AMQ ACTIV-Pro3 User manual

ACTIV-Pro3 installation guide

ACTIV-PRO3 HEIGHT ADJUSTABLE BASE INSTALLATION GUIDE | 2 amqsolutions.com
COMPONENTS
Hardware
foot
x 2
cantilever
x 2
center leg
bracket x 1
end leg
x 2
center leg
x 1
M10
x 8
M6
(special)
x 8
wood
screw
x 23
M6
x 12
handset
screw
x 2
cable clips
x 12
8mm 5mm
allen keys
4mm
screw caps
x 8
stretcher bar
end x 2
stretcher bar
x 4
frame
BL x 1
frame
BR x 1
frame
FL x 1
frame
FR x 1
controller
cable
x 2
power
cable
handset x 1
power box
x 1

ACTIV-PRO3 HEIGHT ADJUSTABLE BASE INSTALLATION GUIDE | 3 amqsolutions.com
PHASE 1 | Leg Attachment
Step 1
Identify center leg.
Step 2
Assemble center leg to center bracket with M6
screws.
21
Front Right, Back
Right, Front Left
and Back Left are
indicated on Center
Bracket with the
initials FR, BR, FL
and BL

ACTIV-PRO3 HEIGHT ADJUSTABLE BASE INSTALLATION GUIDE | 4 amqsolutions.com
PHASE 2 | Attaching Stretcher Bar
1
BL BR
FL FR
Step 1
Match up frames to center bracket, lining up the holes
to the degree that you are setting (90° or 120°). Screw
in with M6 screws.
1
Note limit of stretch length and assemble base within that limitation.
maximum mounting distance

ACTIV-PRO3 HEIGHT ADJUSTABLE BASE INSTALLATION GUIDE | 5 amqsolutions.com
PHASE 2 | Attaching Stretcher Bar
Step 2
Assemble stretcher bars into the frames.
Step 3
Complete connecting the stretcher bars and
stretcher bar ends. Assemble end legs to the
stretcher bar ends using M6 (special) screws.
NOTE: Trim caps will be attached in Phase 4.
2
3
*For 48” width worksurfaces, do not install stretcher bars.

ACTIV-PRO3 HEIGHT ADJUSTABLE BASE INSTALLATION GUIDE | 6 amqsolutions.com
PHASE 3 | Attaching Cantilevers & Feet
Step 1
Plug cantilevers into the stretcher bar ends, lining
up holes. Add screws M6 (special). Tighten using
#4 allen key (or a long extension angle-tipped allen
key to expedite the process).
2
2
1
Step 2
Attach feet to legs with M10 screws.
NOTE: Trim caps will be attached in Phase 4.

ACTIV-PRO3 HEIGHT ADJUSTABLE BASE INSTALLATION GUIDE | 7 amqsolutions.com
PHASE 4 | Adjusting Stretcher Bars
Step 1
Adjust stretcher bar to desired length.
Step 2
Tighten 4 factory inset screws to hold desired
length in place.
Step 3
Place caps.
Make sure the screw bracket stays
in the center of the stretcher bars
3
2
1

ACTIV-PRO3 HEIGHT ADJUSTABLE BASE INSTALLATION GUIDE | 8 amqsolutions.com
PHASE 5 | Connecting Worksurface & Power
3
1
2
Step 1
Ensure that the base is properly positioned on the
worksurface. Attach base to the worksurface using
wood screws.
NOTE: The worksurface should be center
aligned with the cantiliver depth and should
have equal amount of overhang on each end.
Step 2
Attach the handset to desired location using
handset screws (count x2).
Step 3
Plug in electrical according to the diagram at
right. Attach cable management clips if using.
Facing
Direction
Handset
Power
Connect each plugs according to the
drawing. Orientate yourself to the table
assembly by facing as user to identify
left and right motor.

ACTIV-PRO3 HEIGHT ADJUSTABLE BASE INSTALLATION GUIDE | 9 amqsolutions.com
PHASE 6 | Program Height Memory Presets
Step 1
To Program Up to 4 Presets: Use the up/down
arrows to find desired height, then press “M”
followed by the number 1, 2, 3 or 4.
Step 2
To Test Programmed Height: Use the up/down
arrows to adjust the table to a height other than the
preset height. Then push and hold the number you
programmed to see if it automatically adjusts to
the height programmed in Step 1. You may need to
hold for 2-3 seconds to activate the base.
NOTE: If it does not adjust to the programmed
height, repeat Step 1 followed by Step 2.
A
M
Q
1
2
3
M
4

Please contact [email protected] if you are
missing any parts, have difficulty with assembly,
or have any product related questions.