Argos Stirling 343/9049 User manual

MADE IN
BRITAIN
Dimensions
Width - 72cm
Depth - 49cm
Height - 189cm
Stirling - 1 Drawer 2 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 07/11/14
Important - Please read these instructions fully before starting assembly
ALR3105
343/9049
345/7162

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 48kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step ladder
Electric drill
(do not use
for fitting
screws)

Components - Panels
Please check you have all the panels listed below
2
80%
90%
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Left Side (D3016A)
(1810 x 457mm)
Right Side (D3017A)
(1810 x 457mm)
1
7
13
2
14
8
6
10
12
9
3
4
5
Hanging Rail (FHR649)
(649mm long)
11
Door (D3019A)
(1553 x 339mm) x 2
Top (D3014A)
(718 x 490mm)
Base (D3015B)
(718 x 490mm)
Horizontal (D3018A)
(659 x 456mm)
Drawer Front (D3000A)
(685 x 245mm)
Left Drawer
Side (W370-195LH)
(370 x 195mm)
Drawer Base (T637-367)
(637 x 367mm)
Right Drawer
Side (W370-195RH)
(370 x 195mm)
Back (X1836-685)
(1836 x 685mm)
Back Rail (D3020A)
(659 x 123mm)
Drawer Back (W626-195)
(626 x 195mm)

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D E F
G H I
N
L
Small locking
nut (F3) x 2
C
Nail (F51) x 33
40mm Screw (F910) x 16
R
J
9mm Screw (F74) x 2
K
9mm Screw (F73) x 4
38mm Screw (F81) x 4
Knock-in Peg (F171GY) x 4
Large locking
nut (F900) x 2
Metal dowel (F901) x 4
Wooden dowel (F22) x 2
M
Wedgefix (F639) x 4
PQ
Hinge (F518) x 6
Hinge plate
(F523) x 6
O
13mm Screw (F63) x 14
Rail holder
(F1014) x 2
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
QStrap
Screw Washer x 2
Overbalance protector kit (F269) x 1
Foot (F340) x 4
Handle (F463) x 4
S
Drawer runner (F1004) x 2

6
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
A
B
A
C
C
CC
89
Step 2
Prepare the drawer
front
Screw 2 metal dowels
into the drawer front .
Note: Tighten the metal
dowels up fully against
the panels.
A
6
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
8
9
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
8
9
6
C
C
9
8
A
A
6
8
9

Assembly Instructions
5
Step 4
6
F
F
Fit the drawer base
Slide the drawer base
down the grooves in the
large drawer sides
and and down into
the groove in the large
drawer front .
Step 5
Fit the large drawer
back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
7
8
9
6
10
8 9
7
10
10
F
7
F
F
Attach the handles
Attach 2 handles to
the drawer front using
screws .
O
H
Step 6
6
8
9
8 9
10
8
9
7
H
O
H
O
6
Step 7
Fit the wedgefixes
Turn the large drawer
assembly over and slide
4 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
M
M
M
M
M
M

Finished front edge
Finished front edge
Assembly Instructions
6
Step 8
P
Finished
front edge
I
S
Prepare the left side
a: Fit 3 hinge plates
to the left side
making sure that the slot
is facing towards the
finished front edge.
Push a rail holder into
the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Place a runner onto
the left side . Slide
back the top of runner
and use the 2nd hole
from the front to fit the
1st screw .
Screw a metal dowel
into the left side .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
P
1
N
1
S
1
I
S
I
1
a:
b:
L
A
1
N
L
P
P
P
A
I
S
I
1
1

Assembly Instructions
7
Step 9
Finished
front edge
Finished
front edge
G
G
Finished
front edge
I
S
Prepare the right side
a: Fit 3 hinge plates
to the right side
making sure that the slot
is facing towards the
finished front edge.
Push a rail holder into
the right side . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Place a runner onto
the right side . Slide
back the top of runner
and use the 2nd hole
from the front to fit the
1st screw .
Screw a metal dowel
into the right side .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
P
2
N
2
S
2
I
S
I
2
2
b:
a:
L
A
N
L
P
P
P
A
I
S
P
Finished front edge
2
Finished front edge
2
I
2
Fit the horizontal to
the right side
Attach the horizontal
to the right side using
2 screws .
5
2
G
Step 10
plain
chipboard
surface
5

Finished
front edge
Assembly Instructions
8
Step 11
Step 12
Fit the back rail to the
right side
Push the back rail
onto the right side .
Use a screwdriver to
tighten the large locking
nut fitted to the back
rail .
Note: Turn the large
locking nut as far as it
will go - more than 1/2 a
turn.
12
12
2
B
B
B
A
Note: Support
the back rail
until the left side
has been fitted
in the next step.
12
2
Finished
front edge
D
Prepare the back rail
Insert 2 large locking
nuts into the back rail
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap 2 wooden dowels
into the back rail .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
12
B
D
12
10mm
D
B
B
B
D
Plain chipboard
surface
12

G
G
G
G
Polystyrene
block
Polystyrene
block
Assembly Instructions
9
Step 13
Step 14
Fit the left side
Push the left side
onto the horozontal
and back rail .
Attach the left side to
the horizontal using 2
screws .
Use a screwdriver to
tighten the large locking
nut fitted to the back
rail .
1
5
12
B
12
G
G
1
5
G1
5
12
Fit the top
Attach the top to the
left side and right
side using 4 screws
. .
Note: To make it easier
to fit the top and base
panels, place polysty-
rene blocks from the
packaging underneath
the side panels to raise
the assembly.
3
1
2
G
3
1
2