Argos Eden 397/6540 User manual

MADE IN
BRITAIN
Dimensions
Width - 119.5cm
Depth - 38.5cm
Height - 47cm
Eden - TV Unit
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 2 - 01/06/15
Important - Please read these instructions fully before starting assembly
ALR3155
397/6540
399/9204
Issue 2 - 01/06/15 - Fitted Shelf Studs to screw up into the Shelf.
Altered the assembly so that the Back is fitted with the unit upright.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 17kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
12 3
80%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
4
Left End (DF3439)
(396 x 375mm)
Door (DF1191)
(325 x 389mm)
Right End (DF3440)
(396 x 375mm)
Top (DF3441)
(1195 x 381mm)
Shelf (DF3443)
(689 x 354mm)
Base (DF3442)
(1119 x 369mm)
Divider (DF1190)
(331 x 363mm)
Back (DF1517)
(395 x 331mm)
5
7
6
8

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D E F
G H I
C
J
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Small metal dowel (F893) x 12
Hollow core
locking nut
(F892) x 12
19mm Screw (F461) x 2
Handle (F414) x 1
Wooden dowel (F22) x 4
13mm Screw (F63) x 4 Shelf stud (F372) x 4
Door stop (F110) x 1 Hinge plate
(F523) x 2 Hinge (F522) x 2

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
C
C C
Prepare the base
Push 4 hollow core
locking nuts into the
base , making sure
that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Note: The pin should be
tapped in flush with the
top surface of the hollow
core locking nut .
Turn the base over
Screw 2 small metal
dowels into the base
. .
Note: Tighten metal
dowels up fully against
the panels.
C
C
5
C
B
5
B
C
C
C
C
B
B
Turn the base over
5
5

Assembly Instructions
5
Step 2
Step 3
Finished front edge
2
4
Step 3
Fit the base to the
right end
Push the base onto
the right end .
The 2 small metal dowels
. fitted to the right end
. must slide into the
top of the 2 hollow core
locking nuts fitted to
the base . .
Insert a screwdriver into
the 2 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
B
C C
2
5
B
2
C
5
C
2
5
C
C
B
F
F
Prepare the left end
Push 2 hollow core
locking nuts into the
left end , making sure
that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Screw 2 small metal
dowels into the left
end .
Push 2 shelf studs
into the left side .
C
C
1
B
1
1
B
B
F
1
Fit the left end to the
base
Push the left end
onto the base .
The 2 small metal dowels
. fitted to the left end
. must slide into the
top of the 2 hollow core
locking nuts fitted to
the base . .
Insert a screwdriver into
the 2 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
1
5
B
1
C
5
C
1
B
C C
5

3
Assembly Instructions
6
Step 4
5
Step 5
Fit the left end
Push the left end
onto the base .
The 2 small metal dowels
. fitted to the left end
. must slide into the
top of the 2 hollow core
locking nuts fitted to
the base . .
Insert a screwdriver into
the 2 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
1
5
B
1
C
5
C1
Prepare the divider
Push 2 shelf studs
into the divider .
Turn the divider over
Push 4 hollow core
locking nuts into the
divider , making sure
that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Step 5
C
C
3
F
3
C
C
C
C
3
Step 8
Fit the back to the
divider
Push the back onto
the divider .
3
6
6
3
Turn the divider over
185.5mm
5
Top edge
Top edge
Fit the divider
Push the divider onto
the base .
The 2 small metal dowels
. fitted to the base
must slide into the top of
the 2 hollow core locking
nuts fitted to the
divider . .
Insert a screwdriver into
the 2 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
3
5
B
3
C
5
C
3
F
F

Assembly Instructions
7
Step 6
Finished front edge
2
4
Step 7
Fit the divider
Push the back into
right side and the
divider onto the base
. .
The 2 small metal dowels
. fitted to the divider
. must slide into the
top of the 2 hollow core
locking nuts fitted to
the base . .
Insert a screwdriver into
the 2 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
6
3
5
2
B
3
C
5
C
6
3
5
2
Prepare the top
Screw 6 small metal
dowels into the top
. .
B
B
B
B
B
B
B
4
4
1
Fit the top
Push the top onto the
left side and divider
. .
The 4 small metal dowels
. fitted to the top
must slide into the top of
the 4 hollow core locking
nuts fitted to the left
side and divider . .
Insert a screwdriver into
the 4 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
4
1
3
B4
C
1 3
C
A
A
A
A
10mm
A
Prepare the back
Tap 4 wooden dowels
into the back .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
A
6
6
Step 8
3
4

Assembly Instructions
8
Step 9
Step 10
Fit the back
Carefully stand the unit
upright and push the
back into the divider
. .
1
Prepare the right end
Push 2 hollow core
locking nuts into the
right end , making
sure that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Screw 2 small metal
dowels into the right
end .
Fit 2 hinge plates onto
the right end , making
sure that the slot is
facing towards the
finished front edge.
C
C
2
B
2
H
2
C
C
B
B
H
H
H
2
6
3
6
3
6
3
Warning: The
unit is heavy.
Lift with care.

Assembly Instructions
9
Step 11
Finished front edge
2
4
Step 12
2
Secure the right end
to the base
Carefully lay the unit
back down onto its front
edges.
Insert a screwdriver into
the 2 hollow core locking
nuts on the base
and turn the nuts inside
as far as they will go.
C5
2
5
Fit the right end
Push the right end
onto the top , base
and back .
Insert a screwdriver into
the 2 hollow core locking
nuts on the right end
. and turn the nuts
inside as far as they will
go.
6
2
4 5
C
2
4
5
6