Anest Iwata WIDER1-13E2P User manual

1
INSTRUCTION MANUAL
Spray Gun
Be sure to observe warning sand cautions in this instruction manual.
Ifnot, itcan causepaintejectionand seriousbodilyinjuryby drawingorganicsolvent.
Be sure to observe following marked items which are especially important
. 
Indicates a potentially hazardous situation which, if not avoided, may result in serious injury or loss of
life.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury
or property damage.
Indicates notes which we ask you to observe. The safety precautions in this instruction manual are
the minimum necessary conditions. Follow national and local regulations regarding fire prevention,
electricity and safety as well as your own company regulations.
Symbol Marking on the Spray Gun:
II 2 G Ex h X
ThisANEST IWATAspray gun
complies with 2014/34/EU Directive
relatingto equipment andprotective
systems intended for use in explosive
potentially atmospheres.
II 2 G Ex h IIB T6 Gb X T
Amb
+5°C+40°C
Complies
with
European
Directive
Specific
Marking for
Explosion
Protective
Group II
(Surface)
Category
(Zone 1&2)
Typeof
Atmosphere
(GAS)
Ignition
Protection
(notapplied)
Explosion
Group
(Ethylene)
Temperature
Class
( 85°C)
Explosion
Protection
level
(EPL)
Additional
conditions:
Ambient
Temperature
AnystaticElectricity shouldbe
discharged andneedstobe
diverted to the groundviaa
conductive air hosenot
included.
Important specifications
Max. Pressure 0.70MPa / 7.0bar /100psi
Noiselevel 79dB(A)
Spraycondition Recommended
Measuring point 1m backwards fromspraygun,1.6m height
Max.temperature Atmosphere:5°C~40°C (41°F~104°F) AirandFluid:5°C ~43°C (41°F~109°F)
Important
Never connectpressure feeding paintexcept pressure feed type spraygun.
*1.Atomizing air pressure means air pressure at spray gun inlet when trigger is pulled and air flows.
Nozzle needleassy combination
Fluidnozzle Fluidneedle
Orifice mm (in) Mark Mark
0.8 (0.031) /W1 /08 08H WIDER1
1.0 (0.039) /W1 /10
1.3 (0.051) /W1 /13 13 WIDER1
1.5 (0.059) /W1 /15
1.8 (0.071) /W1 /18 18WIDER1
Main specifications
Model Type of feed Nozzle orifice
 mm (in)
Aircap assy
Mark
Recommended condition
Air consumption
l/min(cfm)
Pattern width
mm (in)
Air & fluid
connection
Mass
g (lbs.)
*1Atomizing air
pressure
MPa (bar / PSI)
Fluidoutput
ml/min
WIDER1
-
08E2P
Pressure
0.8
(0.031)
E2P
0.29
(3.0 / 43)
150
270 (9.5)
190 (7.5)
Air
G1/4
(NPS1/4)
Fluid
G1/4
(NPS1/4)
290
(0.64)
-
10E2P
1.0
(0.039)
200
220 (8.7)
-
13E2P
1.3 (0.051)
0.24
(2.5 / 36)
220 (7.8)
210 (8.3)
-
15E2P
1.5 (0.059)
250
240 (9.4)
WIDER1
-
10E1S
Suction
1.0 (0.039)
E1
85
75 (2.6)
120 (4.7)
-
13K1S
1.3 (0.051)
K1
150
145 (5.1)
155 (6.1)
-
13H2S
H2
225 (7.9)
160 (6.3)
-
13H4S
H4
0.2 (2.0 / 28)
140
210 (7.4)
180 (7.1)
-
15K1S
1.5 (0.059)
K1
0.24
(2.5 / 36)
175
145 (5.1)
170 (6.7)
-
15H2S
H2
170
225 (7.9)
175 (6.9)
-
18N1S
1.8 (0.071)
N1
210
170 (6.0)
170 (6.7)
WIDER1
-
10E1G
Gravity
1.0 (0.039)
E1
95
75 (2.6)
130 (5.1)
-
13K1G
1.3 (0.051)
K1
160
145 (5.1)
170 (6.7)
-
13H2G
H2
225
(7.9)
175 (6.9)
-
13H4G
H4
0.2 (2.0 / 28)
155
210 (7.4)
205 (8.1)
-
15K1G
1.5 (0.059)
K1
0.24
(2.5 / 36)
200
145 (5.1)
180 (7.1)
-
15H2G
H2
190
225 (7.9)
190 (7.5)
-
18N1G
1.8 (0.071)
N1
240
170 (6.0)
This manual contains IMPORTANT
WARNINGS and INSTRUCTIONS.
Equipment in this manual is exclusively for
painting purposes.
Do notuse for other purposes.
The operator shall be fully conversant with
the requirements stated in this instruction
manual including important warnings,
cautions and operation and correct handling.
Read and understand the instruction
manual, before use and retain for reference.
IMPORTANT WARNING: Our spray guns, airbrushes, and other products are made to conform by our local group companies with local
lawsand regulations
that may differ from place to place. Improper trade of products outside of designated domestic territories (unauthorized reselling) can resultin legal violations,
local fines, and penalties.ANEST IWATACORPORATION assumes no liability for products acquired throughunauthorized reselling and in suchcases and due
to quality control protocols, unauthorized reselling renders the warranty null and void.

