Assa Abloy Aperio KS100 User manual

Page 1 of 12
For more information visit website www.assaabloy.com/aperio P/N: 3080006.025_1
Product Specifications
Wireless Frequency: 2.4GHz, IEEE 802.15.4, using AES 128-bit encryption
Lock Battery Type: AA Lithium, 1.5 Volts (V)
Battery Life: 50,000 cycles*
Holding Force: 181 kg (400 lbs)
FCC Part 15 Compliant, Industry Canada Compliant
Operating Temperature: 0 to 50 °C (32 to 122 F)
HID® multiCLASS SE® technology Credentials Supported: High Frequency (13.56 MHz) –HID iCLASS,
HID iClass SE (SIO-enabled), HID iCLASS Seos, HID MIFARE SE, HID DESfire EV1 SE, MIFARE CLASSIC DESfire
EV1. Low Frequency (125KHz) –HID Prox, AWID, EM4102, ioProx. NFC on Android Mobile Phones.
AA Lithium Batteries required.
Use of other types of
batteries, such as alkaline, is
not supported and can result
malfunctions
2x
*All battery life claims are approximate and based on a set
configuration profile. Battery performance is based on pre-
defined system settings such as battery chemistry and battery
model used, credential presentation settings (LED/buzzer), UHF
polling period, UHF status intervals, and operations per
day. Actual battery performance will vary and depends on the
factors above.
AperioKS100
Wireless Cabinet Lock
Installation and Operating Instructions
xx May 2020

Page 2 of 12
For more information visit website www.assaabloy.com/aperio P/N: 3080006.025_1
Recommended tools
Cutting Wheel
Phillips #2 Screwdriver
Hardware Specifications
Table 1 –Cam
DPS (Door Position Sensor) Cable Extension
Optional –The DPS signal is closed when the handle is resting in its locked position. The DPS circuit can
be extended to include normally closed DPS switches arranged in a series to monitor additional doors
and panels
CAM
CAM LENGTH
CAM DEPTH
38mm - 4
(Standard)
38mm [1-1/2"]
26mm [1”]
38mm - 5
(Optional)
38mm [1-1/2”]
28mm
[1-1/10"]
45 mm - 1
(Optional)
45mm
[1-3/4”]
18mm
[7/10”]
DPS Extension Cable (Provided)
DPS
Switches:
As Needed
Optional
Switch #1
Extending the DPS Circuit:
A: Remove the DPS jumper
B: Connect the included DPS extension
cable
C: Connect additional normally closed
DPS switches as shown to monitor
additional panels.
Note: Normally closed DPS switch –closed when doors are closed
(Form A or SPST-NO), voltage free switch only

Page 3 of 12
For more information visit website www.assaabloy.com/aperio P/N: 3080006.025_1
Package Contents
Installing the Lock
Lock Body
Battery Bracket
Handle Assembly
with SFIC blank
plastic core
Handing Selectors
SFIC Cam and
Spacer
Cam
38mm - 4
2x AA Lithium
Batteries
Screw A
#1/4-20 x .50
Truss Head
Phillips
3x Screw B
8/32 x 5/16”
Pan Head
Phillips
Optional External DPS Cable
Harness
3x Dolphin
Connector
Note: SFIC mechanical key
override sold separately

Page 4 of 12
For more information visit website www.assaabloy.com/aperio P/N: 3080006.025_1
1. Locate the 150mm x 25mm lock cutout on the door. Connect battery cable
and optional DPS cable to lock body. Secure battery bracket to lockbody using 3x
screw B.
2. Ensure lock body is flush against the
mounting surface to depress tamper
switch.
3. Select appropriate handing selector.
4. Install handle, handing selector, and cam. Secure with screw A.
Tamper
Switch
Make sure that
it is pressed
correctly
when unit is
installed.
Failing to do
so could result
inoperational
unit locked on
the door.
Door Edge
Note: ensure that the arrow on the
handing selector is pointing
towards the edge of the door.
DPS Cable
(optional)

Page 5 of 12
For more information visit website www.assaabloy.com/aperio P/N: 3080006.025_1
Installing the SFIC Core (Optional)
1. Insert SFIC core and cam into handle. Use spacer for 6 pin SFIC core.
Note: SFIC blank plastic core (SFIC-BC)
sold separately. SFIC Blank is required if
no cylinder Is used.

