AMQ ACTIV-Pro3 User manual

installation guide
ACTIV-Pro3
height adjustable base

ACTIV-Pro3Installation Guide
P2 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Components
end leg x 2 foot x 2
Hard ware
cantilever x 2
handset x 1
controller cable
x 2
wood
screw x 23
handset
screw x 2
power cable
power box x 1
cable clips x 12
M6 x 12 M6 (special) x 8 M10 x 8
screw caps x 8
center leg
bracket x 1
frame
BR x 1
frame
FL x 1
frame
FR x 1
stretcher bar
end x 2
stretcher bar x 4
frame
BL x 1
center leg x 1
allen keys
4mm5mm8mm
Getting Started

ACTIV-Pro3Installation Guide
P3 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Phase 1 Leg Attachment
Identify center leg.
Assemble center leg to center bracket with M6 screws.
1
2
Identify center leg
Assemble center leg to center bracket with M6 screws
1
1
2
2
2
1
Front Right, Back Right, Front
Left and Back Left are indicated
on Center Bracket with the initials
FR, BR, FL and BL

ACTIV-Pro3Installation Guide
P4 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Match up frames to center bracket, lining up the holes to the degree
that you are setting (90oor 120o). Screw in with M6 screws.
Attach stretcher bars to the frames.
Complete connection of stretcher bars and stretcher bar ends.
Attach end legs to the stretcher bar ends using M6 (special) screws.
Note: Trim caps will be attached in Phase 4.
Attaching Stretcher BarPhase 2
1
2
31
Note limit of stretch length and assemble base within that limitation.
maximum mounting distance
Match up frames to center bracket, line up holes to the degree that you are setting, and screw in M6 screws
Assemble stretcher bars into the frames
Complete connecting the stretcher bars and stretcher bar ends
Assemble end legs to the stretcher bar ends using M6(special) screws
1
2
3
1
2
3
1
2
3
*For 48” width worksurfaces, do not install stretcher bars.

ACTIV-Pro3Installation Guide
P5 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Attaching Cantilevers and FeetPhase 3
1
2
Plug cantilevers into the stretcher bar ends, lining up holes. Add screws M6 (special).
Tighten using #4 allen key (or a long extension angle-tipped allen key to expedite the process).
Attach feet to legs with M10 screws.
Note: Trim caps will be attached in Phase 4.
Plug in cantilevers in the stretcher bar ends, line up holes and add screws M6(special)
Tighten using #4 allen key or a long extension angle-tipped allen key to expedite the process
Add trim caps to fill holes
Attach feet to end legs with M10 screws
1
2
3
1
2
3
1
2
2

ACTIV-Pro3Installation Guide
P6 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Adjusting Stretcher BarsPhase 4
1
2
3
Adjust stretcher bar to desired length.
Tighten 4 factory inset screws to hold desired length in place.
Place caps.
Adjust stretcher bars to desired length
Tighten 4 factory inset screws to hold the desired length in place
Make sure the screw bracket stays
in the center of the stretcher bars
1
2
1
2
1
2
3

ACTIV-Pro3Installation Guide
P7 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Facing
Direction
Connect each plugs according to the drawing.
Orientate yourself to the table assembly by
facing as user to identify left and right motor.
Attach the base assembly to the worksurface
Attach the handset to desired location using handset screws (count x 2)
Ensure that the base is properly positioned to the worksurface
Attach the base to the worksurface using wood screws
Plug in electrial according to below drawing and attach cable management clips, if desired
Note : The worksurface should be centeraligned with the cantilever depth
and should have equal amount of overhang on each end
1
2
3
4
3 4
5
1
1
2
3
Ensure that the base is properly positioned on
the worksurface. Attach base to the worksurface
using wood screws.
Note: The worksurface should be center
aligned with the cantiliver depth and should
have equal amount of overhang on each end.
Attach the handset to desired location using
handset screws (count x2)
Plug in electrical according to the diagram at
right. Attach cable management clips if using.
Connecting Worksurface & PowerPhase 5
2
3

ACTIV-Pro3Installation Guide
P8 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Phase 6 Program Height Memory Presets
1
2
To Program Up to 4 Presets: Use the up/down
arrows to find desired height, then press “M”
followed by the number 1, 2, 3 or 4.
To Test Programmed Height: Use the up/down
arrows to adjust the table to a height other
than the preset height. Then push and hold
the number you programmed to see
if it automatically adjusts to the height
programmed in Step 1. You may need to
hold for 2-3 seconds to activate the base.
Note: If it does not adjust to the
programmed height, repeat Step 1
followed by Step 2.
A
M
Q
1
2
3
M
4

915 Walsh Avenue / Santa Clara, CA 95050 [phone] amqsolutions.com
5 Day Open Plan we provide exceptional
experiences with reliable, easy interactions
and successfully fulfilled orders in only 5 days