Argos New Hallingford 274/4917 User manual

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
MADE IN
BRITAIN
Dimensions
Width - 37.5cm
Depth - 40cm
Height - 58cm
More help is available throughout this booklet by scanning
in the QR codes or typing in the links
Assembly Instructions - Please keep for future reference
Issue 8 - 26/10/16
New Hallingford - 3 Drawer Bedside
274/4917
266/4509
258/7693
266/2910
266/7379
616/9749
618/4999
601/6737
620/9379
618/6959

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 14kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it must be
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.

Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below
When applicable, remove any protective film
from the panels before they are used
2
1Left Side (D2307A)
(55.6 x 37.2cm)
2Right Side (D2308A)
(55.6 x 37.2cm)
3
4 5
86 7
9 10
Top (D2306A)
(37.5 x 39.6cm)
Back (X535-366)
(53.5 x 36.6cm)
Rail (D2310A)
(34 x 6.6cm) x 2
Drawer Front (D2309A)
(36.2 x 16.2cm) x 3
Drawer Base (T304-367)
(30.4 x 36.7cm) x 3
Drawer Back (W291-124)
(29.1 x 12.4cm) x 3
Left Drawer Side (W370-124LH)
(37 x 12.4cm) x 3
Right Drawer Side (W370-124RH)
(37 x 12.4cm) x 3

Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
3
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
B C
D E F
G H
Small locking cam
nut (F3) x 6
Nail (F51) x 12
13mm Screw (F63) x 18
I
A
Wooden dowel (F22) x 6
19mm Screw (F461) x 6
Metal dowel (F901) x 12
Large locking cam
nut (F900) x 6 Knock-in Peg (F171GY) x 12
J
Handle (F278) x 3
M
Plastic Nail (F91) x 4
L
Wedgefix (F639) x 6
Kb
Ka
350mm long
CL
CR
CR Runner (F424) x 3
CL Runner (F422) x 3
Kc
KdDR
DL
DL Runner (F425) x 3
DR Runner (F426) x 3
9mm Screw (F73) x 18

4
Step 1
Assembly Instructions
5
x 3
B
B
B
C
B
B
Groove
C
5
x 3 x 3
x 3
Step 2
Prepare the 3 drawer
fronts
Screw 2 metal dowels
into the holes shown on
the back of each drawer
front .
Note: Tighten metal
dowels up fully against
the panels.
B
5
Prepare the drawer
sides
Insert a small locking
cam nut into the hole
shown on the left drawer
side and right drawer
side .
Note: The arrow on the
locking cam nut must
point towards the hole in
the edge of the panel.
Step 3
C
6
7
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
cam nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
cam nuts clockwise
to secure panels - more
than 1/2 a turn.
6
7
5
C
6
7
C
CC
67
6
7
www.youtube.com/watch?v=3fYL5zB6ZYQ
Drawer Assembly

Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
9
6 7
5
8
6 7
9
8
8
E
6 7
Attach the handle
Attach a handle to
each drawer front
using 2 screws .
Step 7
J
G
5
E
E
E
J
5
G
G
x 3
x 3
x 3
L
L
L
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
L
7
9
6
8
E
Important: Make sure
that the drawer assembly
is square before fitting
the wedgefixes.
5
x 3
7
6
9

Assembly Instructions
6
Step 8
Fit runners to the
drawers
Turn the 3 drawer
assemblies over.
Fit runner , marked
with ‘DR’, to the bottom
edge of the right drawer
side , as shown,
making sure that it is
pushed up against the
back of the drawer front
. .
Use a bradawl to mark
the fixing positions, then
secure with 2 screws .
Fit runner , marked
‘DL’, to the bottom edge
of the left drawer side
using the same method.
6
K d
7
5
I
K c
K c
D
D
D
A
10mm
A
Prepare the 2 rails
Tap 2 wooden dowels
into each rail .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking cam
nuts into each rail .
Note: The arrow on the
locking cam nut must
point towards the hole in
the edge of the panel.
A
A
Step 9
x 2 4
4
D4
Plain
chipboard
surface
5
6
7
x 3
Runners must be
pushed up against
the drawer front
DL
I
I
DL
I
I
K d
DR
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounter Runners

Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 10
a:
Prepare the left side
a: Fit 3 CL runners
to the left side .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the hole at the top of the
runners .
Screw 2 metal dowels
into the left side .
Insert a large locking
cam nut into the left
side . .
Tap a wooden dowel
into the left side .
b:
B
D
1
1
K a
1
H
H
I
K a
B
D
A
A
1
1
1
K a
H
1st
screw
Finished
front edge
CL
Finished
front edge
CL
I
CL
I
CL
I
I
CL
H
H
K a
H
CL
H
H
K a
H
CL
H
H
K a
H
K a
B
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounter Runners

CR
CR
CR
A
Assembly Instructions
8
Step 11
Prepare the right side
a: Fit 3 CR runners
to the right side .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the hole at the top of the
runner .
Screw 2 metal dowels
into the right side .
Insert a large locking
cam nut into the right
side .
Tap a wooden dowel
into the right side .
B
D
2
2
K b
2
H
H
I
K b
a:
b:
D
B
Finished
front edge
Finished
front edge
A
2
2
2
Join the right side and
rails
Push the 2 rails onto
the right side .
Use a screwdriver to
tighten the 2 large
locking cam nuts
fitted to the rails .
Note: Turn the large
locking cam nuts as
far as they will go - more
than 1/2 a turn.
B
D
D
2
4
2
4
D
Step 12
Note: Support this
rail until the left
side has been fitted
in the next step.
4
4
K b
H
1st
screw
Finished
front edge
CR
Finished
front edge
I
CR
I
CR
I
CR
I
CR
H
H
H
K b
CR
H
H
H
K b
CR
H
H
H
K b
K b
B

CR
CR
CR
CR
CR
CR
Assembly Instructions
9
Step 13
Fit the left side
Push the left side
onto the 2 rails .
Use a screwdriver to
tighten the 2 large
locking cam nuts
fitted to the rails .
D
4
1
1
4
4
B
B
Step 14
Prepare the top
Screw 2 metal dowels
into the top .
Step 15
B
3
Shaped
front edge
3
3
Fit the top
Push the top onto
the 2 sides and .
Use a screwdriver to
tighten the 2 large
locking cam nuts
fitted to the sides
and .
D
3
1 2
1
2
1
2
4
Plain
chipboard
surface