Assa Abloy Yale 8800 Series User manual

Installation Instructions
Copyright ©2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For technical support contact Yale®at 800.438.1951 x5033 or [email protected]
This product can expose you to
lead which is known to the state
of California to cause cancer and
birth defects or other reproductive
harm. For more information go to
www.P65warnings.ca.gov.
WARNING!
8800 Series Mortise Lock
Used with VN Escutcheon Trim and V Series
Indicators
80-8800-0017-000 12/20

Copyright ©2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For technical support contact Yale®at 800.438.1951 x5033 or [email protected]
2
8800 Series Mortise Lock
Installation Instructions
Used with VN Escutcheon Trim and V Series Indicators
80-8800-0017-000 12/20
1Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Indicator Variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Lock Set Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Rehanding Indicator (if required). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Prepare Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Install Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Install Outside Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Install Inside Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Install Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Install Outside Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Perform Functional Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Indicator Part List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3
2
4
TOC Table of Contents
5
1
2
3
6
7
1 Tools Required
#2 & #3 Phillips
head screwdrivers
Flat blade
screwdriver
1/8" Allen
Wrench 3/32" Drill bit T20 Torx Screw
with Tamper Pin
Driver
4
5
6

Copyright ©2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited
For technical support contact Yale®at 800.438.1951 x5033 or [email protected]
3
Installation Instructions
8800 Series Mortise Lock
80-8800-0017-000 12/20
Used with VN Escutcheon Trim and V Series Indicators
2 Indicator Variants
4 Rehanding Indicator (If required)
Depending on function and option ordered,
indicators are provided in the following
variations, these instructions detail how to install
with cylinder, however other variations follow
similar instructions. (Figure 1)
Contact factory for any questions.
Figure 1 Cylinder - For
installation
on inside or
outside of door.
Thumbturn -
For installation
on inside of
door.
Coin Turn - For
installation
on outside of
door.
No input / blank -
For installation on
inside or outside
of door.
3 Lock Set Configuration
To re-hand lock, see instructions on lock body.
LH
Left Hand
Hinges Left
Open Inward
RH
Right Hand
Hinges Right
Open Inward
LHRB
Left Hand
Reverse Bevel
Hinges Left
Open Outward
RHRB
Right Hand
Reverse Bevel
Hinges Right
Open Outward
Figure 2
Verify hand and bevel of door. (Figure 2) Spindle Cam Position for Locks with Deadbolt
(*includes 8864 function)
Outside Indicator Inside Indicator
Door Hand LH/LHRB
Spindle Cam Position for Locks without Deadbolt
(*does not include 8864 function)
Door Hand LH/LHRB
Figure 3
Note:
Stand on outside of locked door when determining door hand.
Next, verify inside and/or outside indicators are handed correctly,
using Spindle Cam Position chart. (Figure 3) If they are handed
correctly, skip to Step 5 “Prepare Door”.
If they are not handed correctly:
1. Remove indicator back plate by pulling out from top slot, then
remove spindle cam from assembly. (Figure 4)
2. Position spindle cam in correct direction for door hand.
(Figure 3)
Important:
• For thumbturn indicators, make sure thumbturn is positioned
in the 12 o’clock direction as shown. (Figure 5)
3. Slide spindle cam post into correct slot of display slide.
(Figure 4)
4. Re-seat back plate into original position.
5. Return indicator to the vacant/unlocked position for
installation.
Thumbturn
Position
Figure 4
Figure 5
Backing
Plate
Spindle cam
Door Hand RH/RHRB
Inside Indicator Outside Indicator
Inside Indicator Outside Indicator
Door Hand RH/RHRB
Outside Indicator Inside Indicator

Copyright ©2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For technical support contact Yale®at 800.438.1951 x5033 or [email protected]
4
8800 Series Mortise Lock
Installation Instructions
Used with VN Escutcheon Trim and V Series Indicators
80-8800-0017-000 12/20
5 Installation
1Prepare Door
Prepare door for function holes, size, and location
according to 7088-0005 door marker template, if not
already prepped.
Figure 6
Inside of door Outside
of door
RH door
shown
Lock
Lock
Screws
2Install Lock
1. Verify strike location according to
template. Clean out door pocket and
door edge of debris.
2. Make sure handing of lock matches
handing of door. Slide lock into door.
(Figure 6)
3. Temporarily hand tighten two (2)
lock screws (#12 x 1-1/4" wood
screws, or #12-24 x1/2" machine
screws).
NOTE: Keep door open until installation is complete.
3Install Outside Trim
Figure 7
1. Verify lock is in unlocked state (square control
hub slot should be oriented as a diamond).
2. Unscrew the inside spindle from the outside lever
assembly 1/2 turn and align the ramp in the hori-
zontal position before inserting into the lock.
3. Slide outside escutcheon assembly on door and
insert outside lever assembly and plastic bushing
into lock body. Lever must be horizontal. (See
Figure 7)
NOTE: If indicator is used on outside, align indicator
spindle with control hub.
Outside Escutcheon
Assembly
Outside Lever
Assembly
Plastic Bushing

