Amino Kamai 7XM User manual

Important - Safety instructions
Read these instructions carefully and keep for future reference. Note all warnings.
The product contains no user-serviceable parts. Refer all servicing to qualified
service personnel.
Handle the product with care and do not attempt to dismantle the product.
Do not expose the product or its accessories to any liquids, rain or moisture.
Do not locate the product near a heat source and do not block ventilation holes:
the product will become warm during operation. Allow at least 10 cm (4”) around
the product for air circulation.
Do not locate the product where it may be subject to physical shock, vibration or
where the product may fall over.
Do not place the product on soft furnishings or carpets.
Only use the power supply provided by the manufacturer. The use of any other
type of power supply may invalidate any approval or warranty applying to the
product and may be dangerous. If the power supply does not match your local
system, contact your product supplier.
Protect the power supply cord from damage.
The disconnect device is the power supply cord. Removing the power supply cord
from the mains supply isolates the product from the mains.
Disconnect the product from the mains supply if left unused for long periods of
time or during electrical storms.
Disconnect the product before cleaning, and use a dry cloth only.
Only use attachments and accessories specified by the manufacturer.
The product is for indoor use only.
1. Power/Activity LED:
Blue = on.
Blue flashing = IR command received / Kamai 7XM starting up.
Red = standby.
Warning! Before connecting or disconnecting any cable switch
off all system devices (TV, A/V Amplifier, etc) and disconnect
from the mains electrical supply. The Kamai 7XM provides options
for connecting audio and video to your TV:
HDMI (recommended): best quality. Connect a HDMI cable to the
HDMI output of Kamai 7XM and to the HDMI input of your TV.
Analogue A/V: good quality. Composite video (SD only) with
analogue audio left/right. Connect the 3.5 mm jack to the A/V
OUT port of Kamai 7XM and connect the yellow RCA plug to the
yellow video port on your TV. Connect the red and white RCA
plugs to the red and white audio ports on your TV.
Connecting to a Network
Select from one of the following networking options.
Option 1
Connect an Ethernet cable from Kamai to a
cable/DSL modem or Network Router.
(Router not included, cable is optional and may not be included)
Option 2
Connect your Kamai to MoCA Network.
1. MoCA cable input.
2. Ethernet port.
3. Analog A/V output.
4. S/PDIF optical output.
5. HDMI output.
6. USB port.
7. DC power input 12 V 2 A.
8. Reset button. No function in normal use.
Only use under guidance from your service provider.
Contents
The Kamai 7XM is supplied with the correct power adapter for your
local system. The package may also contain optional accessories
shown below, depending on your service provider.
The Kamai 7XM is protected with a clear plastic film. This should be
removed before use.
1 2 3 4 5 6 7 8
HDMI
Analogue
A/V
1. Overview of the Kamai 7XM 2. Connecting the Kamai 7XM to a TV
Optional accessories
Kamai 7XM User Guide
Remote control
and batteries
HDMI cable
3.5 mm jack to
3 x RCA cable
Ethernet cable

Connect an optical S/PDIF cable to the S/PDIF optical output of
Kamai 7XM and to the S/PDIF optical input of your A/V amplifier
or home cinema system.
Warning! The Kamai 7XM must only be used with the supplied
power adapter.
Connect the power adapter to the DC power input of Kamai 7XM,
then connect the power adapter to the mains supply. The power
adapter provided will be specific to your region. Ensure you have
the correct power adapter for your region. If you are unsure,
contact your service provider.
99-708904-62 Rev. 01-00 AM-011261-DS v1
4. Connecting Kamai 7XM to power supply
3. Connecting Kamai 7XM to an A/V amplifier
FCC statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that
may cause undesired operation of the device.
IMPORTANT NOTE:
RF exposure warning statement:
1. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
2. This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20 centimetres between the radiator and your body.
Product disposal information - EU only
Amino products are labelled in accordance with the WEEE Directive and
therefore should not be disposed of with other household or commercial
waste. For residential users: please remove any batteries and dispose of
them and the product in accordance with your local authority’s recycling
processes. For further information please contact your local authority or
the retailer where the product was purchased.
For business users: business users should contact their supplier and check the
terms and conditions of the purchase contract and ensure that the product is not
mixed with other commercial waste for disposal.
Industry Canada statement
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the
following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that
may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
1. le dispositif ne doit pas produire de brouillage préjudiciable, et
2. ce dispositif doit accepter tout brouillage reçu, y compris un brouillage
susceptible de provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator and your body.
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements ISED
établies pour un environnement non contrôlé. Cet équipement doit être installé
et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement
et votre corps.
Operating information
Operating temperature: 5 °C to 40 °C (40 °F to 104 °F)
Frequency bands and maximum powers:
Bluetooth
BT-EDR: EIRP < 4 dBm
BT-LE: EIRP < 2 dBm
Hereby, Amino Communications Ltd. declares that the radio equipment type
IP Digital set-top box
is in compliance with Directive 2014/53/EU.
The full text of the EU Declaration of Conformity is available at the
following internet address: www.aminocom.com/support
Support and regulatory information
Approvals
2014/53/EU (RED Directive)
2011/65/EU (RoHS Directive)
2012/19/EU (WEEE Directive)
FCC Part 15B:2015+ANSI C63.4:2014
FCC Part 15C (15.247)
Manufactured under licence from Dolby Laboratories. Dolby, Dolby Audio,
and the double-D symbol are trademarks of Dolby Laboratories.
This product incorporates copyright protection technology that is protected by
U.S. patents and other intellectual property rights of Rovi Corporation. Reverse
engineering or disassembly is prohibited.
The country code selection feature is disabled for products marketed to the US/Canada.
For support and further regulatory information about this product go to:
www.aminocom.com/support
Manufacturer/importer: Amino Communications Ltd, 1010 Cambourne Business
Park, Cambourne, Cambridge, CB23 6DP, United Kingdom.
Declaration of Conformity
Conformity
IEC 62368-1:2014
CAN/CSA-C22.2 No. 62368-1-14