Anritsu Site Master S113C User manual

Site Master
S113C, S114C,
S331C, S332C,
Antenna, Cable and
Spectrum Analyzer
User's Guide
Hand-Held Tester for Transmission Lines
and other RF Components

WARRANTY
The Anritsu product(s) listed on the title page is (are) warranted against defects in
materials and workmanship for one year from the date of shipment.
Anritsu's obligation covers repairing or replacing products which prove to be defec-
tive during the warranty period. Buyers shall prepay transportation charges for
equipment returned to Anritsu for warranty repairs. Obligation is limited to the origi-
nal purchaser. Anritsu is not liable for consequential damages.
LIMITATION OF WARRANTY
The foregoing warranty does not apply to Anritsu connectors that have failed due to
normal wear. Also, the warranty does not apply to defects resulting from improper or
inadequate maintenance by the Buyer, unauthorized modification or misuse, or op-
eration outside the environmental specifications of the product. No other warranty is
expressed or implied, and the remedies provided herein are the Buyer's sole and
exclusive remedies.
TRADEMARK ACKNOWLEDGMENTS
MS-DOS, Windows, Windows 95, Windows NT, Windows 98, Windows 2000 and
Windows ME are registered trademarks of the Microsoft Corporation.
Anritsu and Site Master are trademarks of Anritsu Company.
NOTICE
Anritsu Company has prepared this manual for use by Anritsu Company personnel
and customers as a guide for the proper installation, operation and maintenance of
Anritsu Company equipment and computer programs. The drawings, specifications,
and information contained herein are the property of Anritsu Company, and any un-
authorized use or disclosure of these drawings, specifications, and information is
prohibited; they shall not be reproduced, copied, or used in whole or in part as the
basis for manufacture or sale of the equipment or software programs without the
prior written consent of Anritsu Company.
October 2001 10580-00060
Copyright ã2001 Anritsu Co. Revision: A

Table of Contents
Chapter 1 - General Information
Introduction..................................1-1
Description ..................................1-1
Standard Accessories.............................1-1
Options ....................................1-2
Optional Accessories .............................1-2
Performance Specifications .........................1-3
Preventive Maintenance ...........................1-6
Calibration ..................................1-6
InstaCal Module ...............................1-7
Annual Verification..............................1-7
Chapter 2 - Functions and Operations
Introduction..................................2-1
Test Connector Panel.............................2-1
Front Panel Overview ............................2-2
Function Hard Keys .............................2-3
Keypad Hard Keys ..............................2-4
Soft Keys ...................................2-6
Power Monitor Menu ............................2-15
Symbols ...................................2-19
Self Test ...................................2-19
Error Codes .................................2-19
Self Test Errors ..................................2-19
Range Errors ...................................2-21
InstaCal Error Messages .............................2-22
Battery Information.............................2-24
Charging a New Battery ..........................2-24
Charging the Battery in the Site Master.....................2-24
Charging the Battery in the Optional Charger .................2-24
Battery Charge Indicator .............................2-25
Battery Life ....................................2-25
Important Battery Information .........................2-26
Chapter 3 - Getting Started
Introduction..................................3-1
Power On Procedure .............................3-1
Select the Frequency or Distance ......................3-2
Calibration ..................................3-2
Calibration Verification ..............................3-3
Manual Calibration Procedure ..........................3-4
InstaCal Module Verification ...........................3-5
InstaCal Module Calibration Procedure .....................3-6
Calibration with the Test Port Extension Cable .................3-6
i

Setting the Scale................................3-7
Auto Scale ......................................3-7
Amplitude Scale...................................3-7
Save and Recall a Setup ...........................3-7
Saving a Setup ...................................3-7
Recalling a Setup ..................................3-8
Save and Recall a Display ..........................3-8
Saving a Display ..................................3-8
Recalling a Display .................................3-8
Set the Distance and Cable Type .........................3-9
Changing the Units .................................3-9
Changing the Display Language..........................3-9
Printing....................................3-10
Printing a Screen .................................3-10
Printer Switch Settings ..............................3-11
Using the Soft Carrying Case........................3-12
Chapter 4 - Cable & Antenna Measurements
Introduction..................................4-1
Line Sweep Fundamentals ..........................4-1
Information Required for a Line Sweep ..................4-2
Typical Line Sweep Test Procedures ....................4-3
System Return Loss Measurement ........................4-3
Insertion Loss Measurement............................4-4
Distance-To-Fault (DTF) Transmission Line Test ................4-8
Antenna Subsystem Return Loss Test ......................4-10
Chapter 5 - Spectrum Analyzer Measurements
Introduction..................................5-1
Occupied Bandwidth .............................5-1
Channel Power Measurement ........................5-2
Channel Power Measurement with the Site Master ...............5-2
Adjacent Channel Power Measurement ..................5-4
Out-of-Band Spurious Emission Measurements ..............5-6
In-Band/Out-of-Channel Measurements ..................5-7
Field Strength Measurement.........................5-8
Antenna Calculations.............................5-9
Chapter 6 - Power Measurement
Introduction..................................6-1
Power Measurement .............................6-1
ii

