AMQ ACTIV-Pro User manual

installation guide
ACTIV-Pro
height adjustable base

ACTIV-Pro Installation Guide
P2 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Components
Leg-1&2 x 2 pcs
stretcher bar assembly
with Control box
cantilevers x 2 pcs
Foot x 2 pcs
LED control handset x 1
socket screws
controller cable x 1
M6 x 8 M10 x 8 M5-20mm
x 18
M5-16mm
x 2
screw caps x 8
power cable x 1
allen keys
Hardware
1. Activ Pro Components Layout
4mm5mm8mm
Cable strapsGlides x 4
Getting Started
*Feet, Glides and attachment screws are boxed separately.
*
*
*

ACTIV-Pro Installation Guide
P3 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Phase 1 Preparing for Assembly
Place Stretcher Bar unit upside down on work area.
2. Stretcher bar unit
Place stretcher bar unit upside down
The label will face up when Stretcher Bar
is upside down and ready to begin assembly.
1
Turn Stretcher Bar upside down

ACTIV-Pro Installation Guide
P4 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
3. Stretcher bars and cantilever assembly -1
M6 screws
use 5mm allen key
Attach leg columns with M6 screws
Attaching LegsPhase 2
1Slide leg columns into place and attach with M6 screws.
Match inside holes first and lightly tighten at this point.
Match inside holes first and lightly tighten at this point.

ACTIV-Pro Installation Guide
P5 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Attaching CantileversPhase 3
1
2
4. Stretcher bars and cantilever assembly -2
Insert cantillevers to each ends
use 5mm allen key
M6 screws
Use screw caps
Insert Cantilevers on each end, lifting the leg a bit, if needed,
to ease into a flush fit. Tab into place (fit is snug).
Using M6 screws, tighten all 4 holes lightly. Once level,
go back through and tighten each screw completely.
Place plastic caps over each screw.

ACTIV-Pro Installation Guide
P6 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Feet AssemblyPhase 4
1Attach feet using M10 socket screws. Match all 4
holes first to confirm fit before tightening completely.
5. Feet assembly
Attach both feet using M10 socket screws
M10 screws
use 8mm allen key

ACTIV-Pro Installation Guide
P7 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Phase 5 Adjusting Base Width
6. Stretcher bars length adjustment
Adjust the length of the base to the desireable width
Tighten all inset screws for stability
Use 4mm allen key to tighten
pre-mounted inset screws
Centered screw bracket
1
1
2
2
1
1
2
2
Adjust to desired width. Use #4 allen key to loosen
the factory-inserted screws if not already loose.
Once at correct width – and ensuring that centered
screw brackets are aligned – tighten all inset screws.

ACTIV-Pro Installation Guide
P8 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
7. Work-surface mounting
for
Worksurface
To attach the worksurface, place the worksurface with the top facing down
Lay the base assembly upside down on the top of the worksurface
Ensure that the base is properly positioned to the worksurface
Attach the base and hand-set to the worksurface using wood screws
The worksurface depth sould be center aligned with the cantilliever depth
and should have equal amount of overhang on each end
1
2
3
4
5
M5-20mm x 18
for
Handset
M5-16mm x 2
1
2
3
To attach the worksurface, start by laying the worksurface
down on the floor with the top down.
Lay the base assembly upside down on top of the
worksurface.
Double check to ensure that the base is properly positioned
on the underside of the worksurface, and then attach with
wood screws.
NOTE: The worksurface should be center aligned with the
cantiliver depth and should have equal amount of overhang
on each end.
Worksurface MountingPhase 6
for
Worksurface
M5-20mm x 2
for
Handset
M5-16mm x 18

ACTIV-Pro Installation Guide
P9 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Connecting Handset and PowerPhase 7
8. Connecting control and power
Left
motor
Right
motor
Handset
Power
Make sure that the Left motor plug into M1 port and the Right motor plug into M2 port
Connect power plug after the motors and the handset are connected properly
Connect each plugs according to the drawing.
Orientate yourself the the table assembly by facing as
a user to identify left and right motor.
1
2
Facing
Direction
Make sure that the Left motor plugs into the M1 port,
and the Right motor plugs into the M2 port.
Connect power plug after the motors
and handset are connected properly.
Reset the base by holding the
down arrow button until it reaches
its lowest height.
1
2
3
Connect each plug according to the drawing.
Orient yourself to the table assembly by facing
as a user to identify the left and right motors.

ACTIV-Pro Installation Guide
P10 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Phase 8 Program Height Memory Presets
1
2
To Program Up to 4 Presets: Use the up/down
arrows to find desired height, then press “M”
followed by the number 1, 2, 3 or 4.
To Test Programmed Height: Use the up/down
arrows to adjust the table to a height other
than the preset height. Then push
the number you programmed to see
if it automatically adjusts to the height
programmed in Step 1. You may need to
hold for 2-3 seconds to activate the base.
Note: If it does not adjust to the
programmed height, repeat Step 1
followed by Step 2.
A
M
Q
1
2
3
M
4

764 Walsh Avenue / Santa Clara, CA 95050 [phone] amqsolutions.com
5 Day Open Plan we provide exceptional
experiences with reliable, easy interactions
and successfully fulfilled orders in only 5 days