Argos Malibu Tall Unit 833/7115 User manual

MADE IN
BRITAIN
Dimensions
Width - 30cm
Depth - 28cm
Height - 147cm
Malibu Bathroom - Tall Unit
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 07/08/13
Important - Please read these instructions fully before starting assembly
ALR2869
833/7115
Issue 2 - 07/08/13 - Added a Door buffer to the fittings page.
Step 21 amended to show it being fitted.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 14.5 kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
1
Top (D2129A)
(300 x 280mm)
Base (D2132A)
(260 x 276mm)
Plinth (D2135A)
(260 x 145mm)
6
7
2
4
5
3
8
Left End (D2136A)
(1447 x 278mm)
Fixed Shelf (D2138A)
(260 x 260mm)
Loose Shelf (D2133A)
(260 x 260mm) x 2
Right End (D2137A)
(1447 x 278mm)
Door (D2139A)
(534 x 254mm)
9Back (X966)
(1313 x 286mm)

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 2
B
Metal dowel (F901) x 14
C
F
G H I
L
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J K
see malibu fitment mk2 for large number of panels and fittings
Electric drill
(do not use for
fitting screws)
Large locking
nut (F900) x 14
D
25mm Screw (F50) x 1
Nail (F51) x 22
E
Bracket (F327) x 1
13mm Screw (F79) x 1 13mm Screw (F63) x 4
Shelf support (F121) x 8
N
Door Buffer (F137) x 1
Plastic Nail (F91) x 4
M
Handle (F631) x 1
Hinge plate
(F523) x 2 Hinge (F522) x 2

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Step 2
Choose which way
you would like the
door to open
You can fit the door to
the left side or right side.
If you would
like your door
to open this
way, fit the
hinge plates
to the left side
If you would
like your door
to open this
way, fit the
hinge plates to
the right side
Prepare the left end
Refer to step 1 and, if
required, fit 2 hinge
plates onto the left
end , making sure
that they face the same
way as the diagram.
Screw 5 metal dowels
into the left end .
Note: Tighten the metal
dowels up fully against
the panels.
Insert 2 large locking
nuts into the left end
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
B
1
C
1
C
K
B
K
1C
C
K
K
BB
B
B
B
1

Assembly Instructions
5
Step 3
Step 4
C
C
B
Prepare the right end
Refer to step 1 and, if
required, fit 2 hinge
plates onto the right
end , making sure
that they face the same
way as the diagram.
Screw 5 metal dowels
into the right end .
Insert 2 large locking
nuts into the right
end .
B
2
C
2
K
22
K
B
B
B
B
K
K
Join the right end and
base
Push the base onto
the right end .
Note: The back edges
must be flush.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Step 5
C
C
C
C
Prepare the base
Insert 4 large locking
nuts into the base .
C44
4
2
C
4
C
4
B
C
2
4
2
Note: The base is larger
than the fixed shelf
(refer to the components page)

Assembly Instructions
6
Step 6
Prepare the fixed
shelf
Insert 4 large locking
nuts into the fixed
shelf .
C
C
C
C
5
5
Fit the fixed shelf
Push the fixed shelf
onto the right end .
Note: The back edges
must be flush.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the fixed shelf .
Step 7
5
2
C
5
2
5
2
5
A
Step 8
C
C
A
10mm
A
Prepare the plinth
Tap 2 wooden dowels
into the plinth .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking
nuts into the plinth .
A
6
6
C6

Assembly Instructions
7
Step 9
Step 10
2
6
Fit the plinth
Push the plinth onto
the right end .
Use a screwdriver to
tighten the large locking
nut fitted to the plinth
. .
6
2
C
6
6
Fit the left end
Push the left end
onto the assembly.
Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the base , fixed shelf
. and plinth .
1
4
5 6
C
1
4
5
Step 11 B
B
B
B
3
Prepare the top
Screw 4 metal dowels
into the top .
B
3

3
Assembly Instructions
8
Step 12
Step 13
Fit the top
Push the top onto
the assembly.
Note: The back edges
must be flush.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the left end and right
end .
1
2
C
3
2 3
1
2
E
J
J
3
3
I
I
I
I
Fit the bracket and
the plastic nails
Fix the bracket in the
middle of the top ,
flush to the back edge,
using screw .
Tap the 4 plastic nails
into the bottom edge of
the left end and right
end .
J
3
E
I
1
2
1
2

y
Assembly Instructions
Step 14
Step 15
J
Secure unit to a wall
To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by use of the metal
bracket fitted to the
top .
Fixings are not supplied
as they will need to suit
the wall type, and the
length of screw will
depend on the distance
of the back of the unit to
the wall.
Warning: Take
care when
drilling the wall that you
do not drill into any
pipes, wires etc. If in
doubt, consult an expert.
3
J3
WALL
WALL
Top of unit
J
b:
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of
the back .
Note: Nails should
be spaced about
150mm apart.
Stand the unit up
for the next step.
9
G
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
9y
x
G
Warning: The
unit is heavy.
Lift with care.
y
x
9
9