Argos Sparkle User manual

MADE IN
BRITAIN
Dimensions
Width - 75.1cm
Depth - 39.6cm
Height - 90.1cm
Sparkle - 5 Drawer Chest
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 03/06/15
Important - Please read these instructions fully before starting assembly
ALR3198
412/1961
402/3124
395/7655

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 31kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
80%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
12
3
5 6 Left Drawer Side (W370-124LH)
(37 x 12.4cm) x 5
Right Drawer Side (W370-124RH)
(37 x 12.4cm) x 5
7
4
8
9 10
Left Side (DF3867)
(88.6 x 37.2cm)
Rail (DF3813)
(71.7 x 6cm) x 3
Right Side (DF3868)
(88.6 x 37.2cm)
Top (DF3812)
(75.1 x 39.6cm)
Drawer Front (DF3814)
(73.7 x 16.2cm) x 5
Drawer Back (W684-124)
(68.4 x 12.4cm) x 5
Drawer Base (T695-367)
(69.5 x 36.7cm) x 5
Back (X861-743)
(86.1 x 74.3cm)

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D E F
G H I
L
Small locking
nut (F3) x 10
C
Nail (F51) x 25
M
J
9mm Screw (F74) x 10
K
9mm Screw (F73) x 20
Drawer runner (F1004) x 10
Knock-in Peg (F171GY) x 20
Large locking
nut (F900) x 10
Metal dowel (F901) x 20
Wooden dowel (F22) x 10
Wedgefix (F639) x 20
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
25mm Screw (F50) x 15
Plastic Nail (F91) x 4
Handle (F569) x 5
NStrap Screw Washer x 2
Overbalance protector kit (F269) x 1
Electric drill
(only use
when drilling
into walls)

5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
80%
x 2
x 5
x 5
x 5
x 5
A
A
C
C
C
C
67
Step 2
Prepare the 5 drawer
fronts
Screw 2 metal dowels
into each of the drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
A
5
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
6
7
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
6
7
5
C
C
6
7
6
7
A
A
5

5
Assembly Instructions
5
Step 3
F
F
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
9
6 7
5
8
6 7
9
8
8
F
Attach the handles
Attach a handle to
each of the drawer fronts
. using screws .
Note: Do not
overtighten the screws.
L
G
5
6 7
Step 7
Fit the wedgefixes
Turn the 5 drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
K
x 5
x 5
x 5
F
F
x 5
K
K
K
K
K
9
6
8
6
7
9
7
G
G
G
L
5

Finished
front edge
Finished
front edge
Finished
front edge
D
D
Assembly Instructions
6
Step 8
Prepare the left side
a: Place 5 runners on
the left side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
c: Screw 3 metal
dowels into the left
side .
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nuts must point
towards the hole in the
edge of the panel.
Tap 2 wooden dowels
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels. B
1
I
I
B
1
1
M
M
A
1
D
1
a:
b:
c: 10mm
D
I
M
I
M
I
M
I
M
I
M
I
M
I
I
I
I
I
A
A
A
B
B
1
1
1

D
D
Assembly Instructions
7
Step 9
Prepare the right side
a: Place 5 runners on
the right side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
c: Screw 3 metal
dowels into the right
side .
Insert 2 large locking
nuts into the right
side .
Tap 2 wooden dowels
into the right side .
2
I
I
I
M
B
2
2
M
M
A
2
a:
b:
c:
D
2
I
M
I
M
I
M
I
M
I
MFinished
front edge
2
Finished
front edge
2
Finished
front edge
2
I
I
I
I
I
A
A
A
B
B

Finished
front edge
D
Assembly Instructions
8
Step 10
x 3
Prepare the 3 rails
Insert 2 large locking
nuts into each of 3
the rails .
Tap 2 wooden dowels
into each of 3 the rails .
B
4
D
4
A
B
Fit the the 3 rails to
the right side
Push the 3 rails onto
the right side .
Use a screwdriver to
tighten the large locking
nut fitted to each of
the rails .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
4
B
B
4
Step 11
Fit the left side
Push the left side
onto the rails .
Use a screwdriver to
tighten the large locking
nut fitted to each of
the rails .
4
1
B
4
Step 12
B
B
D
4
Note: Support
these 2 rails
until the left side
has been fitted
in the next step.
4
4
4
2
4
4
4
1

Finished
front edge
Assembly Instructions
9
Step 13
Prepare the top
Screw 4 metal dowels
into the top .
A
3
Fit the top
Push the top onto
the assembly.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each of the sides and
. .
3
B
1
2
Step 14
Step 15
Fit the 4 plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
J
1
2
A
A
A
A
Finished
front edge
3
3
1
2
J
JJ
J
1
2