Argos Amelie 247/9873 User manual

If you need help or have damaged or missing parts, call the
Important - Please read these instructions fully before starting assembly
Dimensions
Width - 93 cm
Depth - 57 cm
Height - 160 cm
Baby Amelie-
Assembly Instructions 247/9873 - Please keep for future reference
Customer Helpline: 08456 400 800
2 Door Robe
Issue 1 - 02/05/14

Note:if required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
.Check you have all the
components and tools listed on
pages 2 and 3.
.Remove all fittings from the
plastic bags and separate them
into their groups.
.Keep children and animals
away from the work area, small
parts could choke if swallowed.
.Make sure you have enough
space to layout the parts before
starting.
.Do not stand or put weight on
the product, this could cause
damage.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
This product has been produced
from natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
.
.Assemble the item as close
to its final position (in the same
room) as possible.
.Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Care and maintenance
Avoid placing the furniture in
Use an appropriate furniture .From time to time check
that there are no loose
screws on this unit.
.This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.
.
.
direct sunlight as this will cause
the timber to prematurely age.
polish for natural wood
furniture and a dry cloth to
clean the product.
Safety and Care Advice
Important -
.
.
Please read these instructions fully before starting assembly

2
Components - Panels
Please check you have all the panels listed below
8Bottom frame x 1 (76x6 cm)
Back panel x 2 (133.5x39.4 cm)
Drawer right side x 1 (40x10.5 cm)
9Back rail x 1 (76x4.5 cm)
Drawer left side x 1 (40x10.5 cm)
12
11 23
24 "H" profile x 1 (130.6x1.7 cm)
22 Large back rail x 1 (76x9 cm)

3
Components - Fittings If you have damaged or missing components,
call the Customer Helpline: 08456 400 800
Note:The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Phillips screwdriver
(medium & large)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
Tools required
Wooden dowel x 36 30 mm Screw x 12 12 mm Screw x 6
12 mm Screw x 4 Right runner x 2
Nail x 30
Knob x 4 20 mm Bolt x 4
Please check you have all the fittings listed below
A B C
FED
G H I
K
J
Left runner x 2
Locking nut x 15Metal dowel x 15
30 mm Screw x 20
L
Wall strap x 1 Washer x 1
NM O
P
S
QR
60 mm Screw x 6 Hinge x 4 Hinge plate x 4
12 mm Screw x 23
Rail support x 2
T
Plastic Wedge x 2
E2
E1 F1
F2

4
Assembly Instructions
A
Step 1
Fitting Wooden Dowels:
Insert dowels into holes in
the indicated parts.
G
Fitting metal dowel
Screw metal dowel into top
frame and side panels
and .
2
3
Note: Insert metal
dowels as far as
shown.
Do not over tighten.
1
2
8
22
18
2
O
R
Fixing hinge plates:
Fix hinge plates in the pre
drilled holes on side panels
and using screws as
shown.
3
2
O
S
Fixing hanging holder:
Fix rail support in the pre
drilled holes on side panels
and using screws .
3
19

5
Assembly Instructions
Step 2
Step 3
L
Parts , , , , and
are labelled for easier
identification.
Attach left side panel to left
front foot and left back foot
using screws .
Attach right side panel to
right front foot and right
back foot using screws .
L
3
20
O
Q
Fixing hinge:
Fix hinge in the pre drilled
holes on doors and using
screws .
Fix knob using bolts .
21
JK
Attention:
Make sure side
panels are correctly
aligned and in flush
to the top of the feet
prior to fixing, as
shown.
2345 6
7

6
Assembly Instructions
Step 4
2
C
E
Fixing runners:
Fix runners and in the pre
drilled holes on side panel
and using screws .
2
3
F
3
2
Attention:
Make sure runners
are positioned as
shown.

Assembly Instructions
Step 5
Step 6
Assembly the cabinet
Fit base panel and front rail
to the right side panel as
shown.
Insert 4 locking nuts into
base panel and front rail
where shown.
Use a screwdriver to turn
locking nuts clockwise to
lock.
Do not over tighten.
H
16
7
3
3
8
18
22
H
a) Fit bottom frame and
back rail to the right side
panel as shown.
Insert 2 locking nuts into
bottom frame and back rail
where shown.
Use a screwdriver to turn
locking nuts clockwise to
lock.
Do not over tighten.
b) Attach large back rail in
the right side using screws
.
H
8
9
3
22
3
B
16
H
8
9
18
18
3

Assembly Instructions
Step 7
Step 8
8
H
a) Fit left side panel to the
bottom frame , back rail ,
front rail , base panel and
large back rail .
Make sure dowels are fitted
into their holes at the same
time.
Insert 6 locking nuts into
bottom frame and back rail
, front rail and base panel
, where shown.
Use a screwdriver to turn
locking nuts clockwise to
lock.
Do not over tighten.
b) Attach large back rail in
the left side using screws .
H
8
9
Carefully, lay down the cabinet.
Attach top panel to side
panels and using screws
.
P
23
1
3
8
16
22
18
18
16
22
3B
1
2
89
18 16
22

Assembly Instructions
Step 9
Step 10
H
Attaching top frame
Fit top frame to the top
panel .
Insert 3 locking nuts into top
panel where shown.
Use a screwdriver to turn
locking nuts clockwise to
lock.
Do not over tighten.
H
1
I
Fixing back panel
With help, carefully turn the
cabinet upright.
Fix back panels within
rebates using nails .
Ensure H profile is in place
before nailing as shown.
Important: Cabinet
MUST be 'square' when
back is attached.
Make sure finished side
of back panel is facing
inside.
1523
9
1
24
23 23
1
2
24
1
19
3
2