Argos Washington 425/8425 User manual

Dimensions
Assembly Instructions - Please keep for future reference
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
Height - 112.3cm
Depth - 45cm
Width - 80.3cm
Washington - 5drw
425/8425
414/1673
414/1673 WARM OAK
Issue 1 - 02/07/15
DR82535
425/8425 SMOKEY OAK
Important–Please read these instructions fully before starting assembly
Alternatively, call the Spares Helpline on: 0370 112 1928
For any other queries please contact the Customer Helpline on: 0345 640 2020
If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk
or email: [email protected] (quoting your original order number)

1
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
•
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fi ttings are
tightend properly.
Handy Hints
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below•
Important – Please read these instructions fully before starting assembly
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Check you have all the
components and tools listed
on the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• We do not
recommend the
use of power drill/
drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
Safety and Care Advice

For damaged or missing parts, please visit:
www.argos-support.co.uk or email: [email protected]
Please check you have all the panels listed below
Components - Panels
2
Left side
(44.9 x 108.9cm)
P8318
1Right side
(44.9 x 108.9cm)
P8317
2Foldy back
(79.3 x 102.5cm)
B02569
3
Top
(80.3 x 45cm)
P8503
4Bottom
(73.1 x 44.8cm)
P8113
5Drawer bottom x 5
(69.3 x 34.3cm)
BO2760
6
Drawer front x 5
(72.6 x 18.9cm)
P4116
7Plinth back
(73.1 x 9.2cm)
P6109
8
Left drawer side x 5
(35 x 14cm)
LA1614
9Drawer back x 5
(68.2 x 14cm)
LA1649
10 Right drawer side x 5
(35 x 14cm)
LA1615
11
ID-hole

For damaged or missing parts, please visit:
www.argos-support.co.uk or email: [email protected]
Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
7mm Suitable drill bit
(for use with wall plug)
Drill
(For use with wall plug)
0102030405060708090 100 110 120 130 140 150
0123456
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
The screwslength ismeasured from thehead to the point (30mm screw shown).
3
Locking screw x 18 (5x24mm)
FK1011
12mm
Locking nut x 10 (12x10mm)
FK1010
15mm
Large locking nut x 8 (15x12mm)
FK1012
Screw x 70 (3x15mm)
FK1311
Fixing screw drawer x 24 (6.3x10mm)
FK1301
Screw x 10 (4x25mm)
FK1985
Screw x 1 (4x15mm)
FK1400
Nail x 28
FK1515
Expando housing x 4 (20x12mm)
FK1051
Drawer handle x 5
GR1855
Locking screw x 4 (5x11mm)
FK10561
L-Bracket x 1
FK1235
Peg, brown x 1
FK1234
Nail holder x 1
FK1415
Glue x 1
FA1510
Runner left part A x 5
PM1515 LA
Runner left part B x 5
PM1515 LB
Wall plug (6mm) and parkerscrew x 1
ZF99936
Runner right part A x 5
PM1515 RA
Runner right part B x 5
PM1515 RB
Drawer base support x 30
FK1250
Plug, Nylon x 10
FK1800
V
U
T
S
R
Q
P
O
NM
L
KJ
IHG
F
E
D
CB
A
Piercer
(small)

Assembly Instructions
4
Step 1
Finished
front edge
a:
b:
a: Screw 24mm locking
screw Ainto left side 1.
Note: Insert 24mm locking
screw Aas far as shown.
Do not over tighten.
Insert large locking nuts C
into left side 1.
Make sure the ‘arrow’ on
locking nuts Cpoints
towards the hole in the
edge of left side 1.
Screw 11mm locking
screw Jinto left side 1.
Note: Insert 11mm locking
screw Jas far as shown.
Do not over tighten.
Press the Nylon plug P
firmly into left side 1.
Finished
front edge
Attaching runners
b: Fix runner left part A R
on left side 1as shown
usesing fixing screw
drawer Dinto left side 1.
Note: look carreful for the
right postion.
Insert 15mm screw E
as shown into left side 1
to fix runner left part A R.
C
C
A
A
A
C
D D
E E E
P
P
P
P
P
P
R
R
R
R
R
R
J
J
J
1
1

ID-hole
Assembly Instructions
5
Step 2 a:
b:
a: Screw 24mm locking
screw Ainto right side 2.
Note: Insert 24mm locking
screw Aas far as shown.
Do not over tighten.
Insert large locking nuts C
into right side 2.
Make sure the ‘arrow’ on
locking nuts Cpoints
towards the hole in the
edge of right side 2.
Screw 11mm locking
screw Jinto right side 2.
Note: Insert 11mm locking
screw Jas far as shown.
Do not over tighten.
Press the Nylon plug P
firmly into right side 2.
Attaching runners
b: Fix runner right part A T
on right side 2as shown
usesing fixing screw
drawer Dinto right side 2.
Note: look carreful for the
right postion.
Insert 15mm screw E
as shown into right side 2
to fix runner right part A T.
Finished
front edge
Finished
front edge
P
P
P
P
P
P
J
J
J
T
T
T
T
T
T
C
C
A
A
A
C
D D
E E E
2

Assembly Instructions
6
Step 3
Step 4
Step 5
Finished
front edge
Finished
front edge
Insert large locking nuts C
into bottom 5.
Make sure the ‘arrow’ on
locking nuts Cpoints
towards the hole in the
edge of bottom 5.
Insert expando housing I
into Plinth back 8.
Screw 24mm locking
screw Ainto top 4.
Note: Insert 24mm locking
screw Aas far as shown.
Do not over tighten.
A
A
A
A
A
C
C
C
C
C
I
I
I
I
I
4
8
5

Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 6
Step 7
Attaching panels
Position top 4onto left
side 1and right side 2.
Use a screwdriver to turn
locking nuts Cclockwise
to lock.
Position plinth back 8
onto left side 1and right
side 2.
Use a screwdriver to turn
Expando housing H
clockwise to lock.
Attaching panels
Position left side 1and
right side 2onto bottom
5.
Use a screwdriver to turn
locking nuts Cclockwise
to lock.
C
H
C
1
25
8
1
2
4
5

Assembly Instructions
8
Step 8
Step 9
Preparing drawer
Insert locking nuts Binto
left drawer side 9and
right drawer side !.
Make sure the ‘arrow’ on
locking nuts Bpoints
towards the hole in the
edge of left drawer side
9and right drawer side
!.
Put drop of glue Qinto the
3 holes of left drawer side
9and right drawer side !.
Attach left drawer side 9
and right drawer side !
onto drawer back 0.
Insert drawer bottom 6.
Fitting back panel
Attach foldy back 3to the
back with the coloured
surface facing the inside
using nails H.
Use nail holder Oto hold
the nails Hvertical and at
correct distance as you
secure the foldy back 3.
Nails Hshould be spaced
about 150mm apart.
Important:
Furniture MUST
be ‘square’ when
back is attached.
5x
B
B
B
H
H
H
H
H
Q
Q
Q
O
O
3
5
2
9
10
11
6

Assembly Instructions
Position drawer front 7
onto drawer.
Use a screwdriver to turn
locking nuts Bclockwise
to lock.
Note: look carefully to the
positions of drawer front 7.
Fix drawer handle Lonto
drawer front 7using
screw G.
a: Turn over drawer.
Fix runner left part B S
on left drawer side 9as
shown using screw E.
Fix runner right part B U
on right drawer side !as
shown using screw E.
Screw 24mm locking
screw Ainto drawer front
7.
Note: Insert 24mm locking
screw Aas far as shown.
Do not over tighten.
5x
5x
5x
a:
9
Step 10
Step 11
Step 12
A
A
A
B
L
G
G
E
U
S
E
79
10
11
6
9
10
11
6
7