Argos Arizona 461/6366 User manual

Arizona Dining Table
Assembly Instructions - Please keep for future reference
Issue 1 - 12/05/16
Length - 140cm
Width - 90cm
Height - 76cm
Dimensions
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
461/6366

1
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product, this
could cause damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Unit weight: 22.1 kgs.
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
Handy Hints
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• Do not stand on the product.
• Always lift the product when
moving it around. Never drag.
• Please note wood is a natural
material, some slightly colour
and grain variation and natural
marks will be present.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• Regularly check and ensure
that all bolts and fittings are
tightened properly.

2
Components - Parts
Please check you have all the parts listed below
Table top
(140 x 90 x 11cm)
1Leg x 4
(8 x 8 x 72cm)
2
If you have damaged or missing components, call the
Customer Helpline: Argos = 0345 640 0800
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Tools required
Stud bolt x 8
A
Barrel nut x 4
B
Nut x 8
C
Flat washer x 8
D
E
Spring washer x 8
F
Spanner x 1
G
Foot Pads x 4
Flathead screwdriver

3
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
2
2
1
2
2
Step 1
a: Attaching insert nut
Insert the barrel nut
into the hole on top of the
leg as shown.
b: Attaching stud bolts
Align the fixing holes on
the barrel nut by
turning it using a flathead
screwdriver.
Then fix stud bolts into
the barrel nut on leg
as shown.
Repeat this step to
assemble the other
legs.
A
A
A
A
B
B
B
B
A
a: b:
2
2
2
2
2
Attaching legs
Place the table top on
a flat protected surface.
Position the legs on
the table top as shown.
Insert the stud bolts
assembled in previous
step into holes on table
top.
Then fix using nuts ,
spring washers and
washers . Tighten nuts
using spanner .
Carefully turn over the
table and place on a firm
surface.
At least 2 people are
required to lift this table.
Assembly is complete.
Step 2
2
1
D
F
E
C
2
1
D
E
C
D
E
G
G
G
G
C
Remove backing from
foot pads and carefully
position on the bottom of
the legs as shown.
G
2
G
2