Argos Denver 355/8463 User manual

MADE IN
BRITAIN
Dimensions
Width - 75cm
Depth - 40cm
Height - 93cm
Denver - 4 Drawer Chest
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 20/10/14
Important - Please read these instructions fully before starting assembly
ALR3094
355/8463
332/4790
333/7062

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 29kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance kit supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
12
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
3
5 6 7
8
9 10
Top (D1567A)
(718 x 395mm)
Left Side (DF2098A)
(930 x 396mm)
4
Drawer Base (T697-367)
(697 x 367mm) x 4
Left Drawer
Side (W370-124LH)
(370 x 124mm) x 4
Drawer Front (DF2092A)
(742 x 192mm) x 4
Rail (D1570A)
(718 x 60mm) x 4
Right Drawer
Side (W370-124RH)
(370 x 124mm) x 4
Right Side (DF2099A)
(930 x 396mm)
Drawer Back (W686-124)
(686 x 124mm) x 4
Back (X848-744)
(848 x 744mm)

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 20
C
D E F
G
J
H
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Small locking
nut (F3) x 8
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
9mm Screw (F74) x 8 9mm Screw (F73) x 16
Drawer runner (F1004) x 8
Large locking
nut (F900) x 12
Nail (F51) x 20
K
Electric drill
(do not use for
fitting screws)
I
Wedgefix (F639) x 16
Plastic Nail (F91) x 4
LStrap Screw Washer x 2
Overbalance protector kit (F269) x 1
Knock-in Peg (F171GY) x 16

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 4
x 4
x 4
x 4
5
B
B
B
C
C
CC
67
Step 2
Prepare the 4 drawer
fronts
Screw 2 metal dowels
into each of the drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
B
5
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
6
7
Attach the drawer
sides to the drawer
front
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
6
7
5
C
C
6
7
6
7
B
B
5

Assembly Instructions
5
Step 4
H
H
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
9
6 7
5
8
6 7
9
8
8
H
6 7
Step 6
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 4 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
K
H
H
K
K
K
K
K
9
6
8
6
7
9
7
5
x 4
x 4
x 4

Finished
front edge
Assembly Instructions
6
Step 7
Finished
front edge
F
J
Prepare the left side
a: Place 4 runners on
the left side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
Screw 6 metal dowels
into the left side .
1
F
F
1
J
J
B
1
a:
b:
F
J
F
F
F
F
B
Finished
front edge
F
J
F
J
F
J
B
B
B
B
B
1
1
Finished
front edge
F
J
Step 8
Prepare the right side
a: Place 4 runners on
the right side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
Screw 6 metal dowels
into the right side .
2
F
F
2
J
J
B
2
F
J
F
J
B
F
J
F
J
F
F
F
F
B
B
B
B
B
Finished
front edge
Finished
front edge
2
2

A
Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 9
Step 11
Prepare the top
Insert 4 large locking
nuts into the top .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
D
D3
D
D
D
D
Finished
front edge
Step 10
Fit the top to the right
side
Push the top onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the top .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
3
3
2
D
D
B
D
3
3
2
D
D
x 4
Prepare the 4 rails
Insert 2 large locking
nuts into each of the
4 rails .
Tap 2 wooden dowels
into each of the 4 rails .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
D
44
A
10mm
A
A
4

Assembly Instructions
8
Step 12
Step 13
2
4
4
4
2
Fit 3 of the rails
Push 3 rails onto the
right side .
Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the 3 rails .
4
2
D
4
Fit the last rail
Push the last rail
onto the right side .
Use a screwdriver to
tighten the large locking
nut fitted to the last
rail .
4
2
D
4
Note: Support this rail
until the left side has been
fitted in the next step.
4
Step 14
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 6 large
locking nuts fitted to
the top and rails .
1
D
3 4 4
4
4
4
3
1

yy
Assembly Instructions
9
Step 15
Step 16
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
evenly spaced out.
10
G
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
10
xx
yy
xx
b:
G
10
Fit the 4 plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
Stand the unit up for
the next step.
I
1
2
I
II
I
2
1