Argos 338/7005 User manual

Assembly Instructions - Please keep for future reference 338/7005
Dimensions
Width - 194.5cm
Depth - 95cm
Height -150cm
Important
Version 1 Date: 03/12/14
Ohio Highsleeper Frame
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
- Please read these instructions fully before starting assembly
345/9270

1
WARNING
IMPORTANT! KEEP FOR FUTURE REFERENCE
Be aware of the risk of injury of young children falling from the upper bunk bed.
This bed complies the European Standard BS EN 747-1 and BS EN 747-2:2012.
Follow the information on the warnings appearing on the upper bunk bed and do not remove the
warning label.
Warning: “Children can become trapped between the bed and the wall. To avoid risk of serious
injury the distance between the top safety barrier and the wall shall not exceed 75mm or shall be
more than 230mm”.
Be aware of children can strangle in item such as ropes, strings, cords, harnesses and belt
attached to or hung on the bunk bed / high bed.
The top of the mattress shall be at least 160mm below the upper edge of guardrails.
Recommended use only mattress which is L190 x W90 cm, 17cm or less in thickness on upper
bunk bed.
Always use the recommended size mattress to prevent the likelihood of entrapment or falls.
The use of water or sleep flotation mattress is prohibited.
Prohibit more than one person on the upper bunk bed and do not allow horseplay on or under the
bed and prohibit jumping on the bed.
Warning: Do not allow children under 6 years old to use the top bunk bed due to the risk of injury
from falls.
Always use the ladder for entering and leaving the upper bunk bed.
Do not use substitute parts, and stop to use the bunk bed if any structural part is broken or missing.
Use of a night light may provide added safety precaution for a child using the upper bunk bed.
Periodically check and ensure that the guardrail, ladder, components and all assembly fastenings
are in their proper position and that care should be taken that no fittings are loose.
The maximum child weight : 75 Kgs.

2
Important – Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
components and tools listed on
the following pages.
ttings from the
plastic bags and separate them
into their groups.
away from the work area, small
parts could choke if swallowed.
space to layout the parts before
starting.
or put weight on the product,
this could cause damage.
Assemble the item as close
to its nal position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your oor.
To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
components are missing or
damaged.
easier with 3~4 people.
should be kept away from the
product due to possible risk of
injury.
.
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
and mild detergent, do no use
bleach or abrasive cleaners.
there are no loose screws on
this unit.
This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Handy Hints
children in the age 6 or above. be carried out by a competent
adult.

that all bolts and fittings are
tightend properly.

Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: Argos = 0345 6400800
Centre right side panel
(115 x 50cm)
1Left support panel
(66.5 x 50cm)
18
Right bottom panel
(67.8 x 48.3cm)
19
Left bottom panel
(50 x 25cm)
20
Left shelf
(50 x 25cm)
21
Centre Bottom panel
(37 x 7cm)
7
Bed frame (191.4 x 33cm) 11
Front bed frame (191.4 x 33cm) 12
Bed panel (191.4 x 95.2cm) 13
Left side panel (150 x 95.2cm) 15
Right back panel (115 x 69.4cm) 16
Centre left side panel
(115 x 50cm)
2
Centre back panel
(115 x 37cm)
3
Door panel x 2 (107.7 x 33.4cm) 4
Centre Shelf x 2 (37 x 33.4cm) 6
3
Left front support (25 x 7cm) 10
Centre front support (37 x 7cm) 8
Right front support (67.8 x 7cm) 9
Left back panel (85.1 x 69.4cm) 17
Drawer right side
panel x 3 (29.8 x 11.5cm)
22
Drawer left side
panel x 3 (29.8 x 11.5cm)
23
Drawer back panel x 3
(33.8 x 11.5cm)
24
Drawer front panel x 3
(36.4 x 16cm)
25
Drawer bottom panel
x 3 (34.7 x 29.4cm)
26
Table top (83.5 x 50cm) 5
Right side panel (150 x 95.2cm) 14
Pilot holes for
guidance only
Pilot holes for
guidance only
Pilot holes for guidance only

