Antunes DCH-220 SQ User manual

®
DCH-220 SQ
Owner’s Manual
Display Cabinet Heated
Manufacturing Numbers:
9500731 & 9500732
www.antunes.com P/N 1012041 Rev E 08/23

2
®
P/N 1012041 Rev E 08/23
Overview
The Antunes Display Case attractively
displays your food and maintains it at
ready-to-eat temperature. A convec-
tion fan (some models) circulates heat
throughout the entire display cabinet
while a digital temperature control main-
tains a constant temperature. Humidity
water trays (some models) extend food
holding times by reducing moisture loss.
Models DCH-100, DCH-200, and DCH-
300 are primarily for meats and poultry
products.
Models DCH-120, DCH-220, and DCH-
320 are primarily designed for bread
products.
Before Use
This manual contains safety, installation,
and operating procedures for the display
cabinet. Read and understand it com-
pletely before installing or operating the
display cabinet. Keep this document for
reference. If the heated display cabinet
changes ownership, this manual must
accompany it.
In Case of Damage
If the display cabinet arrives damaged,
le a claim with the carrier immediately.
Save all packing materials when ling
a claim. Freight damage claims are the
responsibility of the purchaser and are
not covered under warranty.
Website
www.antunes.com
Service/Technical
Assistance
In Case of Damage
If any parts are missing or damaged, con-
tact Antunes Customer Service immedi-
ately at [phone] (toll free).
If there are problems with the installa-
tion or operation of this product, contact
Antunes Technical Service toll free at
[phone].
Fill in the information in the next col-
umn and have it handy when calling for
assistance. The serial number is on the
specication plate located on the system.
Equipment Information to Save
Purchased from:
Date of purchase:
Model number:
Serial number:
Manufacturing number:
Authorized Service Agency
Name:
Phone No:
Address:
Contents
Overview................................................2
Before Use ...........................................2
In Case of Damage ..............................2
Website ................................................2
Service/Technical Assistance..............2
In Case of Damage ..............................2
Equipment Information to Save............2
Safety Information................................3
Installation............................................3
Operation .............................................3
Maintenance.........................................3
Service .................................................3
Heated Display Cabinet
Glass Warnings ................................ 4
Specications .......................................5
Dimensions ..........................................5
Electrical Ratings .................................5
Installation.............................................6
Unpacking ............................................6
Equipment Setup..................................6
Operating & Programming...................7
Maintenance.........................................8
Daily Cleaning......................................8
Parts Replacement ...............................8
Halogen Bulb Replacement .................8
Rear door replacement ........................8
Front glass panel replacement.............9
Side glass replacement........................9
Top Glass Replacement.......................9
Display Codes .................................... 10
Operations and Programming ........... 11
Troubleshooting .................................12
Replacement Parts Sheet 1 ...............13
Replacement Parts Sheet 2 ...............14
Wiring Diagram ...................................15
Wiring Diagram ..................................16
Notes....................................................17
Limited Warranty ........................... 19

®
3
P/N 1012041 Rev E 08/23
Safety Information
Installation
yRead and understand all
instructions before installing or
using the eated display cabinetr
yInstall and locate the equipment
only for its intended use as
described in this manual.
yAll electrical connections must
be in accordance with local
electrical codes and any other
applicable codes. The equipment
must be grounded according to
local electrical codes to prevent
electrical shocks. It requires a
grounded receptacle with separate
electrical lines, protected by fuses
or a properly-rated circuit breaker.
yElectrical ground is required
on this appliance. Consult a
qualied electrician if there is any
uncertainty about whether the
appliance is properly grounded.
yDo not modify the power supply
cord plug. If it does not t the
outlet, have a proper outlet
installed by a qualied electrician.
yDo not use an extension
cord with this appliance.
Operation
yThe heated display cabinet is
furnished with a properly grounded
cord connector. Do not attempt to
defeat the grounded connector.
yDo not operate the heated
display cabinet if it has been
damaged or dropped, if it has
a damaged cord or plug, or if
it is not working properly.
yDo not block or cover any
openings on the equipment.
yDo not immerse the cord
or plug in water.
yKeep the cord away from
heated surfaces.
yDo not allow the cord to hang over
the edge of a table or counter.
Maintenance
yDo not use abrasive materials; they
can damage the heated display
cabinet’s stainless steel nish.
yDo not use corrosive chemicals
in this equipment.
yChlorides or phosphates in
cleaning agents (e.g., bleach,
sanitizers, degreasers, and
detergents) can permanently
damage stainless steel equipment.
The damage is usually in the form
of discoloration, dulling of the metal
surface nish, pits, voids, holes, or
cracks. This damage is permanent
and is not covered by warranty.
yUse only chemical cleaners
that are safe for cast aluminum.
Observe all precautions and
warnings on product labels.
yAlways use a soft, damp cloth
for cleaning. Rinse with clear
water and wipe dry. When
required, always rub in the
direction of metal polish lines.
yRoutine cleaning should be
performed daily with soap,
ammonia detergent, and water.
ySponge stains and hard water
spots with a 50% vinegar solution.
yRub o󰀨 nger marks and
smears using soap and water.
yDo not clean the heated display
cabinet with a water jet.
Service
yInspection, testing, and
repair of electrical equipment
must be performed only by
qualied service personnel.
yHave the heated display
cabinet serviced only by
qualied personnel. Contact
Antunes Technical Service
for adjustment or repair.
yTurn the power o󰀨, unplug the
power cord, and allow unit
to cool to room temperature
before performing any
service or maintenance.
yIf the supply cord is damaged,
it must be replaced by the
manufacturer, its service agent,
or a similarly qualied person in
order to avoid an electrical hazard.

