio and video to your TV:
HDMI (recommended): best quality. Connect an HDMI cable
to the HDMI output of the Kamai 7B and to the HDMI input of
your TV.
Analogue A/V: good quality. Composite video (SD only) with
analogue audio left/right. Connect the 3.5 mm jack to the A/V
output on the Kamai 7B and connect the yellow RCA plug to the
yellow video port on your TV. Connect the red and white RCA
plugs to the red and white audio ports on your TV.
The Kamai 7B is supplied with the correct power adapter for your
local system. The package may also contain optional accessories
shown below, depending on your service provider.
The Kamai 7B is protected with a clear plastic film. This should be
removed before use.
RF antenna or cable input
(optional).
Analogue A/V output.
Ethernet port.
HDMI output.
USB port.
S/PDIF optical output.
DC power in 12 V 2 A.
WPS button.
1.
2.
3.
4.
5.
6.
7.
8.
On/off switch.
Reset button. No function
in normal use. Only use
under guidance from your
service provider.
Smart card port for users
with SIM format smart cards
(optional).
9.
10.
11.
1. Overview of the Kamai 7B 2. Connecting the Kamai 7B to a TV
Important - Safety instructions
Contents
Optional accessories
Kamai 7B User Guide
Internal single band Wi-Fi is a feature of the Kamai 7B. Please
contact your service provider for detailed instructions about
configuring your wireless network.
Connecting via Wi-Fi
Remote control
and batteries
HDMI cable
3.5 mm jack to
3 x RCA cable
Ethernet cable

Connect an optical S/PDIF cable to the S/PDIF optical output
of the Kamai 7B and to the S/PDIF optical input of your A/V
amplifier or home cinema system.
Warning! The Kamai 7B must only be used with the supplied
power adapter.
Connect the power adapter to the DC power input of the Kamai
7B, then connect the power adapter to the mains supply. The
power adapter provided will be specific to your region. Ensure
you have the correct power adapter for your region. If you are
unsure, contact your service provider.
99-708804-83 Rev. 01-00 AM-011294-DS v1
4. Connecting the Kamai 7B to the power supply
3. Connecting the Kamai 7B to an A/V amplifier Support and regulatory information
Operating information
Declaration of Conformity
Hereby, Amino Communications Ltd. declares that the radio equipment type
IP Digital set-top box
is in compliance with Directive 2014/53/EU.
The full text of the EU Declaration of Conformity is available at the
following internet address: https://www.aminocom.com/support
European Approvals
2014/53/EU (RE Directive)
2011/65/EU (RoHS Directive)
2012/19/EU (WEEE Directive)
The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.
Manufactured under licence from Dolby Laboratories. Dolby and
the double D symbol are trademarks of Dolby Laboratories.
This product incorporates copyright protection technology that is protected by
U.S. patents and other intellectual property rights of Rovi Corporation. Reverse
engineering or disassembly is prohibited.
The country code selection feature is disabled for products marketed to the
US/Canada.
For support and further regulatory information about this product go to:
https://www.aminocom.com/support
Manufacturer/importer: Amino Communications Ltd, Buckingway Business
Park, Anderson Road, Swavesey, Cambridge, CB24 4UQ, United Kingdom.
Operating temperature: 5 °C to 40 °C (40 °F to 104 °F)
Frequency bands and maximum powers:
WLAN Bluetooth
5.18~5.24 GHz: EIRP < 23 dBm
5.26~5.32 GHz: EIRP < 23 dBm
5.50~5.70 GHz: EIRP < 23 dBm
BT-EDR: EIRP < 4 dBm
BT-LE: EIRP < 2 dBm
This device complies with ISED’s licence-exempt RSSs. Operation is subject to
the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received, including interference
that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes:
1) le dispositif ne doit pas produire de brouillage préjudiciable, et
2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage
susceptible de provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20 cm between the radiator and your body.
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements
ISED établies pour un environnement non contrôlé. Cet équipement doit être
installé et utilisé avec un minimum de 20 cm de distance entre la source de
rayonnement et votre corps.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received, including interference that
may cause undesired operation of the device.
IMPORTANT NOTE:
RF exposure warning statement:
1) This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
2) This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20 centimetres between the radiator and your body.
FCC statement
Industry Canada statement
Conformity
60065:2014
CAN/CSA-C22.2 No. 60065-16
Product disposal information - EU only
Amino products are labelled in accordance with the WEEE Directive
and therefore should not be disposed of with other household or
commercial waste. For residential users: please remove any batteries
and dispose of them and the product in accordance with your local
authority’s recycling processes. For further information please contact your
local authority or the retailer where the product was purchased.
For business users: business users should contact their supplier and check the
terms and conditions of the purchase contract and ensure that the product is
not mixed with other commercial waste for disposal.
For FCC ID: XVG500144BC00, it supports 5G WiFi only without the other RF Tx function.