Argos 617/2516 User manual

Basic Desk
Assembly Instructions - Please keep for future reference 617/2516
Dimensions
Depth - 50cm
Width - 70.5cm
Height - 72cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Version2 Date:14/04/11

Glue safety - Take care when using glue, please follow the advice below
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
• Check you have all the
components and tools listed on
pages 2 and 3.
rom the
plastic bags and separate them
into their groups.
• Keep children and animals away
from the work area, small parts
could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand on the product,
this could cause damage.
• Assemble the item as close to
room) as possible.
• Assemble on a soft level surface
to avoid damaging the unit or your
r.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Note: Only apply the glue once
you are sure of the assembly.
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
• Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority waste
disposal centre.
1

2
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Table top (70.4 x 50cm)
1
Front left leg (70.4 x 6cm)
2
Front right leg (70.4 x 6cm)
3
Left leg (70.4 x 6cm)
4
Right leg (70.4 x 6cm)
5
Bottom panel (60 x 16.5cm)
6
Pilot holes for guidance only
Pilot holes for guidance only
Right support (40 x 6cm)
10
Bottom right side panel (40 x 6cm)
12
Back support (57 x 6cm)
8
Front support (57 x 6cm)
9
Left support (40 x 6cm)
11
Bottom left side panel (40 x 6cm)
13
Pilot holes for guidance only
Pilot holes for guidance only
Pilot holes for guidance only
Pilot holes for guidance only
Pilot holes for guidance only
Pilot holes for guidance only
Pilot holes for guidance only
Pilot holes for guidance only
Pilot holes for guidance only
Pilot holes for guidance only
Back panel (60 x 6cm)
7

Plastic support x 12
3
Note: The quantities below are the correct amount to complete the assembly. in some cases mor
may be supplied than are required.
Components - Fittings
110 120 130 140 1500 10 20 30 40 50 60 70 80 90 100
0 1 2 3 4 5 6
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(medium & large)
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
Ruler - Use this ruler to help correctly identify the screws
ABC
DEF
G
Screw cover x 10
14mm Screw x 24
Bradawl
(or sharp point)
Wooden dowel x 4
50mm Screw x 12
Glue x 1
25mm Screw x 12

4
Assembly Instructions
Step 1
Step 2
Fixing plastic supports
A
B
Plastic supports onto the
Back and Front supports
and ,Right and Left
suports and ,
Bottom right side and left
side panels and .
8
A
B
C
Right and Left supports
and onto the Back
and Front supports
and .
A
A
A
A
A
AA
A
A
B
B
B
B
B
B
B
B
B
8
9
11 10
9
10
11
12 13
11
10
8
9
1110
8
9
C
C
C
C
D
D
B
B
B
A
A
A
Use Screw covers to
cover the Screw Heads.
D
Attaching support
panels
A
A
B
B
13 12
back edge
back edge

Step 3
Assembly Instructions
5
Attaching left and right
legs
Left leg onto the Left
support and Bottom left
side panel .
E
4
13
Step 4
Attaching bottom
panel
11
4
7
13
E
E
C
D
11
Back panel onto the
Left leg .
C
4
7
Use Screw covers to
cover the Screw heads.
D
a:
b:
a:
b:
Right leg onto the Right
support and Bottom
Right side panel .
E
5
12
10
Right leg onto the
Back panel .
C
5
7
Use Screw covers to
cover the Screw heads.
D
10
5
7
CD
E
E
Bottom panel onto the
Bottom right side and left
side panels and .
6
A
13
6
A
A
A
A
12 13
back edge
Finished
front edge
12
12
Finished
front edge
Finished
front edge
Finished
front surface

6
Assembly Instructions
Step 5
Attaching front legs
2
9
Step 6
F
G
Attaching table top
a: Place a small amount
of Glue into the dowel
holes.
Insert Wooden dowels
into the Front right and left
legs & , Left and
Right legs & .
G
F
12
13
5
3
13
12
Use Screw covers to
cover the Screw Heads.
D
F
F
F
4
32
5
4
A
Front and Back supports
& Right and left
supports onto
the Table top .
9
A
1
8
1
1
10 11
10
11
9
8
F
G
Front left leg and right leg
and onto the Front
support , Bottom right
side and left side panels
and .
EC
a:
b: Place a small amount
of Glue into the dowel
holes.
Carefully locate the
Table top onto the unit.
G
b:
2
F
3
Finished
front surface
3
9
2
C
D
C
D
E
E

Step 7
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
7
Finishing the unit
With help, place the unit in
the intended position.
It would be useful
to ask someone to help
you at the stage.
Assembly is complete.
Note: Before use allow the
Glue to dry for 24 hours and
make sure the unit is secure.
Note: