Assa Abloy Lockwood 1220 Series User manual

P/No. 1220-321 - 0321
TURN KNOB MOUNTING INSTRUCTIONS
LOCKWOOD COMMERCIAL DOOR FURNITURE
B3570 SYNERGY SETTING AND HANDING
A3770 SELECTOR SETTING AND HANDING
SCREW REQUIRED TO SET FOR 3770 SELECTOR
SCREW REQUIRED TO SET HANDING
SET FOR LEFT HAND 3770 SET FOR RIGHT HAND 3770
45°
rotation
45°
rotation
ONE SCREW REQUIRED TO SET HANDING
SET FOR LEFT HAND 3570 SET FOR RIGHT HAND 3570
90°
rotation
90°
rotation
If mounting a disabled accessible turn, the escutcheon will need to be configured according to the mortice lock in use.
1. Refer to the images below to identify the mortice lock in use.
2. Position the screws according to the turn setting required.
Selector configurations should allow 45° rotation, Synergy configurations should rotate to 90°. Use images below as a guide.
1 Configuring Disabled Accessible Turn Escutcheon
SELECTOR MORTICE LOCK SYNERGY MORTICE LOCK
Stainless
steel plate
Narrow
auxiliary bolt
Wide
auxiliary bolt
Plain case
‘3570 Series’
‘3770 Series’
Turn knob Emergency
Turn
Disabled
Accessible Turn
Turn escutcheon examples: Tailbars for different turn escutcheon combinations:
P/No. TAILBAR-S1
Suits - 30-40mm doors
P/No. TAILBAR-E1
Suits 32-45mm doors
P/No. TAILBAR-S2
Suits - 40-50mm doors
Single side turn escutcheon only Privacy configuration
(Turn escutcheon both sides)
FOR THROUGH
FIX INSTALLATION
FOR THROUGH
FIX INSTALLATION
60mm BACKSET
89mm BACKSET
127mm BACKSET
60mm BACKSET
89mm BACKSET
127mm BACKSET
DRILL 2 HOLES
20mm DIA
FOR OVAL
CYLINDER ONLY
DRILL 2 HOLES
22mm DIA
FOR TURN
KNOB ONLY
DRILL
6.5mm DIA
DRILL
6.5mm DIA
FOLD ALONG THIS LINE AND
ALIGN TEMPLATE WITH EDGE OF DOOR
DRILL 2 HOLES
22mm DIA
FOR TURN
KNOB ONLY
DRILL 2 HOLES
20mm DIA
FOR OVAL
CYLINDER ONLY

TURN KNOB MOUNTING INSTRUCTIONS
LOCKWOOD COMMERCIAL DOOR FURNITURE
FOR THROUGH
FIX INSTALLATION
60mm BACKSET
89mm BACKSET
127mm BACKSET
DRILL 2 HOLES
20mm DIA
FOR OVAL
CYLINDER ONLY
DRILL 2 HOLES
22mm DIA
FOR TURN
KNOB ONLY
DRILL
6.5mm DIA
FOLD ALONG THIS LINE AND
FOR THROUGH
FIX INSTALLATION
60mm BACKSET
89mm BACKSET
127mm BACKSET
DRILL
6.5mm DIA
ALIGN TEMPLATE WITH EDGE OF DOOR
DRILL 2 HOLES
22mm DIA
FOR TURN
KNOB ONLY
2 Door Preparation
1. Cut out the template from the bottom of the sheet.
2. Remove lock from mortice and place the template in the correct
alignment according the the required backset.
3. Mark hole centres accurately and drill holes required.
4. For through fixing, cut screws to length. Deburr end of cut screws.
Note: Do not cut screws with pliers or side-cutters as this is likely
to cause thread damage upon assembly.
3 Mounting Instructions
Use the appropriate tailbar according to escutcheon combination being installed.
Follow instructions below for mounting each type of turn combination.
ASSA ABLOY Australia Pty Limited, 235 Huntingdale Rd, Oakleigh, VIC 3166 ABN 90 086 451 907 2021
Experience a safer and more open world
For single side turn escutcheon
P/No. TAILBAR-S1
Suits - 30-40mm doors
P/No. TAILBAR-S2
Suits - 40-50mm doors
1. Insert spring and tailbar into end of
turn knob as above. Push tailbar until
engaged and retained in turn knob.
Refer above for correct tailbar for your
door thickness.
2. Engage tailbar end into turn snib adaptor
as shown.
For privacy configuration (Turn escutcheon both sides)
P/No. TAILBAR-E1
Suits 32-45mm doors
1. Insert spring and narrow end
of tailbar into turn knob or
disabled accessible turn until
engaged and retained.
2. Pass tailbar completely through the turn
snib adaptor as shown.
3. Make sure tailbar engages with the turn
escutcheon on the other side of the lock.