Assa Abloy Adams Rite 3700 User manual

1
3700/8700/8800
Rim Exit Device
Owner’s Manual

2
Table of Contents
Table of Contents...................................................................................2
What This Owner’s Manual Can Do For You.....................................3
Owner’s Record......................................................................................3
Exit Device Operation............................................................................4
Dogging the Push Bar...........................................................................5
Removing or Replacing the End Caps................................................6
Positioning the Jamb Strike..................................................................7
Maintenance............................................................................................8
Obtaining Replacement Parts and Service........................................8
Replacement Parts Available for 3700 RIM.......................................9
Replacement Parts Available for 8700 RIM.....................................10
Replacement Parts Available for 8800 RIM.....................................11
Troubleshooting....................................................................................12
Adams Rite Limited Warranty.............................................................12

3
What This Owner’s Manual Can Do For You
• It shows exactly how to operate your exit device.
• It shows you simple things to do and check before you call for service,
so you may save the cost of an
unnecessaryservicecall.
• It provides a complete listing of service replaceable parts.
•It contains your Adams Rite Limited Warranty and what steps to take
for service.
Owner’s Record
The model number is located on the hinge stile mounting base as shown
below. Refer to this number and the additional information below when
you call upon your local Adams Rite dealer regarding this product.
Model Number 3700/8700/8800
Finish ____________________
Door Size ____________________
Hardware Supplier ____________________
Date Installed ____________________

4
Exit Device Operation
Adams Rite rim mounted devices provide for life safety and security by us of a
“starwheel” bolt and interlocking strike. The device is totally different from
previous rim-mounted devices and achieves a new level of security for exit
devices without sacrificing life safety in any way. Additional security (against
jamb spreading) is achieved by a unique nose guard that interlocks with the
hardened steel strike plate.
When the push bar is depressed, an interior deadlocking slide is pulled back to
release the “starwheel” bolt allowing the door to open. Upon closing, the device
engages the strike and the deadlocking slide returns to secure the door. Exterior
entrance can be gained by key or with extensive line of entry trim available from
Adams Rite.

5
NOTE: The following is not applicable to 3700 devices.
Dogging the Push Bar
Dogging the push bar disables the latching function, making the door a simple
push/pull operation.
1. COMPLETE the following to dog the device.
a. DEPRESS the push bar completely and HOLD.
CAUTION
Over-rotation of the key past the prescribed ¼ turn can cause
damage to the Exit Device.
b. TURN the hex key 1/4 turn clockwise.
2. To release, TURN the hex key 1/4 turn counterclockwise.

6
Removing or Replacing the End Caps
NOTE: To facilitate maintenance procedures, the two end caps can be
removed.
1. PERFORM the following to remove the end caps.
a. INSERT a small Phillips tip screwdriver through the holes located in
the end caps and UNSCREW the concealed attachment screws.
b. REMOVE the end caps and SET aside.
2. PERFORM the following to replace the end caps.
a. LOCATE the end caps on the push bar.
NOTE: When replacing the end caps, the screws must be snapped in
the screw clips on the inside of the end caps.
b. ATTACH the end caps using a small Phillips tip screwdriver through
the holes located in the end caps and TIGHTEN the attachment
screws hand tight only.

7
Positioning the Jamb Strike
CAUTION
A proper frame stop must be used in conjunction with the door/exit device
or damage may occur.
NOTE: The jamb strike must be properly located and tightened securely for
the device to properly operate.
1. PERFORM the following to position the jamb strike.
a. POSITION the strike assembly so the “starwheel” bolt fully
interlocks around the strike when the door is closed.
b. LOOSEN the mounting screws, as necessary, to adjust the
horizontal positioning.
c. WHEN proper positioning is achieved,
THEN TIGHTEN the mounting screws securely.

8
Maintenance
Exit devices are designed for life safety first. Adams Rite devices are cycle
tested in excess of one million operations, both as prototypes during design and
as quality control samples periodically during production. Atmospheric and other
localized conditions vary greatly, but extremely dirty, salty or abrasive situations
could require service attention such as lubrication of moving parts from time to
time to assure reliability. Service personnel should be reminded that life safety is
the goal.
Other maintenance that might be required specifically for a Rim device includes:
• Tightening of jamb strike screws
• Tightening of push bar mounting screws
Obtaining Replacement Parts and Service
The merchandise that you have purchase has been carefully engineered and
manufactured under Adams Rite’s rigid quality standards and should provide
many years of satisfactory and dependable operation. However, like all
mechanical merchandise, it may require replacement parts or maintenance.
The Parts Manual is also available on Adams Rite’s web page at the following
address:
www.adamsrite.com

9
Replacement Parts Available for 3700 RIM
NOTE: The mounting bar final assembly is not available.

10
Replacement Parts Available for 8700 RIM
NOTE: The mounting bar final assembly is not available.