Argos Eden 414/1594 User manual

MADE IN
BRITAIN
Dimensions
Width - 47.5cm
Depth - 38cm
Height - 51cm
Eden - Small Side Table
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 15/05/15
Important - Please read these instructions fully before starting assembly
ALR3154
414/1594
414/4962

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 10kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
12 3
100%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
4 5
Left End (DF3748)
(475 x 378mm)
Drawer Front (DF3752)
(393 x 194mm)
Right End (DF3749)
(475 x 378mm)
Top (DF3750)
(475 x 381mm)
Base (DF3751)
(399 x 372mm)
6Drawer Back (W366-165)
(366 x 165mm)
Drawer Base (T378-347)
(378 x 347mm)
Left Drawer Side (W350-165LH)
(350 x 165mm)
Right Drawer Side (W350-165RH)
(350 x 165mm)
7 8
9
10 Back (X452-417)
(452 x 417mm)

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D E F
G H I
C
Small locking
nut (F3) x 2
Nail (F51) x 12
L
J
9mm Screw (F74) x 2
K
9mm Screw (F73) x 4
Drawer runner (F1004) x 2
Knock-in Peg (F171GY) x 4
Metal dowel (F901) x 2
Wedgefix (F639) x 2
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Small metal dowel (F893) x 8
Hollow core
locking nut
(F892) x 8 19mm Screw (F461) x 2
Handle (F414) x 1

5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
A
B
A
B
B
BB
78
Step 2
Prepare the drawer
front
Screw 2 metal dowels
into the drawer front .
Note: Tighten the metal
dowels up fully against
the panels.
A
5
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
B
7
8
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
7
8
5
B
B
7
8
8
7
5
A
A

Fit the wedgefixes
Turn the drawer
assembly over and slide
2 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
5
Assembly Instructions
5
Step 4
C
C
13
8
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Step 6
9
78
5
9
Attach the handle
Attach the handle to
the drawer front
using screws .
F
5
L
7
8
7
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
6
7 8
9
6
6
C
7 8
C
C
9
6
Step 7
II
I
I
F
F
L
5

Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 8
Finished
front edge
E
E E
E
1 1 1
c:
a:
b:
E
Finished
front edge
H
K
H
K
Prepare the left end
a: Place a runner on
the left end as
shown. Slide back the
top of runner and use the
1st hole from the front to
fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left end .
c: Push 2 hollow core
locking nuts into the
left end , making sure
that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Note: The pin should be
tapped in flush with the
top surface of the hollow
core locking nut .
Screw 2 small metal
dowels into the left
end .
1
H
H
1
K
K
H
D
D
E
E
E
1
D
1
1
1
1

Assembly Instructions
7
Step 9
c:
a:
b:
Prepare the right end
a: Place a runner on
the right end as
shown. Slide back the
top of runner and use the
1st hole from the front to
fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right end .
c: Push 2 hollow core
locking nuts into the
right end , making
sure that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Note: The pin should be
tapped in flush with the
top surface of the hollow
core locking nut .
Screw 2 small metal
dowels into the right
end .
2
H
H
2
K
K
E
E
E
2
D
2
Finished
front edge
H
K
H
K
Finished
front edge
Finished
front edge
Finished
front edge
H
E
E
D
D
2
2
2

Finished front edge
Finished front edge
Assembly Instructions
8
Step 10
Prepare the base
Push 4 hollow core
locking nuts into the
base , making sure
that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
E
E
E
E
E
E
44
Finished
front edge
Fit the base to the
right end
Push the base onto
the right end .
The 2 small metal dowels
. fitted to the right end
. must slide into the
top of the 2 hollow core
locking nuts fitted to
the base . .
Insert a screwdriver into
the 2 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
D
E E
2
4
D
2
E
4
E
Step 11
Fit the left side
Push the left end
onto the base .
The 2 small metal dowels
. fitted to the left end
. must slide into the
top of the 2 hollow core
locking nuts fitted to
the base . .
Insert a screwdriver into
the 2 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
4
1
D
1
E
4
E
Step 12
2
4
41

yyyy
xx
xx
Assembly Instructions
Step 13
Prepare the top
Screw 4 small metal
dowels into the top . D
D
D
D
D3
3
Finished
front edge
Finished
front edge
Fit the top
Push the top onto the
assembly.
The 4 small metal dowels
. fitted to the top
must slide into the top of
the 4 hollow core locking
nuts fitted to the ends
. and .
Insert a screwdriver into
the 4 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
3
D3
E
1 2
E
Step 14
Step 15
3
1
2
b:
J
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
Stand the unit up for
the next step.
10
J
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
10
9
10