Argos HOME New Pagnell Deep 3+2 Chest 610/8793 User manual

Assembly Instructions -Please keep for future reference 610/8793
Dimensions
Width - 76.5cm
Depth - 40.5cm
Height - 82m
Important - Please read these instructions fully before starting assembly
Version 1 Date: 10/11/16
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
New Pagnell Deep 3+2 Chest
620/5861
619/5139

1
Safety and Care Advice
Important –Please read these instructions fully before startingassembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Do not use this item if any
components are missing or
damaged.
• Parts of the assembly will be
easier with 2 people.
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
Handy Hints
• Argos Ltd. MK9 2 NW. • This product is intended for
children in the age range of
7-12 years.
• Maximum load: 25 kgs.
• Assembly of this product must
be carried out by a competent
adult.
IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE

Components -Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline:
Argos = 0345 6400800
2
Left side panel
(80.4 x 38cm)
1
Small drawer left
panel x 4
(34 x 11.5cm)
9Small drawer right
panel x 4
(34 x 11.5cm)
10
Large drawer left
panel (34 x 24cm)
11 Large drawer right
panel (34 x 24cm)
12
Left drawer front
panel (36 x 14.4cm)
13 Right drawer front
panel (36 x 14.4cm)
14
Middle drawer front panel
x 2 (72.3 x 14.4cm)
15
Large drawer support
(32.7 x 6cm)
20
Small drawer bottom
panel x 2 (33.1 x 33.6cm)
21
Large drawer bottom
panel x 3 (70.7 x 33.6cm)
22
Back panel (77 x 75.8cm)
23
Large drawer front panel
(72.3 x 28.7cm)
16
Small drawer back panel
x 2 (32.2 x 11.5cm)
17
Middle drawer back panel
x 2 (69.8 x 11.5cm)
18
Large drawer back panel
(69.8 x 24cm)
19
Right side panel (80.4 x 38cm)
2
Top support (36.2 x 13.6cm)
3
Middle panel (73 x 11cm)4
Back bottom panel (73 x 11cm)5
Front bottom panel (73 x 11cm)6
Front panel (73 x 4.5cm)
7
Top panel (76.2 x 40cm)
8
Pilot holes for guidance only
Finished
front edge
Pilot holes for guidance only
Pilot holes for guidance only
Drill holes
near edge

3
Please check you have all the fittings listed below
50mm Screw x 2
Ruler - Use this ruler to help correctly identify the screws
Tools required
A
Nail x 18
E
30mm Screw x 22
B
12mm Screw x 10
H
39mm Locking pin x 33
C
14.5mm Screw x 8
I
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
15mm Locking nut x 12
F
30mm Dowel x 9
12mm Locking nut x 21
D
12mm Screw x 30
Wall plug x 2
N
Runner x 10
K
G
Plastic support x 3
J
Components - Fittings
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or glue)
The screws length is measured from the head to the point (30mm screw shown).
M
L
(Screws are included in
the runners bag)
Wall strap x 2
(This screw is
included in the
wall strap bag)
x 2
7mm Suitable drill bit
(for use with wall plug)
Pencil
Glue x 1
O

Right side panel .
4
Assembly Instructions
Step 1
Continued on next page.Continued on next page.
Position Runners in
front edge of the Right
side panel .
Runners on the Right
side panel .
Slide top of the Runners
Use screws to fix the
back.
Attaching runners
a:
2
2
2
K
K
K
L
Slide top of Runners
shown using Screws .
forward and fix as
b:
K
L
Note: The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
a:
b:
Insert Dowel into the
D
Screw Locking pins into
the
Right side panel .
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
C
2
C
2
2
Pilot holes for
runner position
K
K
K
K
K
L
L
L
L
L
L
L
L
L
L
L
L
D
K
K
K
C
C
C
L
K
Middle hole
2
1.7cm
B
A
L
K
LMiddle hole 2
Finished front edge

Assembly Instructions
Step - continued1
back.
c:
Position Runners
in front edge of the Left
side panel .
1
K
Slide top of the Runners
K
Runners on the Left
side panel .
Use screws to fix the
L
1
Slide top of Runners
shown using Screws .
forward and fix as
d:
K
L
Note: The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
c:
d:
5
Continued on next page.
Insert Dowel into the
Right side panel .
D
1
Screw Locking pins into
the
Right side panel .
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
C
K
1
1
1
C
Pilot holes for
runner position
D
K
K
K
K
L
L
L
L
L
L
L
L
L
L
L
L
C
C
K
K
K
K
L
K
Middle hole 1
1.7cm
C
L
K
L
Middle hole
1
Finished front edge

g: Turn the Top support
upside down, repeat
e and f with remaining
Runner and Screws .
Assembly Instructions
6
back.
e: Position Runner in
front edge of the Top
support .
K
Slide top of the Runner
K
Runner on the Top
support .
Use screw to fix the
K
L
3
Note: The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
e:
f:
g:
Step - continued1
shown using Screws .
forward and fix as
f: Slide top of Runner
K
L
Insert Dowel into the
Top support .
D
3
3
3
K
K
L
L
K
K
L
L
D
L
L
K L
Pilot holes for
runner position
Pilot holes for
runner position
3
3
3
3
Finished
front edge
Finished front edge
L
K
Middle hole 3
1.7cm
L
K
L
Middle hole
3

a: Insert Dowels into
the Back bottom panel
.
b: Use Screws to fix
Front panel onto the
Front bottom panel .
Continued on next page.
Assembly Instructions
7
J
I
I
7
6
b:
I
Step 2
a:
b:
Step 3
Attaching bottom panel
and middle panel
D
5
b: lnsert Dowels into the
Middle panel .
Use Screws to fix the
Top support onto the
Middle
panel .
4
D
A
3
4
a: Use Screws to fix
Plastic supports onto
the Front panel .
Attaching plastic
supports
J
I
7
a:
I
J
J
J
I
I
I
D
D
D
D
A
A
D
D
I
I
7
76
5
4
3

Assembly Instructions
8
Step - continued3
d: Carefully locate the
Front bottom panel
onto the Left side panel
.
Insert Locking nut into
the Front bottom panel
.
Use a screwdriver to turn
Locking nut clockwise
to lock.
6
6
1
F
F
d:
c: Carefully locate the
Middle panel onto the
Left side panel .
Insert Locking nut into
the
Middle panel .
Use a screwdriver to turn
Locking nut clockwise
to lock.
4
4
1
F
F
c:
F
F
F
F
4
1
1
6
Unfinished
back edge
Unfinished
back edge

Assembly Instructions
9
Step - continued3
e: Carefully locate the
Back bottom panel
onto the Left side panel
.
5
5
1
Insert Locking nut into
the Back bottom panel
.
F
Use a screwdriver to turn
Locking nut clockwise
to lock.
F
e:
Step 4
Carefully locate the
Right side panel onto
the unit.
2
Insert 3 Locking nuts
into the unit.
F
Use a screwdriver to turn
Locking nuts clockwise
to lock.
F
Attaching right side
panel
F
F
F
F
F
5
5
4
2
6
1
Unfinished
back edge
Unfinished
back edge