2
■
Partslist
◆
Marked partsarewearableparts.
◎
When orderingparts, specify spraygun’smodel,partname with ref.No.andmarkedNo.ofair cap assy,fluidnozzleand fluidneedle.
◎
When replacing fluid nozzle or/and fluid needle,please replaceboth fluid nozzle and fluid needle assytogether.
◎
When receiving the spray gun, makesure thatit has not beendamaged during transport or storage and also check that all the
above contentsare inside the box.
■
Safety precautions
Fire and explosion
1.
Spark and open flames are strictly prohibited.
Paintscan be highly flammable and can cause fire.
Avoid any ignition sources such as smoking, open flames, electrical goods, etc.
2. Never use the following HALOGENATED HYDROCARBON SOLVENTS
which can cause cracks or dissolution on spray gun body (aluminum) by chemical reaction.
unsuitablesolvents
：
methyl chloride, dichloromethane, 1.2-dichloroethane,carbon tetrachloride, trichloroethylene, 1.1.1-trichloroethane
(Be sure that allfluids andsolvents are compatible with spray gun parts. We are ready to supplya material list used in the product)
3. Securely ground spray gun byusing air hose with built-in ground wire.
Ground wire should haveless than 1M resistant. Periodically check the ground for continuity.
Insufficient grounding can cause fire or explosion due to static electric sparking.
Improper use of equipment
1.
Never point
spraygun
toward people or animal.
If done, it can cause inflammation of eyes and skin or bodily injury.
2. Never exceed maximum operatingpressure or temperature.
3. Be sure to release air and fluid pressuresbefore cleaning, disassembling or servicing.
If not, remaining pressure can cause bodily injury or property damage.
To release pressure, first shut off the supply of compressed air and fluid to the spray gun.
Then squeeze trigger, while thespray is pointed in a safe direction.
4. Tip of fluid needle and tip offluid nozzlehas a sharp point.
Avoid touching the tip of the fluid needle or fluidnozzle during maintenance to prevent injury.
Protection of human body
1
．
Use only in a well
-
ventilated area (such as in a spray booth).
If not, poor ventilation can cause organic solvent poisoning and fire hazard.
2
．
Always wear protective gear
（
safetyglasses,mask, gloves
）
.
If not, paint, solvents, etc., can cause irritation of eyes and skin.
If you feel something wrong with eyes or skin, immediately see a doctor.
3
．
Wear earplugsif necessary.
Noise level can exceed 80dB(A), depending on operatingconditions and painting site
4
．
If operators pull the trigger many times during use, it may cause carpal tunnel syndrome.
Be sure to take a rest if you feel tired.
Other precautions
1.
Never alter this spray gun.
If done, it can cause insufficient performance and failure.
2. Only enter the working areasofother equipment (robots, reciprocators,etc.) after machines have safely been shutdown.
If not, contact with them can causeinjury.
3. Never spray foods or chemicals through this spraygun.
If done, it can cause accident by corrosion of fluid passages or adversely affect health by mixed foreign matter.
4. If something goes wrong, immediately stop operation and find the cause. Do not use again until you have solved theproblem.
No.
Description
Q’ty
No.
Description
Q’ty
1
A
ir capassy
1
9
Fluidneedlespringassy
1
◆
2
N
ozzle
needleass
y
1
10
F
luidAdj.knob
1
・
F
luidnozzle
◆
11
A
ir valveshaft
1
・
F
luid
needle
12
A
irAdj.assy
1
◆
3
N
eedlepackingset
1
13
T
rigger assy
1
4
P
atternAdj.assy
1
14
T
rigger studassy
1
5
A
ir valveseatassy
1
15
B
rush
1
a
ccessories
◆
6
A
ir valve
1
7
A
ir valvespring
1
8
F
luidAdj.guideassy
1

