Argos Hallingford 305/2811 User manual

Hallingford - 2 Door Sliding Robe
Dimensions
Width - 100,5cm
Depth - 60,3cm
Height -205,7cm
Issue1 - 12/05/2013
Important – Please read these instructionsfully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800
Assembly Instructions - Please keep for future reference
305/2859
305/2842
305/2828
305/2835
305/2811
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
DR89954

2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 2 and 3.
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
•This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below

Components - Panels
Please check you have all the panels listed below
3
Right side
(205.6 x 58cm)
2
P2350
Left side
(205.6 x 58cm)
1
P2350
3Slide door
(196.3 x 50cm)
4
P3530
Top
(96.7 x 55.7cm)
6
P1564
Bottom
(96.7 x 55.7cm)
7
P1565
Large horizontal
(96.7 x 46.7cm)
8
P1563
5
Plinth front
(96.6 x 14cm)
12
P7334C
Plinth back
(96.6 x 5.4cm)
P7335C
Pelmet
(100.5 x 6.5cm)
FA250
Foldy back
(199.3 x 98cm)
10
BO33933
9
Mirror slide door
(196.3 x 50cm)
11
PS3529
Plinth top
(96.7 x 7cm)
P7293

4
Please check you hav tings listed below
Chipboardscrew x10(4x40mm)
Ruler - Use this ruler to help correctly identify the screws
Tools required
A
Screw x 21 (3.9x32mm)
E
Expando housing x 3 (20x12mm)
B
Twister leg x 14 (5x24mm)
H
Expanding dowel x 3 (5x8.5mm)
C
I
Q
Note: The quantities below are the correct amount to complete the assembly. In some cases more
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Pozi screw x 2 (4x12.5mm)
F
L-Bracket x 1
Backpanelscrew x 5 (4x15mm)
D
Sliding door guide x 4
K
Twister cam x 14
(15x12mm)
MP
Sliding door roller adjustable x 2
U
Sliding door roller x 2
L
G
J
Felt x 6
R
Doorstop x 5
S
Hanger rail x 1
(1126mm)
T
Components - Fittings If you have damaged or missing components,
call the Customer Helpline: 0845 6400800
Phillips screwdriver
(medium & large)
Flatblade screwdriver
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or drill)
5mm Suitable drill bit
PR1964
PM1884
FK1416
FK1324
FK1012
FK1274
FK1011
FK1318
FK1056
FK1051
FK1400
FK1235
Hanger rail support x 2
FK1217
FK1309
Peg x 3
FK1234
FK1273 FK1272
FK1417
2.5mm Suitable drill bit
Stairs
Piercer Scissors
(medium)
(small) Level ruler
Setsquare
Sliding rail x 4
(966mm)
PK165*
FA1515
Nail x 60
Handle moulding x 3
(1904mm)
WX
Wall plug and parkerscrew x 1
ZF99936

5
a:
Step 2
Step 1
A
A
H
H
H
H
H
H
H
1/2
a: Attach hanger rail
support using 12.5mm
screw onto sides
Note: Two pannels
I
I
I
M
M
1
2
10
6
9
2
F
F
b:
Screw twister leg into
sides
Note: twister leg as far
as shown.
Do not over tighten.
12
1/2
H
H
M
F
Attaching plinths
b:
Align the sides of plinth
front with bottom as
shown and attach using
chipboardscrew .
Note: there are no
predrilled holes for 40mm
screw .
Repeat with plinth back

6
Assembly Instructions
Step 3
a: Insert expando housings
into top .
Flip panel
a:
B
B
B
B
W
5
5
6
6
5
5b:
b: Carefully knock sliding
rail into top by using
a hammer.
Reapeat b for bottom

Locate the 'mating'
panel over the Cam Leg.
Insert the Cam so the
longer 'slot' is pointing
towards the Cam Leg.
Use a Flat Bladed
Screwdriver to turn Cam
clockwise as far as it will go
The final 'locked' position will
be more than half a turn.
M
MI
I
7
Assembly Instructions
Step 4
Attaching panel
Repeat Step 4 for the
second side
Position top , bottom
and horizontal
Insert twister cam into
panels where shown.
Usa a screwdriver to turn
twister cam clockwise to
lock.
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
1
1
1
6
6
5
5
7
5/6/7
7
6
7
5
Step 5

8
Assembly Instructions
Step 6
P
P
9
Fitting back panel
Attach foldy back to
back of wardrobe with
the coloured surface facing
the inside of the unit using
nails
Nails should be spaced
about 150mm apart.
8
P
A:A = B:B
A
A
B
Important!
Cabinet MUST
be ‘square’
before back is
attached.
A
A
B
B
B

9
Assembly Instructions
Step 7
S
S
Align the unit
Stand up the unit
Use a spirit level to check if
the base of this unit
is level front-to-back ,
side-to-side and
top-to-bottom in the three
positions shown.
Use pegs to level your
unit in all three direction
shown. Knock peg in, as
far as you require, under the
ends of the unit and then
panel.
S
SNAP!
1
1
2
2
3
3

10
Assembly Instructions
Step 8
Insert hanger rail
Step 9
M
S
V
GLASS handle with care
T
T
T
T
4
4
Flush with
end of Door
Flush with
end of Door
Fitting handle to mirrordoor
Hold hande mouldings up
against front of mirror slide
door , make sure the ends
mirror slide door .
Screw screwsinto the ‘V’
groove of the handle
moulding .
Tip: start with the end screws,
then the centre screw and
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
Place hanger rail
onto hanger rail supports
.
U
M
T
T
E
E
E
E
E
E
E
E
E
E
E
E
E
E
4