Argos Seville 151/3297 User manual

Assembly Instructions - Please keep for future reference
Ruler - Use this ruler to help correctly identify the screws
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
MADE IN
BRITAIN
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928
or email: [email protected] (quoting your original order number)
Important - Please read these instructions fully before starting assembly
Dimensions
Width - 66cm
Depth - 33cm
Height - 58cm
Seville - 3 Drawer Chest
Issue 2 - 25/03/14
ALR2907
151/3297
170/2187
166/5413
161/7739
Issue 2 - 25/03/14 - Changed Drawer Base to “White : TSAV (T608-299)”

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 14kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

2
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
[email protected] (quoting your original order number
and the reference numbers below)
1 2 Top (D2488A)
(627 x 327mm)
Plinth (D2491A)
(627 x 80mm)
Drawer Front (D2492A)
(623 x 157mm) x 3
Drawer Base White : TSAV(T608-299)
(608 x 299mm) x 3
Back (X328-653)
(328 x 653mm)
Left Side (D2489A)
(576 x 328mm)
4
Right Side (D2490A)
(576 x 328mm)
3
7 8
6
5
Drawer Wrap (WSAV)
(1221 x 95mm) x 3

3
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Tools required
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
[email protected] (quoting your original order number
and the reference numbers below)
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
A
Wooden dowel (F22) x 4
B
Metal dowel (F901) x 6
C
D E F
G
Small locking
nut (F3) x 6
Nail (F51) x 1540mm Screw (F910) x 6
Handle (F300) x 6
HR (F601)
L (F600)
F599
F599
Drawer stops (F599) x 6
Runners (F600) x 3 and (F601) x 3
25mm Screw (F95) x 6

4
F
Step 1
Assembly Instructions
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
[email protected] (quoting your original order number
and the reference numbers below)
x 3
B
B
B
5
x 3 x 3
x 3
C
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
C
6
7
Step 2
C
6
C
7
Step 3
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
6
7
5
C
6
7
B
B
C
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on
either surface of the drawer sides.
Make sure that the small groove
is on the inside, as shown.
5
6
7
Small
groove
C
x 3
Prepare the drawer
fronts
Screw 2 metal dowels
into each of the drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panel.
B
5
6
C
6
C
C
x 3
Fit the drawer base
Place the drawer base
into the narrow slot on
the drawer wrap .
Fold the wrap around the
drawer base.
7
7
6
6
Step 3
Prepare the drawer
wraps
Insert 2 small locking
nuts into each of the
drawer wraps .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 2
C
6
Note: Due to the manufacturing
process, the holes for the
locking nut can be on either
surface of the drawer wrap.
Note: The locking nuts can be on
either surface of the drawer sides.
Make sure that the small groove
is on the inside, as shown.
Plain chipboard
surface

Assembly Instructions
5
Step 4
Attach the handles
Attach 2 handles to
each of the 3 drawer
fronts using 2
screws .
Note: Do not
overtighten the screws.
G
E
Step 6
Step 5
x 3
5G
E
G
E
Attach the drawer
stops
Carefully break off 2
drawer stops (F599) from
a set of drawer runners
. .
Push the drawer stops
fully through the drawer
wrap from the inside.
H
6F599
H
F599
H
x 3
SNAP!
SNAP!
F599
H
H
F599
H
x 3
Fit the drawer front
Turn drawer wrap
assembly over and push
it onto the back of the
drawer front .
Note: Turn the locking
nuts clockwise to
secure the panels - more
than 1/2 a turn.
6
C
5
6
6
6
B
B
C
5
5
5

Finished
front edge
Assembly Instructions
6
Step 7
Prepare the left side
Separate the runners .
Push fit the 3 left runners
. marked ‘L’ into the
left side .
Note: Runners must be
be fitted flat against the
panel. If necessary
gently tap into final
position.
H
H
1
Prepare the right side
Push fit the 3 right
runners marked ‘R’
into the right side .
Note: Runners must be
be fitted flat against the
panel. If necessary
gently tap into final
position.
I
2
Step 8
L
F600
H
H
H
H
1
R
F601
I
I
I
I
2
Finished
front edge
Finished
front edge
A
A
Prepare the top
Tap 2 wooden dowels
into the top .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
A
3
plain chipboard surface
3
Step 9
10mm
A

Finished
front edge
D
D
Assembly Instructions
7
Step 10
Join the top to the
right side
Push the top onto
the right side and
secure with 2 screws .
Step 11
3
2
D
3
2
Prepare the plinth
Tap 2 wooden dowels
into the plinth .
Step 12
A
4
A
A
plain chipboard surface
4
Finished
front edge
D
Join the plinth to the
right side
Push the plinth onto
the right side and
secure with screw .
4
2
D
4
2
Support the plinth
until the left side
has been fitted in
the next step.

Assembly Instructions
8
Step 13
Step 14
4
Fit the left side
Push the left side
onto the assembly and
secure with 3 screws .
D
D
1
D
D
1
yy
xb:
F
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the 3
edges of the back as
shown.
Note: Nails should
be spaced about 150mm
apart.
Stand the unit up for
the next step.
8
F
8
x
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
8

Assembly Instructions
9
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928
or email: [email protected] (quoting your original order number and the reference numbers on the component pages)
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 15
Insert the drawers
Lift the front of the
drawers whilst inserting
to overcome the ‘stop’
system.
Note: To ensure that
your drawers run
smoothly, spray a small
amount of furniture
polish into the grooves.
Assembly is complete