Chapter 7 - Site Master Software Tools
Introduction..................................7-1
Features ....................................7-1
System Requirements.............................7-1
Installation ..................................7-2
Communication Port Setting............................7-2
Interface Cable Installation ............................7-3
Using Software Tools .............................7-3
Downloading Traces from the Site Master .................7-3
Plot Capture..................................7-4
Plot Properties ................................7-4
Trace Overlay or Plot Overlay...........................7-5
Saving Traces ....................................7-5
Custom Cable List .................................7-6
Entering Antenna Factors .............................7-7
Uploading Antenna Factors ............................7-8
Creating a Database ................................7-8
Printing Formats ..................................7-8
Appendix A - Reference Data
Coaxial Cable Technical Data........................A-1
Appendix B - Windowing
Introduction .................................B-1
Examples ...................................B-1
iii/iv

Chapter 1
General Information
Introduction
This chapter provides a description, performance specifications, optional accessories, pre-
ventive maintenance, and calibration requirements for the Site Master models S113C,
S114C, S331C, and S332C. Throughout this manual, the term Site Master will refer to the
models S113C, S114C, S331C, and S332C.
Model Frequency Range
S113C
S114C
S331C
S332C
2 to 1600 MHz
2 to 1600 MHz, 100 kHz to 1600 MHz Spectrum Analysis
25 to 4000 MHz
25 to 4000 MHz, 100 kHz to 3000 MHz Spectrum Analysis
Description
The Site Master is a hand held SWR/RL (standing wave ratio/return loss), and Distance-To-
Fault (DTF) measurement instrument that includes a built-in synthesized signal source. All
models include a keypad to enter data and a liquid crystal display (LCD) to provide graphic
indications of SWR or RL over the selected frequency range and selected distance. The Site
Master is capable of up to 2.5 hours of continuous operation from a fully charged
field-replaceable battery and can be operated from a 12.5 dc source. Built-in energy conser-
vation features can be used to extend battery life over an eight-hour work day.
The Site Master is designed for measuring SWR, return loss, or cable insertion loss and lo-
cating faulty RF components in antenna systems. Power monitoring is available as an op-
tion. Site Master models S114C and S332C include spectrum analysis capability. The
displayed trace can be scaled or enhanced with frequency markers or limit lines. A menu
option provides for an audible “beep” when the limit value is exceeded. To permit use in
low-light environments, the LCD can be back lit using a front panel key.
Standard Accessories
The Software Tools PC-based software program provides a database record for storing
measurement data. Site Master Software Tools can also convert the Site Master display to a
Microsoft Windowsä95/98/NT4/2000/ME workstation graphic. Measurements stored in
the Site Master internal memory can be downloaded to the PC using the included null-mo-
dem serial cable. Once stored, the graphic trace can be displayed, scaled, or enhanced with
markers and limit lines. Historical graphs can be overlaid with current data, and underlying
data can be extracted and used in spreadsheets or for other analytical tasks.
The Site Master Software Tools program can display all of the measurements made with the
Site Master (SWR, return loss, cable loss, distance-to-fault) as well as providing other func-
tions, such as converting display modes and Smith charts. Refer to Chapter 7, Software
Tools, for more information.
1-1
1

