APS iArmor User manual

Rev. 20220201
1
iArmor®
Customer Support: [email protected]
iArmor® by APS PART#: IA-S097&S098
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS
ARE PRESENT. READ INSTRUCTIONS CAREFULLY
BEFORE STARTING INSTALLATION. ASSISTANCE IS
RECOMMENDED. THANK YOU FOR CHOOSING OUR
PRODUCT!
*ROCKER PANEL MOUNT
*NO DRILLING / TRIMMING REQUIRED
Fastener Size Tightening Torque (ft-lbs) Required
6mm 6-7 X
8mm 16-18 √
10mm 31-32 X
12mm 56-58 X
14mm 92-94 X
Item QTY Description Item QTY Description
1# 2Driver/Passenger Front Mounting Brackets 6# 18 M8 Large Flat Washers
2# 4Driver/Passenger Center / Rear Mounting Brackets 7# 18 M8 Lock Washers
3# 6U Brackets 8# 6M8X1.25-55mm Carriage Bolts
4# 12 Spacers 9# 6 M8X1.25 Hex Nuts
5# 12 M8X1.25-30mm Hex Bolts
3 # 4 # 5 # 7# 8 # 9 #6 #

Rev. 20220201
2
iArmor®
Customer Support: [email protected]
Front PassengerDriver
1#
2#
1#
2#
2#2#

Rev. 20220201
3
iArmor®
Customer Support: [email protected]
STEP 1
Start the installation under the driver side of the vehicle. Deter-
mine Driver Side Front, Center and Rear Mounting Locations
(Figs 1 & 2).
The instruction here is for your reference only. We strongly
recommend the professional installer for best result. We are not
responsible for any damage caused by the installation.
(Fig 1) Driver Side Front Mounting Location
STEP 2
Attach the Driver Front Mounting Bracket to the body panel by
using (2) M8X1.25-30mm Hex Bolts, (2) M8 Large Flat Wash-
ers and (2) M8 lock washers. Don’t fully tighten at this time,
(Figs 3 & 4).
Remove Plastic Plugs (If
Equipped) Or Hex Bolts
From Threaded Holes
(Fig 2) Driver Side Center/Rear Mounting Location
Front
Front
(Fig 3) Driver Front Mounting Bracket Installation
(2) M8X1.25-30mm Hex Bolts
(2) M8 Lock Washers
(2) M8 Large Flat Washers
(Fig 4) Driver Front Mounting Bracket Installed
STEP 3
Repeat Step 2 to install the remaining driver side center and
rear mounting brackets (Fig 5).
Note: Driver/Passenger Center and Rear Mounting Brack-
ets are universal.
Front

Rev. 20220201
4
iArmor®
Customer Support: [email protected]
(Fig 5) Driver Center/Rear Mounting Bracket Installed
STEP 6
Move to the passenger side of the vehicle. Repeat Steps 1-5 to
install the passenger side step bar.
Installation completed.
STEP 5
Properly level and adjust the Step Bar and fully tighten all hard-
ware.
STEP 4
Once all (3) driver side mounting brackets are installed, select
and attach the Driver Side Step Bar onto the Mounting Brackets
with (3) U Brackets, (6) Spacers, (3) M8X1.25-55mm Carriage
Bolts, (3) M8 Large Flat Washers, (3) M8 Lock Washers and (3)
M8X1.25 Hex Nuts (Fig 6). Do not fully tighten hardware at this
time.
Attention
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
In order to protect your bars/boards, please use only mild soap/non-abrasive products for cleaning.
NOTE: Torque all M8 X1.25-55mm Car-
riage Bolts to 16~18 Ibs-ft. Don't over
tighten, or the aluminum square bars
will be damaged by the brackets.
(Fig 6) Driver Side Step Bar Installation
Front
M8X1.25-55mm
Carriage Bolt
U Bracket
Spacers
M8 Large Flat Washer
M8 Lock washer
M8X1.25 Hex Nut