Argos 332/5476 User manual

MADE IN
BRITAIN
Dimensions
Width - 119.5cm
Depth - 39.5cm
Height - 35.5cm
Retro Pedestal - TV Unit
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 01/12/14
Important - Please read these instructions fully before starting assembly
ALR3119
332/5476

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 20kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
12
5
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Drawer Back (W463-124)
(463 x 124mm)
Drawer Base (T474-367)
(474 x 367mm)
Left Drawer
Side (W370-124LH)
(370 x 124mm)
Right Drawer
Side (W370-124RH)
(370 x 124mm)
Top (DF1088)
(1194 x 392mm)
Base (DF1092)
(1194 x 392mm)
Left Side (DF1089)
(235 x 390mm)
Left Divider (DF1090)
(235 x 390mm)
Right Divider (DF1880)
(235 x 390mm)
Right Side (DF1091)
(235 x 390mm)
4
3
6
7Drawer Front (DF1094)
(489 x 229mm)
8 9 10
11
12
13
14 Back (X1186-261)
(1113 x 261mm)
Rail (DF1095)
(1075 x 60mm)
Shelf (DF1482)
(521 x 389mm)

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A
D E F
G H I
L
C
Small locking
nut (F3) x 2
B
Nail (F51) x 20
M
J
9mm Screw (F74) x 2
K
9mm Screw (F73) x 4
Drawer runner (F1004) x 2
Knock-in Peg (F171GY) x 4
Large locking
nut (F900) x 8
Metal dowel (F901) x 10
Wooden dowel (F22) x 8
Wedgefix (F639) x 4
Rule Scissors Hammer Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(do not use for
fitting screws)
Allen Key (F36) x 1 Foot (D3084) x 4
50mm Screw (F49) x 12
O
N
Shelf stud (F110) x 4
25mm Screw (F281) x 5

8
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
A
B
A
B
B
BB
910
Step 2
Prepare the drawer
front
Screw 2 metal dowels
into the drawer front .
Note: Tighten the metal
dowels up fully against
the panels.
A
8
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
B
9
10
Attach the drawer
sides to the drawer
front
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
9
10
8
B
B
9
10
10
A
A
8
9
80%
x 2

8
Assembly Instructions
5
Step 4
F
F
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
12
9 10
8
11
9 10
12
11
11
F
9 10
Step 6
Fit the wedgefixes
Turn the drawer
assembly over and slide
4 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
L
F
F
L
L
L
LL
12
9
11
9
10
12
10

D
D
Assembly Instructions
6
Step 7
Prepare the top
Screw 8 metal dowels
into the top .
A
3
Finished
front edge
A
A
A
A
A
A
A
A
Step 8
3
Finished
front edge
I
O
Prepare the left
divider
a: Tap 2 wooden
dowels into the left
divider .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Place a runner on the
left divider as shown.
Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left divider .
Insert 2 large locking
nuts into the left
divider .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
2
D
a:
b:
10mm
D
O
2
I
O
I
2
2
C
I
O
I
C
C
Finished
front edge
Finished
front edge
C
2
2

Finished
front edge
Finished
front edge D
D
Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 9
Step 10
Fit the left divider to
the top
Push the left divider
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the left divider .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
3
2
C
C
2
A
C
Prepare the left side
a: Tap 2 wooden
dowels into the left
side .
Place a runner on the
left side as shown.
Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
Insert 2 large locking
nuts into the left side
. .
1
D
O
1
I
O
I
1
1
C
Finished
front edge
I
O
a:
b:
I
O
I
C
C
3
2
1
1

Finished
front edge
Finished
front edge
Assembly Instructions
8
Step 11
Step 12
D
D
Finished
front edge
C
C
Prepare the right side
Tap 2 wooden dowels
into the right side .
Insert 2 large locking
nuts into the right
side .
4
D
4
C
4
Left Side (DF1089)
(235 x 390mm)
Left Divider (DF1090)
(235 x 390mm)
Fit the left side
Push the left side
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the left side .
3
1
C
1
3
1
Fit the right side
Push the right side
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the right side .
3
4
C
4
Step 13
3
4

Finished
front edge
Finished
front edge
Assembly Instructions
9
Step 14
Step 15
Finished
front edge D
D
5
C
C
Prepare the right
divider
Tap 2 wooden dowels
into the right divider .
Insert 2 large locking
nuts into the right
divider .
5
D
5
C
Fit the right divider
Push the right divider
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the right divider .
Step 16
3
5
C
5
3
5
5
Fit the base
Attach the base to
the left side , the left
divider , the right side
. and the right divider
. using 8 screws
and tighten them using
the allen key .
1
6
4
5
2
G
M
G
G
G
M
G
G
GG
G
1
6
4
5
2