Argos 833/2536 User manual

Tall Storage Unit
Assembly Instructions -
Please keep for future reference 833/2536
Dimensions
Depth - 30.1cm
Width - 32.5cm
Height - 180cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Version 2 Date: 08/09/11

Glue safety - Take care when using glue, please follow the advice below
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals away
from the work area, small parts
could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand on the product,
this could cause damage.
• Assemble the item as close to
its nal position (in the same
room) as possible.
• Assemble on a soft level surface
to avoid damaging the unit or your
oor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Note: Only apply the glue once
you are sure of the assembly.
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
• Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority waste
disposal centre.
1
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Left side panel (178.4 x 29.9cm)
1
Right side panel (178.4 x 29.9cm)
2
Top panel
(32.4 x 30cm)
3Shelf x 2
(29.3 x 28.4cm)
6
Bottom panel
(29.3 x 29.8cm)
4
Front panel
(29.3 x 8.8cm)
9
Door x 3
(33 x 28.5cm)
8
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Pilot holes
for guidance
only
Top shelf
(29.3 x 28.4cm)
7
5Middle panel
(29.3 x 29.8cm)
Top back panel (101.5 x 30cm)
10
Bottom back panel
(66.4 x 30cm)
11
2
Pilot holes for guidance only
Pilot holes for guidance only
Pilot holes for
guidance only
Pilot holes
for guidance
only

Wooden dowel x 20 50mm Screw x 14
Door hinge x 6
30mm Screw x 6
12mm Screw x 3 14mm Screw x 9
Handle x 3Door stopper x 3
15mm Screw x 6
Glue x 1
Hinge plug x 3 Screw cover x 14
Wall plug x 1
AB
Components - Fittings
Tools required
Ruler - Use this ruler to help correctly identify the screws
I
C
DE
H
G
F
L
JK
MN
Note:
may be supplied than are required.
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
(This screw is
included in the
wall strap bag)
x 1
Wall strap x 1
3
O
Plastic support x 4
Metal plate x 3
P
110 120 130 140 1500 10 20 30 40 50 60 70 80 90 100
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Bradawl
(or sharp point)
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)

Assembly Instructions
Step 1
Fitting hinges and
handles to doors
4
8
8
D
P
I
I
C
H
a:
Metal plate onto the
Door .
Insert the Door hinges
into the Door .
D
I
P
8
8
b:
Handle onto the Door
C
H
8
.
Use the same method as
in a+b to assembly
another doors.
a:
b:
C

Assembly Instructions
Step 2
Fitting dowels and
door stopper
5
b:
Door stopper onto the
Shelf .
F
G
6
6
Place a small amount of
Glue into the dowel
holes. Insert Wooden
dowels into the Shelf
.
L
A
a:
b:
c:
s
J
6
F
G
A
A
A
A
A
A
A
A
A
A
A
A
J
5
c: Insert Hinge plug
into the Top shelf .
Place a small amount of
Glue into the dowel
holes. Insert Wooden
dowels into the Top
shelf .
J
7
L
A
7
7
J
a: Insert Hinge plug
into the Middle panel .
Place a small amount of
Glue into the dowel
holes. Insert Wooden
dowels into the Middle
panel .
J
5
L
A
5
A
L
J
A
L
F
G
A
L
X 2
Caution: Always
check the
assembly method
is correct before
applying glue.

Assembly Instructions
Step 3
Fitting the bottom
panel
6
a: Place a small amount
of Glue into the dowel
holes. Insert Wooden
dowels into the Bottom
panel .
L
A
4
a:
b:
c:
4
A
A
A
A
J
Insert Hinge plug into
the Bottom panel .
J
4
Plastic supports onto the
Front panel .
9
E
O
Front panel onto the
Bottom panel .
9
E
4
b:
E
c:
9
9
4
E
E
OO
O
O
E
E
E
E
Finished
front edge
Finished
front edge
J
A
L
Groove underneath
O
E

Assembly Instructions
Step 4
7
a:
b:
c:
Fitting left side panel
B
a: Place a small amount
of Glue into the dowel
panel and Middle
panel onto Left side
panel using Screws
.
4
5
1
L
1
4
5
BK
BK
E
Plastic supports onto the
Left side panel .
E
1
Use Screw covers to
cover the Screw heads.
K
4
8
b: Place a small amount
of Glue into the dowel
holes.
L
8
6
5
Continued on next page.
1
1
6
c: Place a small amount
of Glue into the dowel
holes.
L
E
O
O
O
Position Door onto
the unit, locating the
hinges into plug on
Bottom panel and
Shelf and
corresponding hole.
8
4
6
6
Position Door onto
the unit, locating the
hinges into plug on
Middle panel and
Shelf and
corresponding hole.
8
5
A
L
A
L
A
L

Assembly Instructions
Step 4 - continued
8
d:
6
d: Place a small amount
of Glue into the dowel
holes.
Position Top shelf
and Shelves onto
Left side panel using
Screws .
L
B
6
6
7
11
10
1
7
Use Screw covers to
cover the Screw heads.
K
B
B
B
K
K
K
Step 5
Fitting the back
panels
Note:
It would be useful
to ask someone to help
you at this stage.
Place a small amount
of Glue into the groove.
Carefully slide the Top
and Bottom back panel
and onto the unit.
11
L
L
10
A
L
1

Assembly Instructions
Step 6
Fitting the top panel
9
Step 7
Position Top panel
onto the unit using
Screws .
B
B
Place a small amount
of Glue into the dowel
holes and groove. Use
side panel onto the
unit.
Fitting the right side
panel
L
Plactic Support onto the
Right side panel .
E
2
Use Screw covers to
cover the Screw heads.
K
8
2
3
Use Screw covers to
cover the screw heads.
K
L
b: Place a small amount
of Glue into the groove.
L
a:
F
G
3
2
a:
Door stopper onto the
Top panel .
F
G
3
s
b:
F
G
O
Position Door onto
the unit, locating the
hinge into the plug on
Top shelf & Top
panel and
corresponding holes.
7
3
K
K
K
K
K
B
O
E
B
B
B
B
O
E
L
A
L
8
3
7
K
K
K
K
B
B
B
B

Assembly Instructions
Step 8
10
Customer Helpline: 08456 400800If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
It is recommended that the
strap onto the top panel.
With help, move unit into
position.
remove unit.
Drill a hole and insert Wall
plug .
strap using Screw .
Fixing to wall
Warning:
The unit is heavy.
Lift with care.
Warning:
Before drilling,
check wall for
hidden pipes and
cables.
E
M
N
M
Note:
Before use allow the
Glue to dry for 24 hours
and make sure the unit is
secure.
Top panel
wall
E
N
M
MM M N
Note: Wall plugs supplied are
for solid wall only.
be used for your wall, seek
professional advice if in doubt

A Guide to - Wall Mounting & Fixings
Revision 2 - 7/10/09
Important note:
Types of walls
Care &
Maintenance
No.1 “General Purpose” wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
No.3 “Cavity Fixing” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
loads, general purpose wall plugs can
be used.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
For use with plasterboard partitions or
hollow wooden doors.
heavy loads such as shelving, wall
cabinets and coat racks.
For use with walls stuck with
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5:
drilled hole.
If plastic wall plugs
are supplied with your
product:
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
responsibility of the installer.