Assa Abloy Corbin Russwin FE6600 Series User manual

FM467 03/20
Installation Instructions
Copyright © 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
WARNING
This product can expose you to lead
which is known to the state of California
to cause cancer and birth defects or other
reproductive harm. For more information
go to www.P65warnings.ca.gov.
FE6600 and
BL6600 Series
Freewheeling Lever with Escutcheon Trim
Multi-Point Lock

2
FE6600 and BL6600 Series
Installation Instructions
Multi-Point Lock
FM467 03/20
Copyright © 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
1 Tools Required
Phillips Screw Driver 3/8" Wrench 5/32" Allen Wrench
TOC Table of Contents
1 Tools Required ..................................................................2
2 Package Contents ...............................................................3
3 Installation ......................................................................4
a Install Lockbody .................................................................4
b Assemble Outside Escutcheon ...................................................4
c Assemble Adapter and Plate .....................................................4
d Secure Cylinder..................................................................5
e Inside Escutcheon ...............................................................5
f Inside Lever .....................................................................5
4 Changing Hand of Trim ..........................................................6

3
FE6600 and BL6600 Series
Installation Instructions
Multi-Point Lock
FM467 03/20
Copyright © 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
2 Package Contents
Figure1
1
11
12
3
4
2
5
6
14
13
9
8
C
AB
B10
D
7
Figure1 Description Qty.
1 Inside Lever 1
2 Spring 1
3 Set Screw 1
4 Thru-bolt Screws (1/4"-20 x 1-3/4) 2
5 Inside Escutcheon Plate 1
6 Screws & Lock Washers (#8-32 x 5/8") 2
7 Adapter & Plate Assembly 1
7A Adapter 1
7B Washers 2
7C Mounting Plate 1
7D Retaining Nut 1
8 Lever Spindle 1
9 Outside Escutcheon Assembly 1
10 Cylinder 1
11 Screws (#8-32 x 1/4") 2
12 Front Plate 1
13 Lockbody Screws (#12 x 1-1/4") 2
14 Lockbody 1

4
FE6600 and BL6600 Series
Installation Instructions
Multi-Point Lock
FM467 03/20
Copyright © 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
3 Installation
a Install Lockbody
Insert lock body into mortise cutout. Hold loosely in place with
(2) lock body screws.
Note:
Do not tighten screws fully at this time. (Figure2)
b Assemble Outside Escutcheon
1. With outside lever horizontal, carefully insert mounting
posts through the door and lock body.
• Make sure spindle is properly engaged in the lock.
• Outside escutcheon assembly should be flush with
door surface.
If cylinder is not included in this function, proceed to Step 3c.
2. Screw cylinder into lock body until flush with
escutcheon face. (Figure3)
c Assemble Adapter and Plate
1. Tighten retaining nut on inside of mounting plate and adapter as far
as it will go by hand, then back off retaining nut one notch until star
pattern lines up with square corners. (Figure4)
2. Insert lever spindle into adapter and plate assembly so that it is held in
place. (Figure5)
3. Insert inside adapter and plate assembly with lever spindle into square
hole on inside of door. (Figure6)
4. Now tighten two screws on the inside adapter
and plate assembly. Do not over tighten. (Figure7)
5. Tighten the lockbody screws. (Figure8)
Figure2
Figure3
Figure4
Figure5
Figure6
Figure7 Figure8

5
FE6600 and BL6600 Series
Installation Instructions
Multi-Point Lock
FM467 03/20
Copyright © 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
3 Installation (continued)
d Secure Cylinder
1. With the cylinder screwed flush into the
escutcheon face, check that the keyway is
vertical. This ensures that the cylinder retainer
fork will line up with the notch on the side of
the cylinder.
2. Tighten the cylinder retainer to secure the
cylinder.
3. Turn the key in the cylinder to make certain
that the lock functions correctly.
4. Secure the outside front plate to the lockbody.
(Figure9)
Figure9
e Inside Escutcheon
1. Place inside escutcheon flat against door. Align
thumb turn (if provided) with slot in lock body.
(Figure10)
2. Secure the inside escutcheon to the outside
escutcheon using thru-bolt screws provided.
(Figure11)
Figure10
Figure11

6
FE6600 and BL6600 Series
Installation Instructions
Multi-Point Lock
FM467 03/20
Copyright © 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
3 Installation (continued)
f Inside Lever
1. Place inside lever horizontally onto lever
spindle. Hold lever firmly against the
escutcheon. (Figure12)
2. Use the 1/8" Allen wrench to tighten the set
screw securely. Set screw should seat in the
groove of the inside adapter. (Figure13)
3. Pull on lever to test if set screw is properly
secured. (Figure14)
Figure12
Figure13
Adapter
Lever
Set Screw
Figure14

7
FE6600 and BL6600 Series
Installation Instructions
Multi-Point Lock
FM467 03/20
Copyright © 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
4 Changing Hand of Trim
Loosen screw (1) and remove interlocking assembly (2). (Figure15A)
Always wear eye protection while working.
1. Unscrew the lower thru-bolt stud (11) with a
3/8" wrench.
2. Remove mounting plate (6) and mounting
posts.
3. Switch mounting posts (7) so they occupy the
opposite positions on the mounting plate (6).
4. Note the original position of the extension
spring (16) and lower plate (9) in the
escutcheon (14). Unhook the extension spring
from pin (13).
5. Remove spring (16), lower plate (9) and
locking hub (8) assembly together.
6. Detach extension spring (16) from lower plate
(9) and locking hub assembly (8).
7. Flip lower plate on locking hub assembly
spindle so that the spring hole is on the
opposite side.
8. Reattach hook end of spring to lower plate.
9. Unscrew cap screw w/spacer (12) using a 5/32"
Allen wrench.
10.Move to opposite hole and tighten firmly.
11.Rotate lever to position shown in Figure16 for
desired hand.
12.Tighten retaining nut (10) firmly by hand and
then back off one notch until pattern shown in
Figure17 appears.
13.Attach bottom of spring (16) (closed loop) to
pin (13). Hold lever horizontal while inserting
locking hub assembly (8) and lower plate (9)
into retaining nut (10) escutcheon with lower
thru-bolt stud (11).
14.Refer to Figure16: Position hub (4) for required
function and hand, and ensure that spindle
(5) is vertical. Note position of interlocking
assembly hook when positioning hub.
Figure B
Figure15
Figure A
Interlocking
Assembly
Bottom
Hook
5
4
3
2
1
7
6
14 11
12 16
10
9
8
13
15
7
Functions
HubSpindle
Interlocking
Assembly Hook
24, 66 30
Figure16
Figure17

Corbin Russwin is a brand associated with ASSA ABLOY Access and Egress Hardware Group, Inc., an ASSA ABLOY Group company.
Copyright © 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Corbin Russwin, Inc.
225 Episcopal Road
Berlin, CT 06037 USA
Phone: [phone]
Fax: [phone]
www.corbinrusswin.com
FM467 03/20
4 Changing Hand of Trim (continued)
15.Reposition spindle as shown in Figure18 if necessary.
16.Place the interlocking assembly (2) into the escutcheon and attach the bottom hook to the locking
hub (8) as shown in Figure15B.
17.Secure in place with screw (1).
Caution:
Check that locking hub (4) moves freely by rotating the hub spindle
(5). If not, check that bottom hook is engaged in locking hub (8).
18.Insert and secure mounting plate and
mounting posts to escutcheon with
lower thru-bolt stud (11).
Figure18
Pull Out
Rotate and
Press In