Argos Cheval 146/7965 User manual

MADE IN
BRITAIN
Dimensions
Width - 69cm
Depth - 49.5cm
Height - 200cm
Cheval - 2 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 10/01/14
Important - Please read these instructions fully before starting assembly
ALR2962
146/7965
147/4068
152/7324
146/8548

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 44.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
1 2
80%
x 3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
4
3Top (D2721A)
(690 x 494mm)
5
Horizontal (D2722A)
(654 x 456mm) x 2
Door (D2725A)
(1888 x 337mm) x 2
Back (X1890-674)
(1890 x 674mm)
Plinth (D2723A)
(654 x 86mm)
6
89
Hanging Rail (FHR646)
(646mm long)
7
Right Side (D2719A)
(1981 x 458mm)
Left Side (D2720A)
(1981 x 458mm)
Rail (D2724A)
(654 x 86mm) x 2

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 18
B
Metal dowel (F901) x 14
C
D E
Large locking
nut (F900) x 14
F
G H I
L
Nail (F51) x 35
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
M
K
see malibu fitment mk2 for large number of panels and fittings
Rail Holder
(F891) x 2
19mm Screw (F461) x 4
13mm Screw (F63) x 1613mm Screw (F79) x 1
Bracket (F327) x 1
Handle (F274) x 2
Tools required
Rule
Scissors
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step
ladder
Electric drill
(only use
when drilling
into walls)
Square
mm 10 20 30 40 50 60 70 80 90 100 mm 10 20 30 40 50 60 70 80 90 100
40mm Screw (F910) x 4
Hinge (F518) x 6
Hinge plate
(F523) x 6
N
Plastic Nail (F91) x 4

Finished
front edge
A
A
A
A
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Step 2
Prepare the left side
Tap 2 wooden dowels
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Screw 7 metal dowels
into the left side .
Note: Tighten the metal
dowels up fully against
the panels.
Fit 3 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
Fit the rail holder to
the left side using 2
screws .
To fit the rail holder, screw
through its top hole and into the
shallow mark hole drilled in the
panel. Make sure that it is fitted
straight, in line with the panel
edges and then fit another
screw using the lower hole.
Prepare the right side
Tap 2 wooden dowels
into the right side .
Screw 7 metal dowels
into the right side .
Fit 3 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.
Fit the rail holder to
the right side using 2
screws .
A
10mm
A
K
B
B
1
1
1
K
A
B
2
2
2
K
K
K
K
B
B
B
B
B
B1
K
K
K
K
B
B
B
B
B
Finished
front edge
2
H
I
H
I
I
1
H
I
2
H
I
HH
I
HH
B
B
B

Finished
front edge
Finished
top edge
A
Finished
front edge
Finished
front edge
A
Assembly Instructions
5
Step 3
Step 4
Finished
front edge A
A
A
C
C
C
C
Prepare the 2
horizontals
Tap 4 wooden dowels
into each horizontal .
Insert 4 large locking
nuts into each
horizontal .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
A
4
4
C
Cx 2
4
4
4
Fit the 2 horizontals
to the right side
Push the 2 horizontals
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted
each horizontal .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Step 5
2
4
C
C
4
2
A
C
C
A
A
C
C
Prepare the plinth and
the 2 rails
Tap 2 wooden dowels
into the plinth and
each of the 2 rails .
Insert 2 large locking
nuts into the plinth
and each of the 2 rails
. .
Note: The plinth and the
2 rails can have a plain
chipboard surface.
A
5
6
6
5
C
5
6
B
C
Note: The rails have a finished top edge.
Plain
chipboard
surface
x 2
Plain
chipboard
surface

Finished
front edge
Assembly Instructions
6
Step 6
2
Finished
top edge
5
6
Fit the plinth and rails
Push the plinth onto
the right side .
Use a screwdriver to
tighten the large locking
nut fitted to the plinth
. .
Push the 2 rails onto
the right side .
Use a screwdriver to
tighten the large locking
nuts fitted to the 2
rails .
2
C
5
5
2
C
6
6
Note: Support the plinth
and the rails until the left
side has been fitted in
the next step.
5
6
Step 7
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 7 large
locking nuts fitted to
the horizontals , the
plinth and the 2 rails
. .
1
C
4
5
6
Note: The 2 rails have
a finished top edge.
1
4
4
Finished
top edge
6
6

E
E
E
E
Assembly Instructions
7
Step 8
Step 9
Fit the top and the
plastic nails
Push the top onto
the assembly and secure
it to the sides and
using 4 screws .
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. as shown.
3
1 2
E
2
b:
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit, making
sure it is pushed up
against the top .
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
Stand the unit up for
the next step.
9
3
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
y
y
x
D
Warning: The
unit is heavy.
Lift with care.
3
9
1
3
Finished
front edge
9
N
N
N
1
2
N
N
x

Assembly Instructions
8
Step 10
Step 11
7
I
Fit the hanging rail
Push the hanging rail
. into the rail holders
fitted to the side panels.
7I
L
HH
90
L
L
HH
L
HH
Prepare the 2 doors
Push fit 3 hinges into
each of the doors .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
H
L
8
8
x 2
7

Assembly Instructions
9
Step 12
Fit doors and handles
Note: The easiest way to
attach each door is
to fit the top hinge first,
then align and fit the
other hinges.
a: Push the hinge
onto the front part of the
hinge plate .
The recess at the bottom
of screw B goes into the
slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle to
each door using 2
screws .
L
L
L
K
K
K
L
K
M
F
8
8
e:
a: b:
c: d:
K
L
K
K
B
K
L
L
L
A
L
K
B
F
M
F
8
8
M