4
®
P/N 1012041 Rev E 08/23
DO NOT scratch, chip, or nick the glass.
DO NOT place any metal objects in contact with the glass (merchandise holders, signs,
etc.).
DO NOT transfer coins over the unit.
DO NOT use the glass as a serving counter.
When cleaning, handling, or removing the glass, make sure that the
glass is cool (room temperature).
USE approved cleaners marketed for glass cleaning only.
USE a at surface covered with a soft cloth to place the glass on, if the glass is removed.
USE a clean, soft cloth when cleaning the glass. Do not use paper towels.
USE light pressure when wiping/cleaning the glass.
MAKE SURE that the top cover glass does not touch the edge of the side glass.
MAKE SURE to replace scratched, chipped, nicked, cracked, or broken glass.
Please follow the Safety Instructions below in order to reduce the chance of
damaged/broken glass:
Warning: Mishandling this product or failure to follow these instruc-
tions may result in shattering glass.
Heated Display Cabinet Glass Warnings
(DCH Models)

®
5
P/N 1012041 Rev E 08/23
Dimensions
Electrical Ratings
Model &
Mfg. No. Description Configuration
DCH-220
9500731
Power Cord
NEMA 5-20P
20 Amp., 120 Volt
DCH-220
9500732
Power Cord
16 Amp, 250V
Model &
Mfg. No. Volts Watts Amp. Hz.
DCH-220
9500731 120 1800 15.0 50/60
DCH-220
9500732 230 1800 16 50/60
Specications
CAUTION
All electrical connections must be in
accordance with local electrical codes
and any other applicable codes.
WARNING
ELECTRICAL SHOCK HAZARD.
Failure to follow the instructions in this
manual could result in serious injury or
death.
yElectrical ground is required
on this appliance.
yDo not modify the power
supply cord plug. If it does
not t the outlet, have a
proper outlet installed by
a qualied electrician.
yDo not use an extension
cord with this appliance.
yCheck with a qualied
electrician if you are in doubt
as to whether the appliance
is properly grounded.

6
®
P/N 1012041 Rev E 08/23
Installation
Unpacking
1. Remove unit and all packing materi-
als from shipping carton.
2. Open the large box. Remove all
packing materials and protective
coverings from the unit and parts.
NOTICE: If any parts are missing, con-
tact Antunes IMMEDIATELY at
1-877-392-7854 in the U.S., or
630-784-1000 outside the U.S..
3. Wipe all surfaces of the unit with a
hot damp cloth.
NOTICE: Do not use a dripping wet
cloth. Wring out before use.
Equipment Setup
CAUTION
All electrical connections must be
in accordance with local electrical
codes and any other applicable
codes.
When placing the unit into service,
pay attention to the following guide-
lines:
yMake sure power to the
unit is off and the unit is
at room temperature.
yDo not block or cover any
openings on the unit.
yDo not immerse cord
or plug in water.
yKeep cord away from
heated surfaces.
yDo not allow cord to hang
over edge of table or counter.
yPlace unit on a sturdy, level
table or work surface.
yEnsure that the line voltage
corresponds to the stated
voltage on the unit specication
label located at the end
of the power cord.
yTurn the Rocker Switch (power
On/O󰀨) to OFF. Connect the
unit to the power supply.
Figure 1. DCH-220
Heating Element Shield
Heating
Element
Shelf
Pan Supports
Crumb
Tray
Note: DCH-220 has only 1 heater
& heat shield
Note: DCH-220 has only 1
support
Figure 2. Display Components (DCH-320 Shown)

®
7
P/N 1012041 Rev E 08/23
TEMP
UP
TEMP
DOWN
TEMP
SCALE
F
C
O
O
Figure 3. Controls
Figure 4. Loading Pans
Operating &
Programming
NOTICE: The Setpoint temperature is
the desired cabinet temperature
setting. When the Temp UP
button is pressed and held (and
provided that the unit is up to
temperature), the actual cabinet
temperature is displayed. When
the button is released, the Set-
point temperature is displayed.
1. Turn the unit ON. The display will
ash “LO” to indicate that the unit
is heating up. After 20-30 minutes
(when the unit is up to temperature),
the display will show the setpoint
temperature.
2. To adjust the setpoint temperature,
press and hold the Temp Up and
Temp Down buttons until the display
begins to ash. Release the buttons.
Then, press the Temp Up or Temp
Down buttons to raise or lower the
setpoint temperature. Release
when the display shows the desired
temperature.
3. To change the display from Fahren-
heit to Celsius and back, press and
hold the Temp Scale button (Figure
3) for 2-3 seconds and release.
4. Open the rear door(s) and place the
serving table pan(s) into the unit
(Figure 4). Load the pan(s) with the
food product using tongs or a similar
utensil. Close the door(s).
Rocker Switch
(Power On/O󰀨)
Control Panel Key Pad
NOTE: Back of unit shown
NOTE: DCH-220 holds only 2 pans

8
®
P/N 1012041 Rev E 08/23
Maintenance
Be sure to follow all of the warnings and
precautions listed in the Important Safe-
ty Information section of this manual.
WARNING
Turn the unit o󰀨, disconnect the pow-
er source and allow the unit to cool
down before performing any service
or maintenance on the unit.
CAUTION
Do not remove crumb tray while unit
is hot or burns or other personal
injury may result.
WARNING
All glass surfaces must be cool be-
fore cleaning. Once cool, wipe glass
with a clean cloth. Do not attempt
to clean glass when hot or with cold
towel as shattering glass may occur.
Daily Cleaning
The unit requires a minimum amount
of maintenance. To ensure proper
operation, clean the unit at the end of
each serving day.
1. Turn unit o󰀨, unplug the power cord,
and allow the unit to cool to room
temperature.
2. Once cooled, remove all compo-
nents. Wipe the glass panels with a
clean cloth sprayed with an ap-
proved glass cleaner.
3. Wash all components in soap and
water. Wipe all surfaces of the unit
with a damp cloth.
NOCE: Do not use a dripping wet cloth.
Wring the cloth out before use.
4. Install components in unit.
Parts Replacement
Halogen Bulb Replacement
CAUTION
Do not handle halogen bulbs with
bare hands. Use a tissue or clean
cloth to handle halogen bulbs
CAUTION
Use 1000 Watt (Max.) Quartz tung-
sten halogen lamp (T4 Bulb/‘RSC’
Base) only. To reduce the risk of elec-
tric shock when replacing bulbs, turn
display switch to OFF position.
1. Turn the unit o󰀨.
2. Unplug the power cord from the
electrical outlet and allow the unit
to cool to room temperature before
proceeding.
3. Gently, but rmly, press the lamp
socket sideways and remove the
bulb (Figure 5).
4. Install a new 100 watt bulb while
pressing the socket sideways. Make
sure bulb is fully seated before
releasing socket.
Figure 5. Halogen Bulb Replacement
Rear door replacement
5. Turn unit o󰀨, unplug the power cord,
and allow the unit to cool to room
temperature.
6. Firmly grasp the sides of one glass
door. Lift the door up and out of the
bottom track (Figure 6). Repeat for
the other door.
7. Place new door in the inside upper
track. Push up rmly and slide bot-
tom of door into bottom inside track.
Install other door into outside tracks
the same way.
Figure 6. Halogen Bulb Replacement