Page 6 of 12
For more information visit website www.assaabloy.com/aperio P/N: 3080006.025_1
Installing the Batteries
1. Loosen screw on battery cover, slide cover down, and install batteries in the
appropriate orientation.
Micro USB Port
For emergency power & local (hard wired)
firmware updates, use micro USB port located on
the side of the KS100 reader.

Page 7 of 12
For more information visit website www.assaabloy.com/aperio P/N: 3080006.025_1
Optional Accessories
Part Number
Description
KS100-SFIC
MEDECO X4 7-pin SFIC cylinder & 2 keys
(1 Control,1 User)
KS100-SFIC-BC
KS SFIC blank, black plastic core
KS100-KS-CAM38
CAM: 38MM - 5 (28mm Depth)
KS100-KS-CAM45
CAM: 45MM - 1 (18mm Depth)
500-------35-00
ASSA ABLOY Aperio AH20 1:1 Wiegand Hub
500-------60-00
ASSA ABLOY Aperio AH20 Advanced Wiegand Hub
500ZB-EXTANT-00
ASSA ABLOY Aperio Hub External Antenna
500ZB-PAPUSB-00
ASSA ABLOY Aperio AP PAP Service Tool
500ZB-RD-USB-00
ASSA ABLOY Aperio USB Radio Dongle

Page 8 of 12
For more information visit website www.assaabloy.com/aperio P/N: 3080006.025_1

Page 9 of 12
For more information visit website www.assaabloy.com/aperio P/N: 3080006.025_1

Page 10 of 12
For more information visit website www.assaabloy.com/aperio P/N: 3080006.025_1

Page 11 of 12
For more information visit website www.assaabloy.com/aperio P/N: 3080006.025_1
WARNING
FCC Statement
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Operation with non-approved equipment is likely to result in interference to radio and TV reception. The
user is cautioned that changes and modifications made to the equipment without the approval of
manufacturer could void the user’s authority to operate this equipment.
IC Statement
This device complies with Industry Canada license-exempt RSS standards(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation.
Conformité aux normes FCC
Cet équipement a été testé et trouvé conforme aux limites pour un dispositif numérique de classe B,
conformément à la Partie 15 des règlements de la FCC. Ces limites sont conçues pour fournir une
protection raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet
équipement génère, utilise et peut émettre des fréquences radio et, s'il n'est pas installé et utilisé
conformément ment aux instructions du fabricant, peut causer des interferences nuisibles aux
communications radio. Rien ne garantit cependant que l'interférence ne se produira pas dans une
installation particulière. Si cet équipement provoque des interférences nuisibles à la réception radio ou de
télévision, qui peut être déterminé en comparant et en l'éteignant, l'utilisateur est encouragé à essayer de
corriger les interférence par une ou plusieurs des mesures suivantes:
1. Réorienter ou déplacer l'antenne de réception.
2. Augmenter la distance entre l'équipement et le récepteur.
3. Branchez l'appareil dans une prise sur un circuit différent de celui auquel le récepteur est connecté.
4. Consultez votre revendeur ou un technicien radio / TV pour assistance.Avertissement

Page 12 of 12
For more information visit website www.assaabloy.com/aperio P/N: 3080006.025_1
Les changements ou modififications à cet appareil sans expressément approuvée par la partie responsable
de conformité pourraient annuler l'autorité de l'utilisateur de faire fonctionner cet équipement.
Conformité aux normes IC
Cet appareil est confrome avec Industrie Canada exempt de license RSS standard(s).
Son fonctionnement est souimes aux deux conditions suivantes:
(1) cet appareil ne peut causer d’interférences, et
(2) cet appareil doit accepter toute interference, y compris des interférences qui peuvent provoquer un
fonctionnement indésirable du périphérique.
ASSA ABLOY Czech & Slovakia s.r.o.
[e-mail] | [phone]
Strojnická 633 | 516 01 Rychnov nad Kněžnou | Czech Republic