4
Please check you have all the ttings listed below
Ruler - Use this ruler to help correctly identify the screws
Tools required
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Components - Fittings
0 10 20 30 40 5 0 60 70 80 90 100 110 120 130 140 150
0123456
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or glue)
7mm Suitable drill bit
(for use with wall plug)
The screws length is measured from the head to the point (30mm screw shown).
42mm Bolt x 10
H
B
DE
G
F
J
I
K L
N O
A C
M
Q RP
TU
S
V
Sprint washer x 10
X
Allen key x 1
50mm Screw x 84 30mm Screw x 17 14mm Screw x 14
12mm Screw x 6 20mm Screw x 2 15mm Screw x 28
(24 pcs screws are
included in the door hinges
bag, 4 pcs for rail support)
(This screw is included in
the runners bag)
12mm Screw x 18 39mm Locking pin x 14
15mm Locking nut x 212mm Locking nut x 12 30mm Dowel x 1
Door hinge x 4 Runner x 6 Rail Support x 2
Plastic support x 7 Door Stop x 1 Handle x 5
Clothes rail x 1
Ladder step x 5Ladder post x 2
W
Door pad x 4
Y
Screw Cover x 40
(This bolt is included
in the ladder bag)


Step 1
Fitting the track a:
b:
b: Slide top of Runners
forward and fix as
shown using Screws .
N
Note: The front part of
the runner should be
approximately 1.7cm from
the front edge of the panel.
G
It would be useful to ask
someone to help you at
this stage.
5
Important:
Because of the
size of this unit we
recommend that it
is built in the room
intended for use.
Warnung:
Be aware of the
danger of young
children under six
years old falling
from the upper
bunk. Top bunk
beds are not
recommended for
children under six
years old.
Complies BS EN
747-1 and BS EN
747-2:2012.
Note: There are many
different kinds of screws
and parts. Ensure you
check before assembly.
Silde top of the Runners
back.
Use screws to fix the
Runners on the Centre
right side panel .
a: Position Runners in
front edge of the Centre
right side panel .
Continued on next page.
N
1
1
N
G
N
N
N
N
G
G
G
1
Pilot holes for
runner position
Finished front edge
N
N
N
G
G
G
G
G
G
1
G
N
Middle hole
1
1.7cm
B
A
G

Middle hole 1


Step 1 - continued
d:
c:
6
Note: The front part of
the runner should be
approximately 1.7cm from
the front edge of the panel.
Silde top of the Runners
back.
Use screws to fix the
Runners on the Centre
left side panel .
c: Position Runners in
front edge of the Centre
left side panel .
N
2
2
N
G
N
d: Slide top of Runners
forward and fix as
shown using Screws .
N
G
G
N
Middle hole 2
1.7cm
G
N
G
Middle hole
2
G
G
G
N
N
N
N
N
N
G
G
G
G
G
G
Pilot holes for
runner position
Finished
front edge
2
2


Step 2
Fitting the shelves
b:
a:
Rail support and Door
hinges ‘back plates’
onto the Centre right side
panel and Right
side panel .
Use Screws to fix the

O
M
F
1
14
a: Use Screws to fix
Plastic supports onto
the Center front support
.
P
C
8
c:
c: Use Screws to fix
Center front support
onto the Center bottom
panel .
8
7
C
Continued on next page.
7
F
M
P
C
C
P
F
F
M
F
M
F
M
C
P
C
P
C
P
C
P
O
F
O
M
F
1
14
8
7
8
F
O


Step 2 - continued
e: Position Centre left
side panel onto the
unit.
Fasten Screws(9 pcs)
by Allen key .
e:
d:
A
X
2
d: Fasten Screws(9 pcs)
by Allen key to fix
Centre right side panel
onto the Centre back panel
, Centre shelves
and Centre bottom panel
.
X
1
36
7
A
a:
a: Use Screws to fix
Plastic supports onto
the Right front support
.
P
C
9
Continued on next page.
Step 3
Fitting the right front
support
8
Use Screw covers(9 pcs)
to cover the screw
heads.
Y
P
C
A
A
A
A
A
A
C
PC
C
P
P
1
3
3
2
7
9
6
6
7
1
A
X
2
A
X
Y
Y
YY
Y
Y
Y
Y
A
A
A
A
A
A
A
A


Step 3 - continued
c: Use Screws by
Allen key to fix Right
bottom panel onto the
unit.
c:
b:
A
X
19
b: Use Screws to fix
Right front support
onto the Right bottom
panel .
9
19
C
9
C
P
C
P
C
P
C
P
A
A
19
19
1
9
1
A
X