®
9
P/N 1012041 Rev E 08/23
Front glass panel replacement
1. Turn the unit OFF, unplug the power
cord from the electrical outlet, and
allow the unit to cool to room tem-
perature before proceeding.
2. Turn the two security paddles to
align with the slot of brackets at
each corner (Figure 7).
3. Tilt the front glass away from the
unit on the hinge plate and remove
the panel from the unit.
4. (See Caution note).
5. To reinstall, be sure the front glass
is fully seated in the hinge plate.
Then, tilt the glass into place and
install the nylon spacers, washers,
and thumb screws.
CAUTION
Front glass panel replacement
should be performed by two people
to prevent damage to the glass.
Unlocked Position
Figure 7. Security Paddles
(Unlocked Position)
(Front Corners Only)
Figure 8. Front Glass Replacement
Front
Glass
Figure 9. Side Glass Replacement
Side glass replacement
1. Turn the unit OFF, unplug the power
cord from the electrical outlet, and al-
low the unit to cool to room tempera-
ture before proceeding.
2. Remove the two Phillips head
screws, washers, and nylon spacers
securing the side glass (Figure 8).
3. Remove the side glass from the unit.
4. To reinstall, position the side glass
panel into place and install the nylon
spacers, washers, and Phillips head
screws.
Top Glass Replacement
1. Turn the unit OFF, unplug the power
cord from the electrical outlet, and al-
low the unit to cool to room tempera-
ture before proceeding.
2. Remove the top Phillips head
screws, washers, and nylon spacers
securing the top glass (Figure 10).
3. Remove the top glass from the unit.
4. To reinstall, position the top glass
panel into place and install the nylon
spacers, washers, and Phillips head
screws.
Figure 10. Top Glass Replacement
(DCH-320 Shown)
Phillip HD
Screws
Washers
Nylon Spacer
Nylon
Spacer

10
®
P/N 1012041 Rev E 08/23
Display Codes
This section describes the di󰀨erent display codes and their meanings.
TEMP
UP
TEMP
DOWN
TEMP
SCALE
F
C
O
O
“LO” ashes during the initial warm up period. The unit
continues to display this code until the unit reaches the
setpoint temperature. When the unit reaches the setpoint
temperature, it displays the setpoint temperature.
This gure shows an example setpoint temperature of
200° F displayed on the console.
“HI” ashes if the actual cabinet temperature exceeds the
setpoint temperature or if the thermistor has shorted.
NOTE: The thermistor should be 100k ohm +/- 2% at room
temperature.
“OPEN” ashes if the thermistor is OPEN or disconnected.
The unit will not call for heat.
NOTE: The thermistor should be 100k ohms +/- 2% at
room temperature.
“PO” In 120 VAC units, this code ashes if the supply volt-
age is below 100 VAC or above 135 VAC. In 220/240 VAC
units, this code ashes if the supply voltage is below 190
VAC or above 265 VAC.
NOTE: If voltage is within normal ranges, then the
Control Board is faulty.
To reset a unit in this state, the supply voltage must be
within acceptable limits and the unit must be turned o󰀨 for a
few seconds and then turned back on.

®
11
P/N 1012041 Rev E 08/23
Operations and Programming
IMPORTANT: All models of the DCH-
220 have a temperature range of
100°-165°F (38°-74°C) which is
below the safe holding tem-
perature for some foods. Only
non-potentially hazardous food
should be held in these units.
NOTICE: The Setpoint temperature is
the desired temperature setting.
The Indicated temperature is the
actual temperature inside the
cabinet. When the temperature
button is pressed and held, the
actual temperature is displayed;
when released, the setpoint
temperature is displayed.
1. Set the rocker switch (Figure 12) to
the ON position.
2. Press and hold both the TEMP UP
and TEMP DOWN buttons until the
display blinks.
3. When the Display “blinks”, press an
UP or DOWN ARROW key to reach
the desired set point temperature
and then let go. The new set point
temperature will now be active
(Figure 11).
4. The unit will reach the desired
temperature and humidity in 30-45
minutes.
5. Open the rear door and place the
serving table pan(s) into the unit
(Figure 13). Load the pan(s) with
food using tongs or similar utensil.
Close the door.
Figure 11. Control Panel - Key Pad
Figure 12. Controls
Figure 13. Loading Food (DCH-100
Shown)