The following items are supplied with the basic hardware.
·Soft Carrying Case
·AC-DC Adapter
·Automotive Cigarette Lighter 12 Volt DC Adapter,
·CDROM disk containing the Software Tools program. This program contains Fault Lo-
cation (DTF) and Smith Chart functions
·Serial Interface Cable (null modem type)
·InstaCal Module
·One year Warranty (includes battery, firmware, and software)
·User's Guide
Options
·Option 5 — Add Power Monitor
Optional Accessories
·Anritsu Precision N (m) Open/Short/Load, 42 dB, Part No. OSLN50LF
·Anritsu Precision N (f) Open/Short/Load, 42 dB, Part No. OSLNF50LF
·Anritsu Precision N (m) Short/Open, Part No. 22N50
·Anritsu Precision N (f) Short/Open, Part No. 22NF50
·Site Master Precision N (m) Load, 42 dB, Part No. SM/PL
·Site Master Precision N (f) Load, 42 dB, Part No. SM/PLNF
·7/16 (m) Precision Open/Short/Load, Part No. 2000-767
·7/16 (f) Precision Open/Short/Load, Part No. 2000-768
·Adapter, Precision N (m) to N (m), Part No. 34NN50A
·Adapter, Precision N (f) to N (f), Part No. 34NFNF50
·Adapter, 7/16 (f) to N (m), Part No. 510-90
·Adapter, 7/16 (f) to N (f), Part No. 510-91
·Adapter, 7/16 (m) to N (m), Part No. 510-92
·Adapter, 7/16 (m) to N (f), Part No. 510-93
·Adapter, 7/16 DIN (m) to 7/16 DIN (m), Part No. 510-96
·Adapter, 7/16 DIN (f) to 7/16 DIN (f), Part No. 510-97
·Armored Test Port Extension Cable, 1.5 meter, N (m) to
N (f), Part No. 15NNF50-1.5C
·Armored Test Port Extension Cable, 3.0 meter, N (m) to
N (f), Part No. 15NNF50-3.0C
·Armored Test Port Extension Cable, 5.0 meter, N (m) to
N (f), Part No. 15NNF50-5.0C
·Armored Test Port Extension Cable, 1.5 meter, N (m) to
N (m), Part No. 15NN50-1.5C
1-2
Chapter 1 General Information

·Armored Test Port Extension Cable, 3.0 meter, N (m) to
N (m), Part No. 15NN50-3.0C
·Armored Test Port Extension Cable, 5.0 meter, N (m) to
N (m), Part No. 15NN50-5.0C
·Armored Test Port Extension Cable, 1.5 meter, N (m) to
7/16 DIN (f), Part No. 15NDF50-1.5C
·Armored Test Port Extension Cable, 1.5 meter, N (m) to
7/16 DIN (m), Part No. 15ND50-1.5C
·RF Detector, 1 to 3000 MHz, N(m) input connector, 50 Ohms, Part No. 5400-71N50
·RF Detector, 0.01 to 20 GHz, N(m) input connector, 50 Ohms, Part No. 560-7N50B
·Transit Case for Site Master, Part No. 760-215A
·Antenna SMA (f), 50 W, 1.71 to 1.88 GHz, Part No. 2000-1030
·Antenna SMA (f), 50 W, 1.85 to 1.99 GHz, Part No. 2000-1031
·Antenna SMA (f), 50 W, 2.4 to 2.5 GHz, Part No. 2000-1032
·Antenna SMA (f), 50 W, 806 to 869 MHz, Part No. 2000-1034
·Antenna SMA (f), 50 W, 896 to 941 MHz, Part No. 2000-1035
·HP Deskjet 350 Printer, Part No. 2000-766
·Serial-to-Parallel Converter Cable (use with the HP 350 Printer), Part No. 2000-753
·Seiko DPU-414 Thermal Printer, Part No. 2000-754 (U.S.) or
2000-761 (Europe)
·US Adapter (use with the DPU-414 Printer),
Part No. 2000-1002
·Europe Adapter (use with the DPU-414 Printer)
Part No. 2000-1003
·Japan Adapter (use with the DPU-414 Printer)
Part No. 2000-1194
·Battery Pack (use with the DPU-414 Printer)
Part No. 2000-1004
·Serial Interface Cable (use with the DPU-414 Printer),
Part No. 2000-1012
·Thermal Paper (use with the DPU-411/DPU-414 Printer),
Part No. 2000-755
·Rechargeable Battery, NiMH
Part No. 633-27
·Battery Charger with universal power supply, NiMH only
Part No. 2000-1029
Performance Specifications
Performance specifications are provided in Table 1-1, on the following page.
1-3
Chapter 1 General Information