Argos 033 0501 Series User manual

Assembly Instructions -Please keep for future reference
Width - 89cm
TV Unit
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08450613967
Please turn to back page for important information when contacting Customer Helpline.
Dimensions
Depth - 38.8cm
Height - 43cm
Rev A - 12.05.10
033 xx 0501
PDF processed with CutePDF evaluation edition www.CutePDF.com

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 4.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergants, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furnture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
when assembly complete.
Do Not dispose of packaging
until assembly complete.

Please check you have all the panels listed below
Components -Panels
Left hand end (37x37cm) Right hand end (37x37cm)
Code - Code -
2
Important - Thick lines indicate finished edges
7519 7520
Top (89x38.8cm)
Backpanel (37x30.4cm)
Code - 7527
Shelf (54.6x36.8cm)
Code - 7525
Bottom (89x38.8cm)
Door
(36.4x32.2cm)
Code -
7523
7522
7521
Code - Code -
Right side (37x37cm)
Code - 7524
Shelf (29.4x34.8cm)
Code - 7526

3
Components -Exploded View
Important - Thick lines indicate finished edges
7523
7519
7526
7522
7525
7521
7524
7520
7527

70 80 90 100 110 120
010 20 30 40 50 60
mm
130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Components-Fittings
Note: The quantities below are the correct amount to complete the assembly, In some case more fittings
may be supplied than are required.
Tools required
If you have damaged or missing components, call the
Customer Helpline: 0845 0613967 Please turn to back page
for important information when contacting Customer Helpline.
4
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
Large cam x 14 - Code 760001103 Metal dowel x 14 - Code 760003004 12mm screw x 4 - Code 690001008
25mm screw x 2 - Code 690001021
Handle x 1
Code 644396000
ABD
GJ
L
45mm screw x 6 - Code 690001075
K
N
22mm screw x 5 - Code 690001018
Glide feet x 5
Code 720001904
Bradawl
M
Wooden dowel x 6
Code 770001006
O
Straight arm 26mm
hinge x 2
Code 652001128
P
Hingeplate x 2
Code 653006000

Step 1
Assembly Instructions
5
Fittings you will need for this step:
B
B
B
B
B
(x6)
Note: Insert metal
dowels as far as
shown by arrows.
Do not over tighten.
B
Note: Ensure cam
arrow points towards
the edge with hole.
A
Fittings you will need for this step:
A
(x8)
Fitting dowels to top
panel
Step 2
Fitting cams to
shelves
Large
7521
B
A
A
A
A
7525
B
B
A
A
A
A
7526

Step 3
Assembly Instructions
6
Fittings you will need for this step:
B
B
(x4)
Note: Insert metal
dowels as far as
shown by arrows.
Do not over tighten.
B
Note: Ensure cam
arrow points towards
the edge with hole.
A
Fittings you will need for this step:
A
(x4)
Fitting cams, metal
dowels and wooden
dowels to left and
right hand ends
Step 4
Large
7519
B
A
Fitting hingeplates to
left hand end panel
P
(x2)
A
B
Notch in Hingeplate points
towards front finished edge.
P
Front
finished
edge
P
M
M
M
(x4)
Use a hammer to
knock in wooden dowels
into inner holes.
M
M
P
7519
B
7520
A
A
B
M
M

Step 5
Assembly Instructions
7
Fittings you will need for this step:
B
B
(x2)
Note: Insert metal
dowels as far as
shown by arrows.
Do not over tighten.
B
Note: Ensure cam
arrow points towards
the edge with hole.
A
A
(x2)
Fitting cams, metal
dowels and wooden
dowels to division
Step 6
Large
7524
B
A
A
B
M
M
M
(x2)
Use a hammer to
knock in wooden dowels
into inner holes.
M
M
B
7524
B
Important:
We recommend you
do this on the packaging
the unit came in to
protect your floor.
Note: Insert metal
dowels as far as
shown by arrows.
Do not over tighten.
B
Turn division over
to insert metal dowels
on the opposite side
of division
B
7524
7524
Fittings you will need for this step:
B
(x2)

Step 7
Assembly Instructions
8
Fittings you will need for this step:
Attach hinges and
handles to door
a: Insert hinges
into holes, ensure
the hinge is straight
(90 degree angle).
b: Before securing the
hinges , we recommend
you pre - mark the doors
using a bradawl.
Important: (x2)
J
G
(x1)
(x4)
D
(x2)
O
O
O
90
O
98
O
O
7523
O
Bradawl
O
D
c: Secure hinges to
doors
using screws .
O
7523
D
d: Secure handle to
doors
using screws .
J
G
G
G
J
O
O
a:
b:
c:
d:
D
D
O
O
D
D
7523
D
O
7523
7523
7523

Insert dowels in left
into cams in
small shelf .
Then lock.
B
A
Tu r n cam 180 degrees
to lock
A
9
Attach small shelf
to left hand end and
division
Assembly Instructions
Step 8
Step 9
7519
7524
7526
7519
7526
Insert dowels in
division into
cams in small shelf
.
Then lock.
B
A
7524
7526
Locate cams in large
shelf onto dowels
in division .
Then lock.
B
A
7525
7524
7524
7525
7520
Tu r n cam 180 degrees
to lock
A
Insert dowels in right
20 into cams in
large shelf .
Then lock.
B
A
7520
7525
Attach large shelf
to division and right
hand end
Groove
Cam holes to
underside
Cam holes to
underside