Argos Calgary 476/7978 User manual

MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
Calgary - Corner Desk
Assembly Instructions - Please keep for future reference 476/7978
462/6930
Width - 100cm
Depth - 82cm
Height - 74cm
Issue 1 - 25/11/15
Shelf section on the right
Shelf section on the left

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 24kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below When applicable, remove any
protective film before use
2
6
1
Desktop (DF4608)
(99.6 x 49cm)
Back Panel (DF4614)
(70.6 x 33.8cm)
Shelf Divider (DF4612)
(32.25 x 31.5cm) x 2
Shelf End (DF4613)
(69.1 x 32.3cm) x 2
Shelf Base (DF6423)
(61.5 x 31.9cm)
Shelf Panel (DF4611)
(61.5 x 31.9cm)
Shelf Top (DF4610)
(64.9 x 32.7cm)
End Panel (DF4609)
(70.6 x 35.4cm)
2 3
4
5
7 8

Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Tools required
3
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D E F
G H I
C
J
Large locking
nut (F900) x 26
Metal dowel (F901) x 22
Wooden dowel (F22) x 8
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Foot (F854) x 1
Double metal dowel (F566) x 2
Plastic Nail (F91) x 7 25mm Screw (F50) x 1
25mm Screw (F484) x 4 Plastic Insert (F502) x 4 Allen Key (F36) x 1

D
D
Assembly Instructions
4
Prepare the shelf
panel
Insert 4 large locking
nuts into the shelf
panel .
Note: The arrows on the
locking nuts must point
towards the holes in the
edge of the panels.
Tap 4 wooden dowels
into the shelf panel .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Step 1
Step 2
B
3
D
3
x 2
B
B
B
B
B
D
10mm
D
D
B
B
B
B
Prepare the 2 shelf
dividers
Insert 4 large locking
nuts into each of the
2 shelf dividers .
B
5
5
3
DO NOT USE the shelf base.
It is similar to the shelf panel
but, it has a shallow mark hole.

Fit the other divider
Push the divider onto
the shelf panel .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the divider .
Assembly Instructions
5
Step 3
Step 4
C
B
C
C
Fit a divider to the
shelf panel
a: Tap 2 double metal
dowels through the
holes in the middle of the
shelf panel and push
a divider onto them
until they ‘’bottom out’’.
b: Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the divider .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
3
5
C
B
B
3
5
a:
b:
5
B
5
5
3
5
3
3
5

Assembly Instructions
6
Step 5
Prepare the shelf
base
a: Insert 4 large locking
nuts into the shelf
base .
Tap 4 wooden dowels
into the shelf base .
Turn the shelf base
over
b: Screw 2 metal
dowels into the shelf
base .
Note: Tighten the metal
dowels up fully against
the panels.
B
2
D
2
D
D
B
B
B
B
D
D
2
A
A
A
Turn the
shelf base
over
A
2
Fit the shelf base
Push the shelf base
onto the divider .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the divider .
Step 6
B
2
5
5
2
5

Assembly Instructions
7
Step 7
Prepare the 2 shelf
ends
Screw 4 metal dowels
into each of the 2 shelf
ends .
Insert 2 large locking
nuts into each of the
2 shelf ends .
A
A
A
A
x 2
B
B
A
4
B
4
4
Fit a shelf end
Push a shelf end onto
the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the shelf base and
the shelf panel .
Step 8
B
4
2
3
Fit the other shelf end
Push a shelf end onto
the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the shelf base and
the shelf panel .
Step 9
B
4
2
3
2
3
4
2
3
4

Assembly Instructions
8
Step 10
Prepare the shelf top
Screw 6 metal dowels
into the shelf top .
Step 11
A
A
A
A
A
A
A
1
1
Fit the shelf top
Push the shelf top
onto the assembly.
Use a screwdriver to
tighten the 6 large
locking nuts fitted to
the 2 shelf ends and
the divider .
Step 12
B
1
4
5
1
4
4
5
J
F
Fit the foot and
plastic nails
Screw the foot onto
the shelf base using
screw .
Tap 2 plastic nails
into the bottom edge of
each of the shelf ends .
Carefully stand the
assembly up for the
next step.
J
2
4
F
E
2
Warning: The
unit is heavy.
Lift with care.
E
EE
E
4
4

Assembly Instructions
9
Step 13
Prepare the back
panel
Insert 4 large locking
nuts into the back
panel .
Step 14
A
A
B
B
Prepare the end panel
Screw 2 metal dowels
into the end panel .
Insert 2 large locking
nuts into the end
panel .
A
B
7
7
B
8
7
B
B
B
B
Step 15
Fit the back panel to
the end panel
Push the back panel
onto the end panel .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the back panel .
B
8
7
8
8
8
7