Argos Jenson User manual

Spare Parts
Visit: www.argos-support.co.uk
Email: [email protected]
Call: 0330 016 1114
Customer Support
Call: 0345 640 2020
JENSON
Gloss
941/7481 853/5890
Issue 1 - 11/12/20

Safety
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 43kgs.
Please lift with care.
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Installation shall only be
carried out exactly according to
the manufacturer’s instructions -
otherwise a safety risk can
occur if incorrectly installed.
• Do not use this item if any
components are missing or
damaged.
Care Advice
• Check you have all the
components and tools listed on
relevant pages.
• Remove all fittings from the
specified plastic bag and
separate them into their groups.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• WARNING: To prevent
possible overbalancing this unit
must be secured to a wall using
the 2 overbalance protector kits
supplied.
• A unit that is allowed to topple
can cause serious or fatal injury.
In addition to wall fixing the unit,
place heavy items on the lower
shelves, do not put any heavy
objects on top of the unit and
never allow children to climb or
hang on drawers, doors or
shelves.
• Refer to guide after section 36
for wall fixing information.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Assembly videos are
available throughout
these instructions by
scanning in the QR
codes.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean with a damp cloth.

Cabinet Panels Please do NOT remove any protective film until after assembly
142.3 x 42.9cm 446.9 x 41.4cm x 2
9147.5 x 36.5cm
10 149.9 x 45.0cm
11 49.7 x 39.6cm
242.3 x 42.9cm
546.9 x 6.0cm x 4
12 49.5 x 32.7cm
342.3 x 41.5cm
642.3 x 41.5cm
DF-00022936
DF-00022930
749.7 x 41.4cm
DF-00022932
DF-00022935
DF-00022929
849.7 x 6.0cm x 2
DF-00022931
XDF-00022923
DF-00022823
DF-00022922
DF-00022934
DF-00022834
DF-00022833

Drawer Panels Note: the internal drawer panels are grey
Please do NOT remove any protective film until after assembly
13 49.5 x 32.7cm 14 40.0 x 14.0cm
DF-00022926
17 43.65 x 14.0cm
WRP-00000486
WRP-00000430
15 40.0 x 14.0cm
WRP-00000429
16 44.75 x 39.7cm
TDF-00022937
x 2
x 2 x 2
x 2
x 2

Fittings Use these drawings to
correctly identify the fittings
Bag 1
Bag 2
F22
Cx 16
F137
Kx 6
F901
Bx 16
F901
Bx 8
x 13
J
F51
Lx 8
F646
Fx 4
F63
F639
Ix 9
F639
Ix 8
F900
Ax 32
F607
Mx 8
F110
Hx 4
F40
Ex 8
F566
Dx 8
Gx 8
F73
Ox 8
F171GY
Nx 4
F74
Tools
Only used for
drilling walls

Qx 2
F328
Rx 4
F450
F474
Px 2
Tools
Only used for
drilling walls
Fittings Use these drawings to
correctly identify the fittings

1
2
2nd hole
1
2
1
www.youtube.com/watch?v=yG4xtiJJeSg
Fitting Ball Bearing Runners
Gx 2 Rx 2
2nd hole
2
Gx 2
Finished
front edge
Finished
front edge
Bag 1
F22
Cx 16
F137
Kx 6
F901
Bx 16
x 13
J
F51
Lx 8
F646
Fx 4
F63
F639
Ix 9
F900
Ax 32
F110
Hx 4
F40
Ex 8
F566
Dx 8
Gx 8
F73

Finished
front edge
Finished
front edge
3
4
Cx 4
5
Ax 4
Bx 8
1
2
1
2
1
2

3
6
3
Ax 2 Cx 2
Finished
front edge
7
Gx 1 Rx 1
www.youtube.com/watch?v=yG4xtiJJeSg
Fitting Ball Bearing Runners
Finished
front edge

10
Finished
front edge
Finished
front edge
9
4
4
Ax 4 Cx 2
Finished
front edge
3
2nd hole
8
Gx 1
x 2
2

11
12
Ax 4 Cx 2
4
2
5
5
5
5
x 2

3
3
13
D
F
Ex 4
14
Finished
front edge
x 2
x 2
x 4
D

15
6
Ax 2 Cx 2
Finished
front edge
2nd hole
6
16
Gx 1 Rx 1
www.youtube.com/watch?v=yG4xtiJJeSg
Fitting Ball Bearing Runners
Finished
front edge

18
19
7
7
Finished
front edge
Finished
front edge
Ax 4
6
17
Gx 1 2nd hole
x 2

8
8
8
8
20
21
Ax 4
x 2

22
Ex 4
6
6
23
Finished
front edge
x 4
D
x 2
x 2

24
25
4
4
Ax 4 Cx 2
Finished
front edge
Finished
front edge
x 2

26
27
5
5
5
5
Ax 4 Cx 2
x 2

28
29
1
x 8
L
Finished
front edge
x 2

30
31
www.youtube.com/watch?v=FeaI6541z7o
Squaring up a Chest and fitting the Back Panel
A = B
Make sure measurement
A and B are the same
The Back panel must be
flush with the Back Rail.
A
B
9
9