12
®
P/N 1012041 Rev E 08/23
Troubleshooting
Problem Possible Cause Corrective Action
No heat and lights do not
turn on when power switch is
set to on.
Power cord is not plugged in. Plug the power cord into the appropriate outlet.
Circuit breaker is o󰀨 or has been tripped. Reset circuit breaker, contact your maintenance
person or Authorized Service Agency if it trips again.
No power at receptacle.
Contact your maintenance person or Authorized
Service Agency for service.
Inoperable power cord.
Inoperable power switch.
Loose, burnt, broken wiring in the circuit.
Inoperable Transformer. Contact your maintenance person or Authorized
Service agency for service.
Inoperable Control Board.
Display ashes “LO” and the
cabinet does not heat up.
Inoperable Solid State Relay.
Contact your maintenance person or Authorized
Service Agency for service.
Inoperable Control Board.
Inoperable Heater(s).
Loose, burnt, broken wiring in circuit.
Display ashes “HI” and the
cabinet does not heat up.
Inoperable Thermistor. Contact your maintenance person or Authorized
Service Agency for service.
Inoperable Control Board.
Display ashes “HI” and the
cabinet is very hot.
Solid State Relay contacts shorted
closed. Contact your maintenance person or Authorized
Service Agency for service.
Inoperable Control Board.
Display ashes “OPEN” and
the cabinet does not heat up.
Thermistor is disconnected or open. Re-secure the Thermistor onto the Control Board.
If this problem persists, contact your maintenance
person or Authorized Service Agency for service.
Inoperable Control Board.
Display ashes “PO” and the
cabinet does not heat up. Inoperable Control Board. Contact your maintenance person or Authorized Service Agency for service.
Product dries out quickly.
Setpoint temperature is set too high. Lower the Setpoint temperature.
Incorrect wattage halogen bulb(s) being
used. Use only 100 watt halogen bulb(s).
Halogen Bulb(s) do not light
up.
Bulb(s) burnt out. Replace bulb(s)
Bulb(s) not seated properly into spring
loaded sockets.
Remove and reinstall bulb(s) so that the ends snap
into the socket(s).
Inoperable Resistor Assembly.
Contact your maintenance person or Authorized
Service Agency for service.
Loose, burnt, or broken wiring in Circuit.
Inoperable Bulb Sockets(s).
WARNING
To avoid possible personal injury and/or damage to the unit, inspection, test and repair of electrical equipment should be
performed by qualied service personnel. The unit should be unplugged when servicing.

®
13
P/N 1012041 Rev E 08/23
Item
No. Part # Description Qty.
17002381 Lamp Housing Assembly (120V)
Kit 1
0011618 Lamp Housing Assembly (230V) 1
2 0024032 Control Panel Weldment 1
3 2100387 Track Door, Upper 1
42100184 Track Door, Lower 1
50502865 Bracket, Lamp Housing 2
60502866 Cover, Lamp Housing Brkt 2
70800224 Lamp Guard 1
84030324 Heating Element (120V) 1
4030325 Heating Element (230V) 1
90010706 Resistor Assembly (120V) 1
0010644 Resistor Assembly (230V) 1
10 0701081 Wire Set 1
11 0400119 Bushing, Shorty 4
12 0400111 Bushing, Shorty, 1/2” 1
13 4060304 Terminal Block, 3-Wire 1
14 306P156* 6-32 x .38 LG RD HD PH S.S 4
15 5040030 Insulation, CERA BLANKET 1
16 308P157* Screw, Tap, 8-32 x 3/8” LG 1
17 308P203*Screw, 8-32 x 3/8”, w,int. tooth
washer 16
18 306P123*Screw, Mach #6-32 x 7/8” SL-
RNDHD 2
19 306P101* Nut, Hex, #06-32 St.Stl 2
20 0200156 Gasket, Strip 1
21 0200191 Gasket 2
22 0200192 Gasket, Strip 1
23 21800-0120 Hole Plug - 7/8” 2
24 2140101 Adhesive/Sealant - RTVAR -
25 3250223 Screw, SOC HD, 1/4-20 x 3/8 LG 2
26 7000882 Rocker Switch Replacement Kit 1
27 1001037 Label, Control Panel 1
28 1000900 Label, Service 1
29 1001213 Label - Shock Hazard 1
30 4070052 Assy - PCB, Control temp Display
38°-74°C / 100°-165°F 1
31 0024115 Mounting Plate 1
32 4010199 Transformer (120V) 1
4010187 Transformer (230V) 1
33 4050231 Relay, Zero Cross, Solid State
50A 1
34 304P105*Nut, hex “KEPS” #4-40 4
35 306P130 Nut, hex “KEPS #06-32 Steel,
Zinc Plated 4
36 308P143*Nut, Hex “KEPS” #8-32 2
Item
No. Part # Description Qty.
37 7000369 Thermistor Replacement Kit 1
38 0700451 Power Cord (120V) (Not Shown) 1
0700453 Power Cord (230V) (Not Shown) 1
39 0400354 90° Strain Relief (Not Shown) 1
40 4060252 Quartz Halogen 100w 2
41 4060189 Lamp Holder 4
42 0800230 Support Rod 1
* Available in packages of 10 (Ten)
NOTE
Use only genuine Antunes replacement parts in this display
cabinet. Use of parts other than those supplied by the
manufacturer will void the warranty.
Replacement Parts
Parts List

