AMP Lighting HydraPro AWL-5005-B-BZ Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP® HydraPro MR11 Well Light (Lamp Ready)
AWL-5005-B-BZ

AMP®HydraPro MR11 Well Light (Lamp Ready)
AWL-5005-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
Important Safety Instructions
!
This xture is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation, oper-
ation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing
this xture.
2. Warning: this xture is not intended to be installed within 10 feet [3
meters] of a pool, spa or fountain.
3. This xture is intended to be used only with a power supply (trans-
former) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm)
in order to connect to the main low voltage cable.
5. Wiring connections must be made with UL Listed wire connectors that
are suitable for the application.
6. Position the wire connector so that it is located within 6 inches (15.2
cm) from a building structure, a luminaire, or tting.
LIGHTED LAMP IS HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.

[email protected] • 813.978.3900
Product Dimensions
–3–
Package Contents
Parts Required (sold separately)
A. (1) Fixture Body
B. (1) Holder
C. (1) PVC tube
A. (1) MR11 Lamp
4.15”
3”
2.8”
5.8”

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
2
1
AMP®HydraPro MR11 Well Light (Lamp Ready)
AWL-5005-B-BZ
Remove Faceplate
Faceplate
Screw
Fixture Body
Use a screwdriver to loosen the
screws on the faceplate and
remove the lens from the xture
body.
Install Lamp
Socket
MR11 Lamp
Insert the lamp with the correct watt-
age and type marked on the xture
label and push rmly into place.
CAUTION: Do not exceed maximum
wattage marked on xture label.
3
Install Faceplate
Faceplate
Screw
Fixture Body
Place the lens and the faceplate
back onto the xture body and
secure the removed screws in a
star pattern using a screwdriver.
Tighten until snug.

[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
4
5
AMP®HydraPro MR11 Well Light (Lamp Ready)
AWL-5005-B-BZ
Dig Hole
Hole
Soil
3”
3”
3”
PVC Tube Prepare a hole in the
ground. Make sure there are
approximately 3” spaces
surrounding the PVC tube for
pea gravel or sand.
Wire Connection
Holder
Fixture
Body
Wire Connector
Main Supply Cable
Fixture Supply Cable
Soil
PVC Tube
Pass the xture supply cable
through the holder and the
PVC tube. Place the holder
onto the PVC tube, then place
the xture body into the
holder properly.
Strip both leads from the
xture supply cable and the
main supply cable. Using
two wire connectors (sold
separately), connect the leads
from the xture supply cable
to the main supply cable.

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
6
AMP®HydraPro MR11 Well Light (Lamp Ready)
AWL-5005-B-BZ
Fill Hole
Install the PVC tube with the
xture in the hole and ll the
hole with pea gravel or sand.
Pea Gravel
or Sand
Soil
PVC Tube
with Fixture
Repeat step 1 - step 3 to remove the faceplate to expose the lamp and
replace it with the correct wattage and type marked on the xture label.
Then, reinstall the faceplate.
IMPORTANT: Lamps must be protected from moisture and dust at all
times. Always reinstall the faceplate when removed.
Install/Replace Lamp

–6––6–
[email protected] • 813.978.3900
–7–
Install/Replace Faceplate
7
Remove Faceplate
Use a screwdriver to loosen the
screws on the faceplate and
remove the lens from the xture
body.
Faceplate
Lens
Screw
Fixture Body
8
Replace Faceplate
Place the lens and faceplate onto
the xture body and secure with
previously removed screws in a
star pattern. Hand tighten until
snug with a screwdriver.
Faceplate
Lens
Fixture Body
Option 1 Option 2
Faceplate Replacement Options
Option 3 Option 4

IS-AWL-5005-B-BZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2020, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com