Argos Nest of Tables 609/1439 User manual

Nest of Tables
Assembly Instructions -
Please keep for future reference 609/1439
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Dimensions
Depth - 40/30cm
Width - 56/40cm
Height - 47/35.5cm
Large / Small
609/1893
Version 2 Date: 03/10/11
609/3688
609/6300

Glue safety - Take care when using glue, please follow the advice below
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
• Check you have all the
components and tools listed on
pages 2 and 3.
rom the
plastic bags and separate them
into their groups.
• Keep children and animals away
from the work area, small parts
could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand on the product,
this could cause damage.
• Assemble the item as close to
room) as possible.
• Assemble on a soft level surface
to avoid damaging the unit or your
r.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Note: Only apply the glue once
you are sure of the assembly.
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority waste
disposal centre.
1

2
Components - Panels
Please check you have all the panels listed below
Large table top (56 x 40cm)
1
Small table top (40 x 30cm)
2
Large support x 2 (43.8 x 6cm)
3
Medium support x 4 (27.8 x 6cm)
4
Small support x 2 (17.8 x 6cm)
5
Large leg x 4 (45.5 x 4.5cm)
6
Small leg x 4 (34 x 4.5cm)
7
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Pilot holes for
guidance only
Pilot holes for guidance only
Pilot holes for guidance only
Pilot holes for
guidance only
Pilot holes for
guidance only

3
Note: The quantities below are the correct amount to complete the assembly. in some cases mor
may be supplied than are required.
110 120 130 140 1500 10 20 30 40 50 60 70 80 90 100
0 1 2 3 4 5 6
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Dowel x 24
Components - Fittings
Locking pin x 16 14mm Screw x 20
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Bradawl
(or sharp point)
Drill
7mm Masonary drill bit
(for use with wall plug)
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
Ruler - Use this ruler to help correctly identify the screws
ABC
15mm Locking nut x 16
DEF
Glue x 1
Q
Plastic support x 10

4
a:
Assembly Instructions
Step 1
Fitting the legs
b:
b:
onto the Large support
Locking nuts
Locking nuts
Large legs
.
D
6
3
Note:
assembly the other legs.
Follow the same
Note: It would be useful
to ask
someone to help
you at this stage.
a: Place a small amount
of Glue into the dowel
holes. Insert Dowels
into the Large and Medium
, Small supports and
, .
B
F
Note: The screw holes
on the legs and support
should align.
Note:
Small legs onto the
Medium supports .
For small table, use
4
D
7
Use a screwdriver to turn
Locking nuts clockwise
to lock.
D
b to
Continued on next page.
A
F
D
D
B
B
6
3
4
A
A
A
A
D
D
B
5
A
A
3
A
F
6
6
7
B
B
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
Screw in Locking pins
into the Large and Small
legs and .
A
6 7
3
4 5

5
Assembly Instructions
Step 1 - continued
c:
c:
the Medium support .
Large legs
Locking nuts
6
D
4
Note: For small table,
replace with Small legs
, replace with Small
supports .
Note: The screw holes
on the medium supports
or small supports should
face inward.
6
4
5
7
Use a screwdriver to turn
Locking nuts clockwise
to lock.
D
6
6
6
6
4
4
D
D
D
D
D
D
A
F
Continued on next page.
Step 2
a:
6
6
6
6
A
A
A
A
A
F
Fitting the table top
a: Place a small amount
of Glue into the dowel
holes. Insert Dowels
fully into the Large legs
.
F
6
A
Note: For small table,
repeat with Small legs .
7

Step 2 - continued
b:
c:
Plastic supports onto
the Large table top
and unit.
E
1
C
1
C
C
E
Carefully locate the
Large table top onto
the unit.
1
Note: For small table,
replace with Small
table top .
1
2
Note: For small table,
replace with Small
table top .
1
2
C
C
E
c:
b:
6
Assembly Instructions
1

7
Assembly Instructions
Step 3
Finishing the unit
Carefully turn the table
upright.
Large table
Small table
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Assembly is complete.
Note:
Before use allow the
Glue to dry for 24 hours
and make sure the unit is
secure.
It would be useful
to ask someone to help
you at this stage.
Note: