AQUAPHOR C126 User manual

Three way kitchen faucet model number C126 to be used with tap water and
filtered tap water with other purifiers, which are connected to incoming tap water.
1. Cap
2. Aerator
3-4. Small diameter layer
5. Large diameter layer
6. Spout
7. Wear ring
8. Seal
9. O-ring, 2 pieces
10. Seal
11. Allen screw
12. The body of the mixer
13. A cartridge for hot and cold water
14. Threaded bush
15. Decorative hood
16. Cover
17. Allen screw for mounting handles
18. Handle Large
19. Crane bush
20. Plastic sleeve
21. Small housing
22. Handle Small
23. Threaded rod
24. Screw nut
25. Gasket
26. Shaped collar
27. Flexible connection hoses for cold
and hot water
28. Flexible connection hose
for purified water
Demonstrated in figure 1.
Three way kitchen faucet model C126
Instruction manual

Hole for connection
of purified water
flexible hose
Hole for connection of hot water
flexible hose (colour – red)
Hole for connection of cold water
flexible hose (colour – blue)
Figure 2. Flexible hoses and threaded rod connecting
Technical Specifications
Maximum water pressure 0.63 MPa
Cold water temperature +4…+ 38 °C
Hot water temperature to 75 °C
Temperature of filtered water 4…+ 38 °C
Faucet assembly Weight 2.01 kg
Included in content
Faucet assembly 1 pc.
Flexible connection hoses for cold
and hot water (27), L = 600 mm, G1/2 " 2 pcs.
Flexible connection hose for purified water (28), L = 370 mm, G3/8 " 1 pc.
Threaded rod (23) 1 pc.
Screw nut (24) 1 pc.
Gasket (25) 1 pc.
Shaped collar (26) 1 pc.
Adapter for tube JG 1/4 " 1 pc.
Manual 1 pc.
Package 1 pc.
Installation
Please read these instructions before attempting to install the faucet.
1. Drill a hole in the sink (countertop) diameter of 35 mm.
2. Screw the flexible hoses into the holes (3 pcs.), located at the bottom of the faucet
body (12), guided by the colour designation liner and instructions in Figure 2. To
connect Water purifiers that use tube JG 1/4 ", use an adapter (included).
3. Screw threaded rod (23) to the internal thread of the faucet body (12).
4. Insert hoses and then the threaded rod (23) in the aperture of the kitchen sink.
5. From the bottom of the sink put on the gasket (25) and shaped collar (26) on
a threaded rod and screw on the screw nut (24).
6. Place the faucet in a comfortable position and tighten the screw nut (24) to the
end.
Recommendations for the Use and Care
●Wipe the product with a soft cloth dampened with soapy water.
●Do not use abrasive cleaners to clean the surfaces of the faucet, as well as
caustic chemicals and solvents.
●When using the product in areas with hard water or water with a high
mineral content it is recommended to prevent salt deposits on the faucet’s
surface.
●Rinse the aerator frequently.
Disposed of in accordance with environmental, sanitary and other requirements established
by national standards in the field of environmental protection.
Service life and warranty
Service Life – 5 years from the date of sale, the end of the life of a mixer should be
replaced. Mixer operation after the end of life can cause harm to the consumer's property
or other persons. The shelf life of the faucet prior to the start of operation - no more than
3 years from the production date specified in this sheet at a temperature of +5 to +38 °C
without breaking the package. Warranty period of operation of the faucet – 1 year from the
date of sale. Warranty in not valid if:
– The requirements specified in this manual are not followed;
– In violation of installation and setup of the rules set out in this manual;
– Manual is lost with the manufacturers date or sale the warranty is knolled.
Hole for threaded rod

