APS iBoard IB-R934 User manual

Customer Support: [email protected]
Rev. 20211001
1
iBoard
®
iBoard® by APS PART#: IB-R934
READ INSTRUCTIONS CAREFULLY BEFORE START ING
INSTALLATION. REMOVE CONTENTS FROM BOX AND
VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS
RECOMMENDED.
*ROCKER PANEL MOUNT
*NO DRILLING REQUIRED
Item QTY Description Item QTY Description
1# 2Driver/Passenger Front Mounting Brackets 4# 12 M6X1-20mm Square Head Bolts
2# 4Mounting Brackets 5# 12 M6 Large Flat Washers
3# 12 M8X1.25-20mm Hex Bolts 6# 12 M6 Nylon Lock Nuts
Fastener Size Tightening Torque (ft-lbs) Required
6mm 6-7 √
8mm 16-18 √
10mm 31-32 X
12mm 56-58 X
14mm 92-94 X
3 # 6 #
5 #
4 #

Customer Support: [email protected]
Rev. 20211001
2
iBoard
®
PassengerDriver Front
1# 1#
2#
2#
2#
2#

Customer Support: [email protected]
Rev. 20211001
3
iBoard
®
STEP 1
Start installation at the driver side of the vehicle.
Locate the (3) factory mounting hole locations on the underside
of vehicle rocker panel. Attach Driver Front Mounting Bracket to
the first set of mount holes closest to the front of vehicle with
(2) M8X1.25-20mm Hex Bolts. Don’t fully tighten at this time,
(Fig 1).
Note: The (2) Front Mounting Brackets are different with (4)
Center and Rear Mounting Brackets.
STEP 2
Move to the Center & Rear mounting locations. Repeat Step 1
to install Center & Rear Mounting Brackets. Do not fully tighten
at this time, (Fig 2).
STEP 3
Select a Running Board. Slip (3) M6x1-20mm Square Head
Bolts into each bottom channel (Fig 3). Carefully position the
Running Board onto the (3) Mounting Brackets.
IMPORTANT: Do not slide the Running Board on the Brackets
or the bottom surface of the board will be damaged. Attach the
Running Board to each Mounting Bracket with (2) M6X1-20mm
Square Head Bolts, (2) M6 Large Flat Washers and (2) M6
Nylon Lock Nuts (Fig 4). Do not fully tighten at this time.
(Fig 1) Driver Front Mounting Bracket (DFM) Installation
(2) M8X1.25-20mm Hex Bolts
(Fig 2) Driver Center & Rear Mounting Brackets Installation
(2) M8X1.25-20mm Hex Bolts
(Fig 3) Slip M6X1-20mm Square Head Bolts Into
The Bottom Channels
M6X1-20mm Square Head Bolts
(Fig 4) Running Board Installed Onto Mounting Bracket
(2) M6X1-20mm Square Head Bolts
(2) M6 Large Flat Washers
(2) M6 Nylon Lock Nuts

Customer Support: [email protected]
Rev. 20211001
4
iBoard
®
STEP 5
Repeat Steps 1-4 for the other side Running Board installation.
The installation is completed.
Attention
Do periodic inspections to the installation to make
sure that all hardware is secure and tight.
In order to protect your bars/boards, please use only
mild soap/non-abrasive products for cleaning.
STEP 4
Level and adjust the Running Board and fully tighten all hard-
ware.
Important: Please follow the recommended Tightening Tor-
ques shown in the table on page 1. Don’t over tighten, or
the nuts/bolts will be damaged.