Asoni CAM419 User manual

Mega-Pixel Network Vandal Dome
CAM419
User’s Manual
Version: 3.1
Date: 5/22/2008

1
Content
1. Preface .................................................................................................................................2
2. Product Specifications...........................................................................................................2
3. Product Installation ...............................................................................................................4
A. Hardware Installation.........................................................................................................4
B. Monitor Setting..................................................................................................................6
C. IPAssignment ...................................................................................................................7
D. Install ActiveX Control .......................................................................................................9
4. Live Video...........................................................................................................................11
5. Configuration ......................................................................................................................14
A. System............................................................................................................................14
B. Video/Audio Settings.......................................................................................................20
C. Network...........................................................................................................................25
D. Event Handling................................................................................................................29
6. Network Configuration ........................................................................................................37
Appendix....................................................................................................................................39

2
1. Preface
CAM419 Network Vandal Dome is a CMOS Network Vandal Dome. It builds in web server.
User views real-time video via IE browser.
CAM419 supports MPEG-4 & M-JPEG video compression which provides smooth and
high quality video. The video can be stored in the SD card, and can be playback remotely.
The PoE model built-in support for Power over Ethernet allows the camera to receive both
data and power over a single Ethernet cable.
2. Product Specifications
zMPEG-4 / MJPEG compression formats. Supports resolution up to SXGA(1280x1024),
1.3Mega pixels.
zMPEG-4 / MJPEG dual streaming.
zSelf-Contained HTTP Web Server providing Internet capability for remote access
zSupports SD card for local recording
z2-way audio
zUnbreakable housing
zSupport IP66 water proof standard
zBuilt-in support for Power over Ethernet (available for PoE models)
zOnline firmware upgrade
zReal-time video recording
zRecorded files compatible with Microsoft Windows Media Player

3
Hardware
CPU ARM 9 ,32 bit RISC
RAM 64MB
ROM 4MB
Image Sensor 1/4” CMOS, 1.3 Mega pixel
Digital I/O 1 In/ 1 Relay out (COM. & N.O.)
Audio In / Out 1 In / 1 Out
Power Consumption DC12V, 700mA PoE model: Built-In PoE (IEEE 802.3af)
Network
Ethernet 10/ 100 Base-T
Network Protocol HTTP, TCP/IP, RTP/RTSP, 3GPP, SMTP, FTP, PPPoE, DHCP, DDNS, NTP
System
Video Resolution 1280x1024, 640x480, 320x240, 160x120
Video Adjustment Brightness, Contrast, Exposure, Sharpness
Image Snapshot Yes
Full Screen Monitoring Yes
Compression Format MPEG-4, MJPEG
Dual Streaming Yes, MPEG-4 / MJPEG
Video BitrateAdjustment CBR, VBR
Motion Detection Yes, 3 different areas
Triggered Action Mail, FTP, Digital out, Save to SD card
Pre/ Post Alarm Yes, configurable
Security Password protection
Firmware Upgrade HTTP mode, can be upgraded remotely
Simultaneous Connection Up to 10
Audio Yes, 2-way
SD card management
Recording Trigger Motion detection, Digital input, IP check, Network break down
Video Format AVI, JPEG
Video Playback Yes
File Management Yes, can be deleted or overwrite
Web browsing requirement
OS Windows 2000, XP, 2003, Microsoft IE 6.0 or above
Hardware Suggested Intel-C 2.0G, RAM: 512MB, Graphic card: 64MB
Minimum Intel-C 1.6G, RAM: 256MB, Graphic card: 32MB

4
3. Product Installation
A. Hardware Installation
nPower Jack: To connect the included power adapter.
oDigital I/O: Digital In and Digital Out.
pAudio Input (Pink): The RCA connector allows connect to a microphone or audio
source, the connected audio will be heard at the remote site.
qAudio Output (Green): The RCA connector allows connect to an amplified speaker,
you can hear the voice of the remote site from the speaker.
rNetwork Connector: The RJ-45 connector allows connect the Ethernet cable.
1. Connect the cable of Digital I/O, Audio output and Audio input if you want to use these
functionalities.
2. Connect Ethernet cable for network connection.
3. Connect power adapter to turn on the camera.
4. If the camera is PoE model, the power adapter is not necessary. The camera will get
the power from the Ethernet cable. Please follow the below figure for the connection.
n
o
p
q
r
Power Jack (DC 12V)
Digital I/O
(Pink) Audio Input
(Green) Audio Output
Network Connector

5
5. Set up the network configurations according to the network environment. For further
explanation, please refer to chapter 6.

6
B. Monitor Setting
1. Right-Click on the desktop. Select [Properties]
2. Change color quality to “Highest (32bit)”.

7
C. IP Assignment
¾Always consult your network administrator before assigning an IP address to your
camera in order to avoid using a previously assigned IP address.
¾MAC Address: Each network camera has a unique Ethernet address (MAC address)
shown on the sticker of the camera.
¾One final note, although the IP Search is able to find and configure any network
camera on the LAN except those that are behind a router, it is a good idea to set the
host PC to the same subnet. In order to connect to the Web-based user interface of
the network camera, the host PC must be in the same subnet. For more information
about subnets, please consult your network administrator.
There are 3 kinds of IP configuration:
zFixed IP (Public IP or Virtual IP)
zDHCP (Dynamic IP)
zDial-up (PPPoE)
IP Search is a utility that provides an easier, more efficient way to configure the IP
address and network settings of the network camera. It even provides a convenient way
to set the network settings for multiple devices simultaneously. Moreover, IP Search can
save the network settings for all devices as a backup and restore them when necessary.
The software can be installed from the attached software CD.
1. Once IP Search has been successfully installed on the computer, double click the
IP Search icon on the desktop to run the software.

8
2. IP Search searches all the network devices which connect to the intranet and lists
on the window. Click [Search] button to search again.
3. From the list, select the device with the MAC Address that corresponds to the
device that is to be configured.
4. Click one of the network devices, the network configuration of this device will show
on the bottom.
5. After filling in the IPAddress, Subnet Mask, Gateway and the others, click [Set]
button to complete the configuration settings and save into the remote device.
6. You can assign a name to identify the camera. Type the name in “Device Name”
field, click [Save] and then click [Search] button, the name will be displayed in the
list.
7. Wait for 1 minute to let camera update the settings, and then click [Search] button
again to re-search the network devices. Click the network device listed on the
window and click [Open Web] button. It will open an IE browser and connect to this
device directly.

9
D. Install ActiveX Control
For the first time to view the camera video via IE, it will ask you to install the ActiveX
component.
If the installation failed, please check the security setting for the IE browser.
1. In IE, click on [Tools] Æ[Internet Options…]
2. Click on [Security] Tab Æ[Custom Level…]
3. In Security Settings, under [Download unsigned ActiveX controls], select “Enable”
or “Prompt”.
4. In Security Settings, under [Initialize and script ActiveX controls not marked as safe],
select “Enable” or “Prompt”.
5. When pop-up window with warning message, click [Yes] to save the settings.
1 2