Figure 3. Faucet assembly
Cold and hot
water outlet
Purified water outlet
Faucet base
Purified water tap
handle
Cold and hot water
tap handle
Technical Specifications
Maximum water pressure 0.63 MPa
Cold water temperature +4…+ 38 °C
Hot water temperature to 75 °C
Temperature of filtered water 4…+ 38 °C
Faucet assembly Weight 2.01 kg
Included in content
Faucet assembly 1 pc.
Flexible connection hoses for cold
and hot water (27), L = 600 mm, G1/2 " 2 pcs.
Flexible connection hose for purified water (28), L = 370 mm, G3/8 " 1 pc.
Threaded rod (23) 1 pc.
Screw nut (24) 1 pc.
Gasket (25) 1 pc.
Shaped collar (26) 1 pc.
Adapter for tube JG 1/4 " 1 pc.
Manual 1 pc.
Package 1 pc.
Installation
Please read these instructions before attempting to install the faucet.
1. Drill a hole in the sink (countertop) diameter of 35 mm.
2. Screw the flexible hoses into the holes (3 pcs.), located at the bottom of the faucet
body (12), guided by the colour designation liner and instructions in Figure 2. To
connect Water purifiers that use tube JG 1/4 ", use an adapter (included).
3. Screw threaded rod (23) to the internal thread of the faucet body (12).
4. Insert hoses and then the threaded rod (23) in the aperture of the kitchen sink.
5. From the bottom of the sink put on the gasket (25) and shaped collar (26) on
a threaded rod and screw on the screw nut (24).
6. Place the faucet in a comfortable position and tighten the screw nut (24) to the
end.
Recommendations for the Use and Care
●Wipe the product with a soft cloth dampened with soapy water.
●Do not use abrasive cleaners to clean the surfaces of the faucet, as well as
caustic chemicals and solvents.
●When using the product in areas with hard water or water with a high
mineral content it is recommended to prevent salt deposits on the faucet’s
surface.
●Rinse the aerator frequently.
Disposed of in accordance with environmental, sanitary and other requirements established
by national standards in the field of environmental protection.
Service life and warranty
Service Life – 5 years from the date of sale, the end of the life of a mixer should be
replaced. Mixer operation after the end of life can cause harm to the consumer's property
or other persons. The shelf life of the faucet prior to the start of operation - no more than
3 years from the production date specified in this sheet at a temperature of +5 to +38 °C
without breaking the package. Warranty period of operation of the faucet – 1 year from the
date of sale. Warranty in not valid if:
– The requirements specified in this manual are not followed;
– In violation of installation and setup of the rules set out in this manual;
– Manual is lost with the manufacturers date or sale the warranty is knolled.

The manufacturer is entitled to upgrade design of the faucet
without making a prior note in the certificate.
Date of manufacturing and quality control
Date of purchase / Retailer’s stamp
С126
Kitchen faucet is lead-free.
Technical Specifications
Maximum water pressure 0.63 MPa
Cold water temperature +4…+ 38 °C
Hot water temperature to 75 °C
Temperature of filtered water 4…+ 38 °C
Faucet assembly Weight 2.01 kg
Included in content
Faucet assembly 1 pc.
Flexible connection hoses for cold
and hot water (27), L = 600 mm, G1/2 " 2 pcs.
Flexible connection hose for purified water (28), L = 370 mm, G3/8 " 1 pc.
Threaded rod (23) 1 pc.
Screw nut (24) 1 pc.
Gasket (25) 1 pc.
Shaped collar (26) 1 pc.
Adapter for tube JG 1/4 " 1 pc.
Manual 1 pc.
Package 1 pc.
Installation
Please read these instructions before attempting to install the faucet.
1. Drill a hole in the sink (countertop) diameter of 35 mm.
2. Screw the flexible hoses into the holes (3 pcs.), located at the bottom of the faucet
body (12), guided by the colour designation liner and instructions in Figure 2. To
connect Water purifiers that use tube JG 1/4 ", use an adapter (included).
3. Screw threaded rod (23) to the internal thread of the faucet body (12).
4. Insert hoses and then the threaded rod (23) in the aperture of the kitchen sink.
5. From the bottom of the sink put on the gasket (25) and shaped collar (26) on
a threaded rod and screw on the screw nut (24).
6. Place the faucet in a comfortable position and tighten the screw nut (24) to the
end.
Recommendations for the Use and Care
●Wipe the product with a soft cloth dampened with soapy water.
●Do not use abrasive cleaners to clean the surfaces of the faucet, as well as
caustic chemicals and solvents.
●When using the product in areas with hard water or water with a high
mineral content it is recommended to prevent salt deposits on the faucet’s
surface.
●Rinse the aerator frequently.
Disposed of in accordance with environmental, sanitary and other requirements established
by national standards in the field of environmental protection.
Service life and warranty
Service Life – 5 years from the date of sale, the end of the life of a mixer should be
replaced. Mixer operation after the end of life can cause harm to the consumer's property
or other persons. The shelf life of the faucet prior to the start of operation - no more than
3 years from the production date specified in this sheet at a temperature of +5 to +38 °C
without breaking the package. Warranty period of operation of the faucet – 1 year from the
date of sale. Warranty in not valid if:
– The requirements specified in this manual are not followed;
– In violation of installation and setup of the rules set out in this manual;
– Manual is lost with the manufacturers date or sale the warranty is knolled.
Manufacturer:
Westaqua-Invest OÜ,
L. Tolstoi 2A, Sillamäe,
40231, Eesti.
www.aquaphor.com