14
®
P/N 1012041 Rev E 08/23
Replacement Parts
Exploded Diagram 1
43
46
57
44
50
49
48
45
49
50
55
53
52
51
58 59 60
59
60
47
56
54
56
NOTE: 120V & 230V share same
components as shown
NOTE: Mirrored side
of glass panel
goes towards
food and the
customer.

®
15
P/N 1012041 Rev E 08/23
Replacement Parts
Exploded Diagram 2
Detail A
See Detail A
2
14
14
30 32
37
34
13
19
31 33
36
11
18
35
26
16
28
29
27
1
10
6
5
21
22
15
21
3
8
42
23
25
20
4
17
640
41
41
41

16
®
P/N 1012041 Rev E 08/23
Wiring Diagram
DCH-220 (120V) SQ
DCH-220 120V

®
17
P/N 1012041 Rev E 08/23
Wiring Diagram
DCH-220 (230V) SQ
DCH-220 230V

Limited Warranty
Equipment manufactured by Antunes has been constructed of the finest materials available and manufactured
to high quality standards. These units are warranted to be free from mechanical and electrical defects for a
period of one year from date of purchase or 18 months from shipment from factory, whichever occurs first,
under normal use and service, and when installed in accordance with manufacturer’s recommendations.
To insure continued proper operation of the units, follow the maintenance procedure outlined in the Owner’s
Manual.
1. This warranty does not cover cost of installation, defects caused by improper storage or handling prior to placing
of the Equipment. This warranty does not include overtime charges or work done by unauthorized service
agencies or personnel. This warranty does not cover normal maintenance, calibration, or regular adjustments
as specified in operating and maintenance instructions of this manual, and/or labor involved in moving adjacent
objects to gain access to the Equipment. This warranty does not cover consumable items such as gaskets
and light bulbs, nor does it cover water contaminant problems such as foreign material in water lines or inside
solenoid valves. It does not cover water pressure problems or failures resulting from improper/incorrect voltage
supply.
For the first 90 (ninety) days after installation (in the U.S. ONLY), the unit will be repaired in-store (subject to the
terms of the limited warranty) by our Authorized Service Agency at no charge for parts and non-overtime labor.
Travel time and mileage charges in excess of 2 hours (100 miles roundtrip) from the nearest Authorized Service
Agency is not covered under this warranty and is the responsibility of the end user.
2. Antunes reserves the right to make changes in design or add any improvements on any product. The right is al-
ways reserved to modify equipment because of factors beyond our control and government regulations. Chang-
es to update equipment do not constitute a warranty charge.
3. If shipment is damaged in transit, the purchaser should make a claim directly upon the carrier. Careful inspec-
tion should be made of the shipment as soon as it arrives and visible damage should be noted upon the carrier’s
receipt. Damage should be reported to the carrier. This damage is not covered under this warranty.
4. Warranty charges do not include freight or foreign, excise, municipal or other sales or use taxes. All such freight
and taxes are the responsibility of the purchaser.
5. This warranty is exclusive and is in lieu of all other warranties, expressed or implied, including any implied war-
ranty or merchantability or fitness for a particular purpose, each of which is hereby expressly disclaimed. The
remedies described above are exclusive and in no event shall Antunes be liable for special consequential or
incidental damages for the breach or delay in performance of this warranty.
The warranty does not extend to:
yDamages caused in shipment or damage as result of improper use.
yInstallation of electrical service.
yInstallation, calibration, or adjustment.
yNormal maintenance outlined in this manual.
yMalfunction resulting from improper service or maintenance.
yDamage caused by improper installation, abuse, or careless handling.
yDamage from moisture getting into electrical components.
yDamage from tampering with, removal of, or changing any preset control or safety device.
yDamage caused by parts or components not provided by Antunes
Corporate Headquarters
Carol Stream, IL, USA
Phone: [phone]
Toll Free: +1.800.253.2991
Fax: + 1.(630).784-1650
China Facility
Suzhou, China
Phone: [phone]
Fax: [phone]
India Facility
Chennai, India
Phone: [phone]
Fax: [phone]