Assa Abloy SARGENT 1331 User manual

Copyright © 2013 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing is prohibited. A8174A
63-8174-6000-999
Screw Pack
Regular Arm/Top
Jamb Shoe
Connecting Rod
Forearm
Screw
Main Arm
Closer Arm
Backcheck Valve Power Adjustment Shaft
Latch Valve
Sweep Valve
Closer Body
Cover
Insert
Insert Cutouts
1331 Series
Full Cover
Standard With
1331-C Cover
3/16"
#7
1/4-20
for Wood drill 7/32
Machine Screws
#7 Drill, 1/4-20 Tap
Metal Wood Self Drilling Screws
Wood and Metal
For Wood drill 3/16 hole
* Pilot Hole
Required
Sleeve Nut and Bolt
Thru Bolt and Grommet Nut
Drill 9/32 thru from Closer Side
3/8 Drill other side
Drill
3/8 Drill other Side
9/32 thru from Closer Side
(Optional)
Choose From 1 of 3 Applications
·Doors should be hung on ball bearing or anti-friction hinges.
·A separate door stop is recommended.
·Door and frame must be properly reinforced.
·Always adjust spring power before adjusting control.
·Adjust closing time speed between 3 and 7 seconds from 90° to 0°. Greater closing times may be required
ADA.
·These door closers should NOT be installed on the exposed side (weather side) of exterior doors
·NOTE: For special applications a separate door and frame preparation template is packed with these
instructions. Use this instruction sheet for installation sequence and closer adjustments only.
JO Arm (Regular Arm)
Right hand (RH) door shown.
Left hand reverse (LHR)
See page 2
JP9 Arm (Regular Arm)
Right hand (RH) door shown.
Left hand reverse (LHR)
See page 3
JO Arm (Top Jamb Arm)
Right hand (RH) door shown.
Left hand reverse (LHR)
See page 5
®
SARGENT 1331 DOOR CLOSER INSTALLATION
INSTRUCTIONS WITH FOLLOWING ARM SETS:
JO, JOZ and JP9
Strength Adjustment From Size 1 Through 6.
CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY
RESULT IN INJURY OR DAMAGE
FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477 or
www.Sargentlock.com
NOTE: These installation instructions to be used for
product manufactured on or after Nov. 1, 2013. Date
Code: KU and shipped with arms shown on
template pages. See page 6 for date code location.

— 2 —
Copyright © 2013 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing is prohibited. A8174A
63-8174-6000-999
Arm Placement in Shoe
(Adjust if needed)
or
or
7-1/2 % stronger
7-1/2 % weaker
-
+
A
F
90°
E
C
L
Y
S
Z
R
B
D
Clips for metal
covers 8500M
Installation Sequence 2
See page 6 for spring
and valve adjustments.
Opening
To 100°
101° to 130°
131° to *180°
7-1/2
(191)
6
(152)
4-1/2
(114)
Dimension "A"
Door/Wall/Hardware/Jamb
*
conditions permitting
5-1/2
(140)
1-3/4
(44)
12
(304.8)
1
(25.4)
A
1-3/8
(35)
3/4
(19)
Centerline
of Hinge
Frame Rabbet
Right Hand Shown
1
NOTE: These installation instructions to be used
for product manufactured on or after Nov. 1, 2013.
Date Code: KU Shipped with arm as shown.

Copyright © 2013 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing is prohibited. A8174A
63-8174-6000-999
— 3 —
Install Closer and Bracket
Continued next page.
D
Installation Sequence
A
B
E
C
1-1/2”
F
G
23
3-1/2
(89)
3/4
(19) 12
(304.8)
Top of
Door
Frame
Soffit B
C
L
19.1
1/2
(13)
7/16
(11)
2
(51)
2-3/4
(70) 3/8
(10)
A
Right Hand Shown
Door
Opening
To 120°
121° to 180°
*
A
9-1/2
(241)
7
(178)
B
3-3/4
(95)
1-1/4
(32)
Frame
Rabbet
1
Door/Wall/Hardware/Jamb
*
conditions permitting
NOTE: These installation instructions to be
used for product manufactured on or after
Nov. 1, 2013. Date Code: KU Shipped with
arm as shown.

— 4 —
Copyright © 2013 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing is prohibited. A8174A
63-8174-6000-999
Attach Arm With Proper Timing
Close Valves
Arm Screw
1-1/2
(38)
Assemble Arm
Open Valves
Caution:
Don't remove
valves
Latch
Sweep
!
L
Y
S
Z
R
L
Y
S
Z
R
Left Hand
Door
Right Hand
Door
or
B
A
Flat
Flat
R
o
t
a
t
e
Remove Arm
from Spindle
Place Arm on
Spindle
Preload Closer
Latch
Sweep
+
+
456
789
See page 6 for spring
and valve adjustments.

Right Hand Shown
— 5 —
Copyright © 2013 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing is prohibited. A8174A
63-8174-6000-999
Installation Sequence
D
A
B
C
L
Y
S
Z
R
E
90°
F
Clips for metal
covers 8500M
A
B
E
90°
or
or
7-1/2 % stronger
7-1/2 % weaker
-
+
Arm Placement in Shoe
(Adjust if needed)
2
See page 6 for spring
and valve adjustments.
Arm
Reveal
JO
To 3-0 (76)
JOZ
2-3/4 (70) to 6-3/4 (171.5)
12
(304.8)
A
3/4
(19)
1/2
(13)
5-1/2
(140)
1-7/8
(38)
1-3/4
(44) C
L
Frame
Rabbet
Door/Wall/Hardware/Jamb
*
conditions permitting
Opening
To 100°
101° to 130°
131° to *180°
7-1/2
(191)
6
(152)
4-1/2
(114)
Dimension "A"
Reveal
1
NOTE: These installation instructions to be used
for product manufactured on or after Nov. 1, 2013.
Date Code: KU Shipped with arm as shown.

— 6 —
CLOSED
70°
10°
Adjust Closing Speed Time to between 3 to 7 seconds
from 90°. Use of the door by handicapped, elderly or
small children may require greater closing time.
!2 Cover
Screws 5
Copyright © 2013 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing is prohibited. A8174A
63-8174-6000-999
Valve Adjustments
Sweep
+
-
Latch
+
-
Backcheck
+
-
4
Caution:
Don't completely
close valve
!
23
1
Adjustment Chart
EXTERIOR
INTERIOR
Regular Arm
Top Jamb
Regular Arm
Top Jamb
Parallel Arm
Parallel Arm
FULL 360° TURNS OF
5/16 POWER
ADJUSTMENT WRENCH
8100/8300/8500
DOOR
TYPE
OF
INST. *32"
(0.85M)
36"
(0.90M)
42"
(1.00M)
48"
(1.20M)
5811 13
7 10 13 16
710 13 16
912 15 18
20 FULL (360°) TURNS MAXIMUM AVAILABLE
*
MAXIMUM DOOR SIZE
Number of Turns Required
Closer is shipped set at mid range setting = 10 turns
The closing force is adjustable from a size 1 to a size 6, as
outlined in ANSI Standard A156.4. When these series of door
closers are installed and adjusted to conform to ADA reduced
opening force requirements (5 lbs max.) for interior doors, they
may not have adequate closing force to reliably close and latch
the door. Power adjustments charted on this page are
recommended where possible, to ensure proper door control.
By law the Americans with Disabilities
Act (ADA) may require that door
closer installation comply with
accessability guidelines.
!
Spring Power Adjust
+
-
Mfg.
Date: KU
KU