3
■
How to connect
・
Use clean airfiltered through air dryer and air filter. If not, dirty air can cause painting failure.
・
Beforeusing the spray gun for the first time, clean fluid passages with thinner to removerustpreventive oil.
If notcleaned, the rust preventive oil can cause paint failure, such as fish eyes.
・
Firmly connect hose or cup to spray gun. If not, disconnection of hose or drop of cup can cause bodily injury .
Step1. Connect an air hose to airnipple tightly.
Step2. Connect a fluid hose or a container to fluid nipple tightly.
Step3. Flush the spray gun fluid passage with a compatible solvent.
Step4. Pour paint into container, test spray and adjust fluid output as wellas pattern width.
■ Maintenance and inspection
・
First release air and pressure fully according to item No.3 of “Improper useof equipment” of WARNING on page 2.
・
Only an experienced person who is fully knowledgeable of the equipment should perform maintenance and inspection.
・
U
se neutralcleaner:
pH valueshallbe 6 to 8, otherwise could cause corrosion.
・
Only usegenuine ANEST IWATA parts for any maintenanceor repairs.
Step-by-step procedure
1.
Pour remaining paint to another container.
Clean fluid passages and
aircap assy
.
Spray a small amount of thinner into fluidpassages to clean them.
1.
Incompletecleaningcan resultin poorspraypatternandcontaminatedpaint.
It is especially important clean the gun fully and promptly after using two-component paint.
2.
Clean each section withbrush soaked with thinner and wipe out with waste cloth.
2.
Soaking whole spray gun in solvent may cause spray gun malfunction.
Also soaking air
cap assy. itself for extended period may cause a defective spray pattern.
When cleaning, never scratch the air cap assy., fluid nozzle, or fluid needle.
Avoid touching or damaging the tipof the fluid nozzle or needle.
3. Before disassembly, fully clean fluid passages.
Remove fluid nozzle, using a ring spanner, box wrench or optional accessory spanner
(code 93538601)
3. Duringdisassembly, avoid scratching the needleseatingsurface.
Either first remove the fluid needle or hold the trigger back while removing the fluid nozzle,
to protect the seating surface.
4.
If you need to adjust fluid needle packing set, first tighten it by hand (with fluid needle in
place). Then tighten it further about1/6 turn (60-degree) by spanner.
When you remove needle packing set, do not leave the plastic tip of the packing in the
spray gun body.
4.
If you tighten the fluid needle packing set too much, fluid needle will not move smoothly,
resulting in paint leakage from tip of the fluid nozzle. Try to adjust it carefully while pulling
thetrigger and confirming smooth movement of the fluid needle.
If you tighten it too much, first fully loosen it andthen retighten again carefully.
5. To assemble the airvalve, first assemblethe airvalve, air valve spring, andfluidadj. guide
assy. together. Next, insert fluid needle into fluid adj. guide assy., then fit it to spray gun
body and screwfluid adj. guide assy. in.
5.
If you try to fit air valve spring and air valve to the spray gun body without the fluid
needle, the air valve may not be fitted correctly and the packing inside fluid adj. guide
assy. can be damaged.
6. Before assembling the pattern adj.assy. or air adj. assy.back on to the gunbody, fully turn
the adjustment knobs counterclockwise to open. Once in the gun body the pattern adj.
knob and air adj. knob can be tightened.
6. If pattern adj. knob or air adj. knob is not fully opened when tightening into gun body,the tip
of it can contact and damage the seating surface.
7. When you assemble the needle spring on the fluid needle, the plastic tip should be on the
opposite sideas the fluid needle tip.
7. If plastic tip is on the wrong side, it may not operate normally. Incorrect installation of the
needle spring may cause a heavy triggerpull.
Where to inspect
Parts replacement standard
1. Eachhole passage of air cap assy and fluid nozzle Replaceif it is crushed or deformed.
2. Packing and O ring Replaceif it is deformed or worn out.
3. Leakage from seatingsurface between fluid nozzle and fluid needle Replacethem if leakage does not stop after fully cleaning the fluid nozzle and needle.
If you replace the fluid nozzle or fluid needle only, ensure they fully match and confirm that
thereisno leakage.
Fluidneedle
Needlespringassy
Plastictip
Fluid (Gravity)
Fluidnipple
Fluid
(Suction /Pressure)
Air
Airnipple

