Argos SCHREIBER 6324852 User manual

Issue1-9/26/10
Dimensions
Width –1925
Depth – 2380
Height –1205
09H SCH LANCELOT 6FT FRAME
AssemblyInstructions–Pleasekeepforfuturereference
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800
6324852
SCHREIBER

1
yCheckyou have all the
Components and tools listed on
Pages 2 and 3.
yRemove all fittings from the
Plastic bags and separate them
Into their groups.
yKeep children and animals
Away from the work area, small
Parts could choke if swallowed.
yMake sure you have enough
Space to layout the parts before
Starting.
yDo not stand or put weight on
The product during assembly,
this could cause
Damage.
yAssemble the item as close
To its final position (in the same
Room) as possible.
yAssemble on a soft level
Surface to avoid damaging the
unit or your floor.
yParts of the assembly will be
easier with 2 people.
yWe do not
Recommendthe
use of power
drill/drivers for
inserting screws.
As this could damage the unit
Only use hand screwdrivers.
yDispose of all packaging
Carefully and responsibly.
Skin contact: Remove
Contamination by washing with soap
and water. This procedure should
also be followed prior to eating and
drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advic.
If swallowed: Seek medical advice
immediately.
yOnly clean using a damp cloth and
mild detergent, do no use bleach or
abrasive cleaners.
yFrom time to time check that
there are no loose screws on this
unit.
yThis product should not be
discarded with household waste.
Take to your local authouity waste
disposal centre.
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Glue safety – Take care when using glue, please follow the advice below
Care and maintenance

2
Components - Panels
Please check you have all the panels listed below

□
1Headboard *1 (1925*1205*220) mm □
2 Footboard *1 (1930*655*150) mm
□
3 Cross Bar *2 (2010*160*50) mm
□ 4 Center rail *2 (1763*78*25) mm
□ 5 Side rail *2 (1893*25*25) mm
□ 6 End rail *2 (1769*78*25) mm
If you have damaged or missing components
call the Customer Helpline:0845 6400800
□
7 Slat*42 (600*60*10) mm
□
8 Drawer front *4 (990*150*40) mm
□
9 Drawer side *8 (598*104*16) mm
□
10 Drawer back *4 (822*104*16) mm □
11 Drawer base *4 (855*598*16) mm
□
12 Support Leg *6 (Φ19*285) mm

3
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Please check you have all the fitting listed below
M8*35mm Bolt*6
5MM wrench*1
Tools required
Ruler/tape measure
Components - Fittings
M6*20mm Bolt *16 Φ4*30mm Screw *64
Φ8 washer *6 Φ4*16mm Screw *64
Phillips screwdriver
(medium & large)
30mm Wooden dowel*64
Plastic center cap*32 Plastic end cap*32 Wheel*16
4MM wrench*1
Rubber hammer

4
Assembly Instructions
Fitting bed side
a: Loosen the bolts on the
head&footboard & .
NOTE: Merely loosen the bolts. Do
not take out.
b:Fix the side rails to the head
&footboard & .
b: Use a wrench to tighten bolts.
Two people are needed here.
Fitting slats
Two people are needed here.
a: Use the bolts to fix the
center rail end rail side
rail
Use a wrench to tighten bolts.
Step 1
Step 2
a:
b:
a: