Argos Seattle 4Ft6 User manual

Seattle 4Ft6
Dimensions
Width - 166,9cm
Depth - 195,4cm
Height - 95,0cm
Assembly Instructions- Please keep for future reference
2376000
2177450
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
DR82532
Issue 1 - 04/07/14
Important – Please read these instructionsfully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
03456 400 800

2
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
Handy Hints
Safety and Care Advice
Important – Please read these instructionsfully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
•To reduce the
likelihood of
damaging your
product please
ensure that your
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
power drill is set on a low torque
setting.
• Remove all fittings from the
unit or your floor.
to its final position (in the same
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.

3
Head board
(136.5x 51.7cm)
1
FA2533
Drawer Base x 2
(86,8x 57,0cm)
14
P4110
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing parts, call the
Customer Helpline:
03456 400 800
leg head left side
(95,0x 15,2cm)
6
P6006
Left & Right plinth x 2
(191,0x15,0cm)
2
FA2530
Left & right rail X2
(191.0x 22,0cm)
3
P2040
Head pannel
(136,5x 43,0cm)
4
P2038
Foot board
(136,5x 43,2cm)
5
FA2536
Support rail X2
(189,7x 3,2cm)
10
MA2251
Drawerfront x 2
(94,6x 23,0 cm)
11
P4105
Drawer left & right side x 4
(57,0x 14,5cm)
12
P4107
Drawer Back x 2
(90,0x 14,5cm)
13
P4109
leg head end right
(95,0x 15,2cm)
7
P6007
leg foot right side
(43.4 x 15.2cm)
8
P6009
leg foot left side
(43.4 x 15.2cm)
9
P6008
mid plinth
(191,4x 6,0 cm)
15
P7047
mid rail
(191,4x 22cm)
16
P2042

4
Corner bracket x4
Please check you have all the fittings listed below
Tools required
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Components - Fittings
Phillips screwdriver
(medium & large)
Flatblade screwdriver
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer or drill)
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Scissors
(medium)
Setsquare
1/1
Locking screw x 32 (5x24mm)
B
FK1011
C
FK1411
A
E
Wheel x 10
F
FK1244
D
Carcase screw x 52 (4x40mm)
H
FK1006
Large locking nut x 68 (15x12mm) Wood dowel x 40 (8x30mm)
I
FK1012
15mm
G
K
Connecting plate x 3
J
FK1236
Glue x 1
Double locking screw x 18 (24/24mm)
FA1510
FK1052
Chipboardscrew x 8 (4x25mm)
M
FK1314
FA15040
FK1400
Backpannelscrew x 28 (4x15mm)
Chipboardscrew x 20 (3x15mm)
FK1311
Chipboardscrew x 18 (5x35mm)
FK1326
L
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
The screws length is measured from the head tothe point (30mm screw shown).
Wood dowel x 4 (5x30mm)
N
FK1410

5
5
C
C
C
C
C
C
Assembly Instructions
Step 1
Foot end assembly
a: Insert 6x wood dowel
Cwith a smal amount of
glue Hinto the holes of
foot board 5.
b: Insert 3x large locking
nut Aand 3x double
lockinginto screw Kinto
leg foot right side 8.
Use a screwdriver to
turn 3x large locking nut
Aclockwise to lock.
C: Insert 3x large locking
nut Aand 3x double
lockinginto screw Kinto
leg foot left side 9.
Use a screwdriver to
turn 3x large locking nut
Kclockwise to lock.
Continued on next page.
a:
b:
c:
8
A
A
A
A
A
K
K
K
K
K
K
A
A
9

5
8
9
B
B
BB
6
5
8
9
Assembly Instructions
Step 1 - continued
e: Screw 8x locking screw
Binto the holes on leg
foot side right 8, foot
board 5and leg
foot side left 9
e:
B
B
B
B
A
A
A
A
A
A
d:
Foot end assembly
d: Attach leg foot right
side 8and leg foot left
side 9on foot board 5
using 6x Large locking nut
A.
Use a screwdriver to
turn 6x large locking nut
Aclockwise to lock.
C
C
C
C
a:
2x
2
Step 2
Side assembly
next few steps must be
done 2 times!
(one assembly is left side
other is right side.)
a: Insert 4x wood dowel
Cwith a smal amount of
glue Hinto the holes of
left & right plinth 2.
Continued on next page.

7
CC
CC
Assembly Instructions
Step x
Xxxxxx
x: x
x: xx
x: xxx
Side assembly
b: Insert 4x wood dowel
Cwith a smal amount of
glue Hinto the holes of
left & right rail 3.
Assembly Instructions
c: Attach support rail
0with 9x chipboard
srews Ito left & right rail
3.
b:
c:
2x
Step 2 - continued
10
3
I
I
I
I
I
I
I
I
I
d: Attach left & right plinth
2with 5x carcase srew
Eto left & right rail 3.
Note: This step requires
2 people.
d:
2
E
E
E
E
E
3
3
2x
2x

A
A
15
N
N
N
N
AA
C
C
8
Assembly Instructions
Step x
Xxxxxx
x: x
x: xx
x: xxx
Assembly Instructions
Step 3
Mid pannels assembly
a: Insert 2x wood dowel
Cwith a smal amount of
glue Hinto the holes of
mid rail ^.
Insert 4x large locking nut
Ainto the holes of
mid rail ^.
b: Insert 4x wood dowel
Nwith a smal amount of
glue Hinto the holes of
mid plinth %.
a:
b:
16

9
Assembly Instructions
Step 4
Head end assembly
a: Insert 8x wood dowel
Cwith a smal amount of
glue Hinto the holes of
head board 1and head
pannel 4.
Note: We recommend to
build this part on the
packiging cartons to
prevent damage to your
product.
b: Insert 12x large locking
nut Aand12x double
lockinginto screw Khead
board 1and head pannel
4.
Use a screwdriver to
turn 12x large locking nut
Kclockwise to lock.
Continued on next page.
a:
b:
1
4
C
C
C
C
C
C
C
C
K
K
K
K
K
K
K
K
K
K
K
K
4
1
A
A
A
A
A
A
A
A
A
A
A
A

10
B
B
Head end assembly
Turn the head end on
the other side.
2 people required!
d: Screw 8 locking screws
Binto the holes on leg
head right side 6, head
pannel 4and
leg head left side 7.
Assembly Instructions
Step 4 - continued
Head end assembly
c: Apply a smal amount of
glue Honto wood
dowel Calready fixed into
head board 1and head
pannel 4.
Attach leg head right
side 6and leg head left
side 7to head panel 4
and head board 1with
12x large locking nut A.
Use a screwdriver to
turn 12x large locking nut
Aclockwise to lock.
c:
4
1
6
7
4
7
6
1
B
BB
d:
BBB
A
A
A
A
A
A
A
A
A
A
A
A