4
■
Troubleshooting
Spray Pattern
Problems
Remedies
Fluttering
1. Air enters between fluid nozzle and taperedseat of spray gun body.
2. Air is drawnfrom fluid needle packing set.
3. Air enters at fluid container fitting nut or fluid hose joint.
1. Remove fluid nozzle to clean seat. If it is damaged, replace nozzle.
2. Tighten fluid needlepacking.
3. Fully tightenjoint section.
Crescent
1. Paint buildup on air cap assy. partially clogs horn holes.
Air pressure from both horns differs.
1. Remove obstructionsfrom horn holes with attached brush.
But do not use metal objects to clean horn holes.
Inclined
1. Paint buildup or damage on fluid nozzle circumference and air cap
assy. center.
2. Fluid nozzle is not properly fitted.
1. Removeobstructions.
Replaceif damaged.
2. Remove fluid nozzle and clean seat section.
Split
1. Paint viscosity too low.
2. Fluid output too high.
3. Pattern airpressure is too high.
1. Add paint to increase viscosity.
2. Turn fluidadj. knob clockwise to reduce fluid output.
3. Turn pattern adj. assy. clockwiseto reduce pattern air pressure.
Heavy Center
1. Paint viscosity is too high.
2. Fluid output is too low.
1. Add thinner to reduceviscosity.
2. Turnfluid adj.knob counter-clockwiseto increasefluidoutput.
Spit
1. Fluid nozzle andfluid needle are not seated properly.
2. The first-stagetravel of trigger (when only air discharges) decreases.
3. Paint buildup inside air cap assy.
1. Clean or replace fluid nozzle and fluid needle assy..
2. Replacefluid nozzleand fluidneedle assy.
3. Clean air cap assy.
R1: retighten R2: adjust R3: clean R4: replace parts
Problem
W
here it
occurred Parts to be checked Cause
R
emedy
R
1
R
2
R
3
R
4
Paintleaks
Fluid nozzle
Fluid nozzle ~ Fluid needle
Dirt, damage, wear on seat
〇 〇
Loose fluid needle adj. knob
〇
Wear on needle spring
〇
Fluid nozzle ~ Spray gun body Insufficient tightening
〇
Dirt or damage on seat
〇 〇
Needle packing set Fluid needledoes not return due to packing set too tight
〇 〇
Fluid needle does not return due to paint buildup on fluidneedle
〇 〇
Needle packing
set
Needle packing set
~ Fluid needle Wear
〇 〇
Needle packing set Insufficienttightening
〇
Paint does not
come out Tip ofspraygun
Fluid adj. knob Insufficient opening
〇
Tip holeof fluid nozzle Clogged
〇
Needle packing set
~ Fluid needle
Clogged
〇 〇
Insufficienttightening
〇
Airleaks
(from tip of air cap
assy)
Air valve &
Air valve seat assy
Air valve Dirt or damage on seat
〇 〇
Air valve seat assy Dirt or damage on seat
〇 〇
Wear on air valve spring
〇
■ How to operate
・
Suggested air pressure is 2.0 to 3.5 bar (29 to 50 PSI).
・
Recommended paint viscosity differs according to paint property and painting conditions.
14 to 25 sec. / Ford cup#4 is recommendable.
・
Keep fluid output assmall as possible to the extent that the job will not be hindered.
It will lead to better finishing with fine atomization.
・
Set the spraydistance from the spray gun to the work piece as near as possible within the range of 150~200 mm (5.9~7.9 in).
・ The spray gun should be held so that it is perpendicular to the surface of the work piece at all times.
Then, the spray gun should move in a straight and horizontal line. Arcing the spray gun causes uneven painting.
Manual No. T924-02
Code No. 03012690
150~200 mm
(5.9~7.9 in)
× ×
3176, Shinyoshida-cho, Kohoku-ku, Yokohama, 223-8501, Japan

１
Residual Risk Map Requiring Protective Measures by Machine Users
(Abbreviated Name: Residual Risk Map)
Product model: "Spray gun :WIDER1 / WIDER2"
2019/5/29 Create
ANEST IWATA Corporation
※
Be sure toread and understand the instruction manual before usingthe product. This document is areference material in the instruction manual and must
not be used with only an understanding of the contents of this document.
Residual risk is classified and described according to the following definitions
DANGER Contents that are likely to cause death or serious injury if protection measures are not implemented.
WARNING Contents that may cause death or serious injury if protection measures are not implemented.
CAUTION Contents that may cause minor injury if protection measures are not implemented
Symbols and numbers shown in the figure correspond to those described in the "List of Residual Risks" of the Product. Refer to the List of Residual Risks for
details of each residual risk.
Residual risk that is notidentified on the machine
DANGER

WARNING No.3 , No.5 , No.6 , No.7 , No.8 , No.9
CAUTION 
Location
A
DANGER 
WARNING No.1,No.10
CAUTION 
Location
B
DANGER 
WARNING No.2
CAUTION 
Location
C
DANGER 
WARNING No.4
CAUTION 
Location
D
DANGER 
WARNING 
CAUTION No.11
Residual risk

２
List of residual risks requiring protection measures by machine users
(Abbreviated Name: List of Residual Risks)
Product model: " Spray gun :WIDER1 / WIDER2"
2019/5/29 Create
ANEST IWATA Corporation
※
Be sure toread and understand the instruction manual before usingthe product. This document is areference material in the instruction manual and must
not be used with only an understanding of the contents of this document.
※
1 "degree of hazard" is classified and described according to the following definitions
DANGER Contents that are likely to cause death or serious injury if protection measures are not implemented.
WARNING Contents that may cause death or serious injury if protection measures are not implemented.
CAUTION Contents that may cause minor injury if protection measures are not implemented
※
2 The symbol shown as "Location on machinery" is the number of the machine section on the Residual Risk Map of the Product. See Residual Risk Map
for specific points on the machinery.
No.
Operatio
nal
Phase
Works
Qualifications
and Training
required for
the work
Location on
the
machinery
*2
Harm
Degree
*1
Type of Harm
Protective measure protective
measure performed by the
machinery user
Instruction
Manual
Referenced
page
1
Use
Preparation
work
During work

A
Warning
A wrong connection between the air joint
and the paint joint may cause paint to
spout from an unexpected place and hit
the operator.
To provide personal protective
equipment P2
2
Use All

B
Warning
Ignition and fire caused by static electricity Use of a hose with a ground and
confirmation of ground P2
3
Use and
mainten
ance
During work,
decompositi
on and rinse

Default
Warning
Organic solvents, etc., may come into
contact with the eyes and skin, causing
irritation.
To provide personal protective
equipment P2
4
Use During work

C
Warning
Tenosynovitis due to repeated pulling of
the trigger Moderate rest P2
5
Use All

Default
Warning
Fire, electrical appliances, etc. ignite, and
fire generatings. Strict ban on the use of fire P2
6
Use
Preparation
work
During work

Default
Warning
Supply at specified pressure or higher,
paint spouts from unexpected places,
hitting human body or eyes, blindness
To provide personal protective
equipment P2
7
Use and
mainten
ance
Preparation
work
During work

Default
Warning
The product is modified, parts other than
genuine parts are used, and an
unexpected failure or accident
generatings.
No modification
Use of genuine parts P2
8
Use
Preparation
work
During work

Default
Warning
The patient stayed in a location where
noise such as blowing air was generated
fora long time, resulting in hearing loss.
Use of earplugs is recommended. P2
9
Use and
mainten
ance
During work,
decompositi
on and rinse

Default
Warning
Organic solvent poisoning Due to inhale
of solvent and paint mist
To provide personal protective
equipment
Work in painting booths, etc.
P2
10
Use and
mainten
ance
Preparation
work
During work

A
Warning
If the hoses
are
triad to be disconnected
under pressurized condition, paint,
cleaning liquid, air, etc. are spouted out
and injured.
To provide personal protective
equipment
Remove residual pressure
P2
11
Mainten
ance
Preparation
work

D
Caution
Needle valve piercing with sharp corners To provide personal protective
equipment P2
Residual risk
No.R003-00
Code No.03014490