Argos Normandy User manual

MADE IN
BRITAIN
Dimensions
Width - 100cm
Depth - 40cm
Height - 74cm
Normandy - Dressing Table and Stool
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 3 - 16/01/15
Important - Please read these instructions fully before starting assembly
ALR3084
325/6208
331/1837
356/1962
Issue 2 - 07/01/15 - The Drawer Wrap was loose.
The Stool Drawer Back and Stool Drawer Base have increased by 4mm and the drillings for the Stool Drawer Front have changed.
Issue 3 - 16/01/15 - Removed“Finished edge”from the Uprights in Steps 13,14 and 16.
Update helpline number.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 31.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance kit supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
12
80%
x 2
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Top (DF631)
(999 x 396mm)
Left Side (DF632)
(718 x 372mm)
Left Upright (DF635)
(125 x 356mm)
Right Side (DF633)
(718 x 372mm)
Right Upright (DF636)
(125 x 356mm)
Drawer Front (DF637)
(496 x 122mm)
Rail (DF640)
(503 x 78mm)
Drawer Base (T482-347)
(482 x 347mm)
Drawer Back (W471-95)
(471 x 95mm)
Left Drawer
Side (W350-95LH)
(350 x 95mm)
Right Drawer
Side (W350-95RH)
(350 x 95mm)
15
19
16 17
20 Stool Right
Drawer Side
(W300-124RH)
(300 x 124mm)
Stool Seat Pad (FHALPAD)
(458 x 300mm)
18
21 22 23
24 25
Stool
3
4
7
8
9
5
6
10
14
11 12 13
Dresser
Stool Left Side (DF342A)
(395 x 328mm)
Stool Base (DF347A)
(478 x 306mm)
Stool Right Side (DF343A)
(395 x 328mm)
Stool Top (DF344A)
(510 x 352mm)
Stool Drawer
Back (W445-124)
(445 x 124mm)
Modesty (DF634)
(966 x 244mm) x 2
Left Blanking Panel (DF638)
(242 x 125mm)
Right Blanking Panel (DF639)
(242 x 125mm)
Stool Rail (DF346A)
(478 x 160mm) x 2
Stool Drawer
Front (DF345B)
(495 x 157mm)
Stool Left
Drawer Side
(W300-124LH)
(300 x 124mm)
Stool Drawer Base (T456-297)
(456 x 297mm)

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Electric drill
(only use
when drilling
into walls)
B C
D E F
G
Small locking
nut (F3) x 4
I
A
Wooden dowel (F22) x 2 Metal dowel (F901) x 38
Large locking
nut (F900) x 34 Knock-in Peg (F171GY) x 8
M
Plastic Nail (F91) x 8
K
Wedgefix (F639) x 4
Mini block (F25) x 4
H
9mm Screw (F73) x 8
9mm Screw (F74) x 4 25mm Screw (F50) x 4
JL
JN
Handle (FBARHANDLE ) x 1
aL b
J
Drawer runner (F1004) x 4
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
19mm Screw (F461) x 2

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
B
B
B
C
C
CC
11 12
Step 2
Prepare the drawer
front
Screw 2 metal dowels
into the drawer front .
Note: Tighten the metal
dowels up fully against
the panels.
B
10
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
11
12
Attach the drawer
sides to the drawer
front
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
11
12
10
C
C
11
12
11
12
B
B
10
10

Assembly Instructions
5
Step 4
E
E
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
14
11 12
10
13
11 12
14
13
13
E
11 12
Step 7
Fit the wedgefixes
Turn the drawer
assemby over and slide
2 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
K
E
E
K
K
K
14
11
13
11
12
14
12
10
L b
L b
L a
Attach the handle
Attach the handle
to the drawer front
using 2 screws .
10
L a
L b
10

Finished
front edge
Assembly Instructions
6
Step 8
Prepare the left side
Screw 4 metal dowels
into the left side .
Note: Tighten the metal
dowels up fully against
the panels.
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Gently tap a mini block
into the left side ,
orientated as shown.
B
1
B
BD
D
D
FF
D
1
F
1
1
DD
B
B
F
F
Finished
front edge
Step 9
Prepare the right side
Screw 4 metal dowels
into the right side .
Insert 2 large locking
nuts into the right
side .
Gently tap a mini block
into the right side ,
orientated as shown.
B
2
D
2
Step 10
Prepare the 2
modesty panels
Insert 4 large locking
nuts into each of the
2 modesty panels .
D
8
F
2
2
D
D
D
D
8
B
B
B
B
x 2
Finished
edge

Fit the right side
Push the right side
into the 2 modesty
panels .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each modesty .
Finished
top edge
Assembly Instructions
7
Step 11
Shaped
edge
Join the 2 modesty
panels to the left side
Push the 2 modesty
panels onto the left
side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each modesty .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
D
D
8
8
1
D
8
2
8
Step 12
8
1
8
B
D
8
Note: Support this modesty
until the left side has been
fitted in the next step.
Important:
The finished edges on
the modesty panels must
be facing each other
8
2
1

Assembly Instructions
8
Step 13
Prepare the top
Screw 8 metal dowels
into the top .
Note: Tighten the metal
dowels up fully against
the panels.
B
BB
B
B
BB
B
B
7
Finished
front edge
H
J
Prepare the left upright
a: Place a runner on
the left upright as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left upright .
c: Screw a metal dowel
. into the left upright .
Insert 2 large locking
nuts into the left
upright .
Note: The arrow on the
locking nuts must point
towards the hole in the
edge of the panel.
Turn the left upright
over
d: Gently tap a mini
block into the left
upright , orientated as
shown.
3
H
H
D
3
3
J
J
B3
H
J
H
D
B
D
F
F
a:
b:
c:
d:
Turn the left
upright over
F
3
3
3
3
3

Finished
top edge
Assembly Instructions
9
Step 14
Shaped
edge
Prepare the right
upright
a: Place a runner on
the right upright as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right upright .
c: Screw a metal dowel
. into the right upright
. .
Insert 2 large locking
nuts into the right
upright .
Turn the right upright
over
d: Gently tap a mini
block into the left
upright , orientated as
shown.
4
H
H
D
4
4
J
J
B
4
a:
b:
c:
d:
Turn the right
upright over
F
4
Finished
front edge
H
J
H
J
H
D
D
B
F
F
4
4
4
4