Argos Habitat Winchester Tall TV Unit 414/7990 User manual

MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
Winchester - Tall TV Unit
Assembly Instructions - Please keep for future reference
ALR3163
414/7990
Width - 119.9cm
Depth - 39.4cm
Height - 61.6cm
Issue 1 - 17/07/15

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 36kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
2
80%
x 2 1 2 3
5Base (DF2806)
(112.9 x 37.3cm)
4
Long Rail (DF2805)
(112.9 x 9.2cm) x 4
Front Plinth (DF2810)
(119.1 x 9.2cm)
Side Plinth (DF2386)
(37.4 x 9.1cm) x 2
6
7
9
10
11
12
13
Wide Shelf (DF2822)
(43.3 x 34.9cm) x 2
Narrow Shelf (DF2821)
(33.3 x 34.9cm) x 2
Left Side (DF2815)
(59.4 x 37.4cm)
Right Side (DF2816)
(59.4 x 37.4cm)
Left Divider (DF2818)
(47.2 x 37.2cm)
Right Divider (DF2819)
(47.2 x 37.2cm)
Top (DF3279)
(119.9 x 39.4cm)
Door (DF3280)
(46.6 x 32.7cm) x 2
Small Back (X520-333)
(52 x 33.3cm) Large Back (X520-359)
(52 x 35.9cm) x 2
8
14

Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
3
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D F
G H I
L
C
M
J K
Large locking
nut (F900) x 18
Metal dowel (F901) x 18
Wooden dowel (F22) x 18
25mm Screw (F50) x 6
Plastic Nail (F91) x 6 Hinge plate
(F523) x 4 Hinge (F522) x 4
Shelf stud (F110) x 16
13mm Screw (F63) x 8
E
Bag of Nails
(F51) x 2
Handle
(F463) x 2
38mm Screw (F81) x 2
40mm Screw (F910) x 8
NStrap Screw Washer x 2
Overbalance protector kit (F269) x 1
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver

D
D
Finished
front edge
D
D
Assembly Instructions
4
Step 1
x 2
Prepare the left
divider
Tap 2 wooden dowels
into the left divider .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Step 2
Step 3
B
B
Finished
front edge
B
B
Prepare the base
Insert 4 large locking
nuts into the base .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
B6
6
10mm
D
D
3
Prepare the right
divider
Tap 2 wooden dowels
into the right divider .
D
4
3
4
B
Finished
front edge

Finished
front edge
D
D
Finished
front edge
D
D
Assembly Instructions
5
Step 4
Fit the base
Attach the base to
the left divider and
right divider with 4
screws .
6
3
4
F
Step 5
Finished
front edge
F
F
F
F
6
B
A
A
A
AA
B
K
K
K
Prepare the left side
Screw 6 metal dowels
into the left side .
Insert 2 large locking
nuts into the left side
. .
Tap 2 wooden dowels
into the left side .
Fit 2 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
K
1
A
B
1
1
D
1
A
Step 6
Prepare the right side
Screw 6 metal dowels
into the right side .
Insert 2 large locking
nuts into the right
side .
Tap 2 wooden dowels
into the right side .
Fit 2 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.
K
2
B
2
2
D
2
A
1
B
B
A
A
A
A
A
A
K
K
K
Finished
front edge
2
3
4

F
F
F
F
Assembly Instructions
6
Step 7
D
x 4
Prepare the 4 long rails
Insert 2 large locking
nuts into each of the
long rails .
Tap 2 wooden dowels
into each of the long rails
. .
B
9
D
9
B
B
D
9
Finished
front edge
Fit 2 long rails
Push 2 long rails
onto the dividers and
. secure them with 4
screws .
Step 8
F
9
3
49
9
3
4
Step 9
Fit the right side
Push the right side
onto the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the base and the 2
long rails .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
B
B
6
9
6
9
9
2
A
B

Assembly Instructions
7
Step 10
Step 11
2
Fit the other long rails
Push the 2 long rails
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the long rails .
B
9
9
2
9
9
9
9
Note: Fit the long rail at
the back last and support it
until the left side has been
fitted in the next step.
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 6 large
locking nuts fitted to
the base and the 4
long rails .
1
B
6
91
9
9
6

Polystyrene
block
Polystyrene
block
Polystyrene
block
Polystyrene
block
Assembly Instructions
8
Step 12
Prepare the top
Screw 4 metal dowels
into the top .
Step 13
A
5
Fit the top
Note: To make it easier
to fit the top and plinths,
place polystyrene blocks
from the packaging
underneath the side
panels to raise the
assembly.
Push the top onto
the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the sides and .
Warning: The
unit is heavy.
Lift with care.
5
1 2
B
A
A
A
A
Rounded
front edge
5
5
1
2

yy
xx
yy
Assembly Instructions
9
Step 14
Step 15
Fit the 3 backs
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the small back
. in the centre of the
unit and nail along the
top and bottom edges.
Place the 2 large backs
. onto the unit as
shown and nail
around the outside
edges.
Note: Nails should be
spaced about 150mm
apart.
13
E
E
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
These gaps are for
cable management
a:
14
Fit the 6 plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
Tap a plastic nail into
the bottom edge of each
of the long rails
fitted at the bottom
of the unit.
J
1
J
9
2
xx
b:
E
13
14
14
J
J
J
J
J
J1
9
9
2