AMP Lighting AxialPro APL-3025-4-B-BZ Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP® AxialPro Bollard
APL-3025-4-B-BZ

AMP®AxialPro Bollard
APL-3025-4-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
Important Safety Instructions
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS

[email protected] • 813.978.3900
Product Dimensions
–3–
Package Contents
A. (1) Fixture Body
B. (1) Coupler
C. (1) Hat
D. (1) Finial
22.4”
5.9”
6.45”

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
2
1
AMP®AxialPro Bollard
APL-3025-4-B-BZ
Install Fixture Hat
Install Stake
Screw the coupler onto the top
center of the xture body and
hand tighten until snug.
Secure the xture hat onto the
coupler with the nial and hand
tighten until snug.
Finial
Fixture Hat
Fixture Body
Coupler
Determine the desired location
for mounting the stake mount.
Hammer the stake into the
ground until ange of stake
is ush to grade. To avoid
damage to the stake, place a
board on top of the stake while
hammering.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.
Board
Ground
Soil
Stake

[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
3
AMP®AxialPro Bollard
APL-3025-4-B-BZ
Install Fixture Body to Stake
Pass the xture wire through
the center hole of the stake.
Thread the xture body onto
the stake and hand tighten until
snug.
Fixture Body
Fixture Wire
Ground
Soil
Stake

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
4
AMP®AxialPro Bollard
APL-3025-4-B-BZ
Wire Connections
Strip both leads from the xture body. Using two wire connectors (sold
separately) connect the leads from the xture body to the main supply
cable leads.
Pigtail
Main Supply Cable
Supply Wire from
Fixture Body
Wire Connectors

–6––6–
[email protected] • 813.978.3900
–7–

IS-APL-3025-4-B-BZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2019, AMP®Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com