Copyright ©2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited
For technical support contact Yale®at 800.438.1951 x5033 or [email protected]
5
Installation Instructions
8800 Series Mortise Lock
80-8800-0017-000 12/20
Used with VN Escutcheon Trim and V Series Indicators
5 Installation, continued
4Install Inside Trim
1. Verify lock is in unlocked state
(turn outside lever to ensure).
2. Align inside escutcheon assembly
and install onto inside door face.
(Figure 8)
3. Note: If indicator is used on
inside, align indicator spindle with
control hub.
4. Through-bolt inside escutcheon
to outside escutcheon with two
(2) #8-32 x 2-1/4" screws.
Figure 8
Inside Escutcheon Assembly
#8-32 x 2-1/4" screw
#8-32
x 2-1/4"
screw
Set
screw
Plastic
Bushing
Inside
Lever

Copyright ©2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For technical support contact Yale®at 800.438.1951 x5033 or [email protected]
6
8800 Series Mortise Lock
Installation Instructions
Used with VN Escutcheon Trim and V Series Indicators
80-8800-0017-000 12/20
5 Installation, continued
7Install Cylinder
Figure 9
Figure 10
Figure 11
1. Thread cylinder into lock until flush with escutch-
eon surface. (Figure 9)
• Pull key slightly out of cylinder to help thread into
lock body.
2. Tighten cylinder clamp screw with #2 Phillips
screwdriver.
• Check operation and adjust if necessary.
Notes:
• Yale logo must be horizontal and on top. (See
Figure 10.)
• If double cylinder function is used, repeat steps 7.1
and 7.2 for second cylinder.
• Interchangeable Core cylinders require a control
key to remove and install the core. This is not pro-
vided standard. It must be requested seperately.
Cylinder
Cylinder
Clamp
Screw
Key and cylinder must be rotated as shown.
8Install Outside Front
1. Tighten the two (2) lock screws completely:
(Figure 11)
2. Attach outside front with two (2) flat head screws
#8-32 x 1/4".
9Perform Functional Check
DO NOT FORCE if resistance is encountered during
functional check. Refer back to Rehanding Indicator (if
required) section to ensure correct handing. Rehand if
necessary.
1. Insert key into cylinder (if present) and rotate:
• Ensure there is no friction against lock case or any
other obstructions.
2. Check key retracts latch:
• Key should rotate freely.
3. Throw deadbolt (if present):
• Check key retracts both deadbolt and latch.
4. Test levers:
• Confirm latch and deadbolt (if installed) retract.
5. Verify indicator displays correct status when
locked and unlocked.
Correct Incorrect
Lock Screw
Outside
Front
#832
x 1/4"
Screws
Lock Screw

Copyright ©2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited
For technical support contact Yale®at 800.438.1951 x5033 or [email protected]
7
Installation Instructions
8800 Series Mortise Lock
80-8800-0017-000 12/20
Used with VN Escutcheon Trim and V Series Indicators
6 Indicator Parts List
Figure 12
#Description Part # Req.
1 VN Indicator Escutcheon Consult Factory 1
2 Indicator Window 856F049 1
3
Indicator Display Assembly - Green Unlocked / Red Locked 82-5602-4000
1
Indicator Display Assembly - Green Vacant / Red Occupied 82-5603-4000
Indicator Display Assembly - Green Unlocked Icon / Red
Locked Icon
82-5604-4000
Indicator Display Assembly - White Unlocked / Red Locked 82-5605-4000
Indicator Display Assembly - White Vacant / Red Occupied 82-5606-4000
Indicator Display Assembly - White Unlocked Icon / Red
Locked Icon
82-5607-4000
Indicator Display Assembly - Green Ouvert / Red Fermé 82-5684-4000
Indicator Display Assembly - Green Libre / Red Occupée 82-5685-4000
4A Indicator Spindle Cam - Thumbturn 50-8800-9328
1
4B Indicator Spindle Cam - Cylinder/No Input 50-8800-7335*
4C Indicator Spindle Cam - Cylinder Overtravel 50-8800-0378*
4D Indicator Spindle Cam - Thumbturn Overtravel 50-8800-0346
4E Indicator Spindle Cam - Coin Turn 50-8800-7339*
5 Indicator Backing Plate 855F638 1
6 VN Escutcheon Screw Pack (Not shown) 858F517 FIN* 1
7 Field Prep Marker Template (Not shown) 7088-1008 1
*These parts are for 1-3/4" standard thickness doors. For other thicknesses, contact the factory.
NOTE: Reference 8800 Series parts manual for all lock body parts.
5
4
3
2
1
4A
4B
4C
4D
4E

80-8800-0017-000 12/20
THE YALE BRAND, with its unparalleled global reach and
range of products, reassures more people in more countries
than any other consumer locking solution.
THE ASSA ABLOY GROUP is the world´s leading
manufacturer and supplier of locking solutions, dedicated to
satisfying end-user needs for security, safety and convenience.
Yale Commercial is a business associated with ASSA ABLOY Access and Egress
Hardware Group, Inc., an ASSA ABLOY Group company. Copyright © 2020,
ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved.
Reproduction in whole or in part without the express written permission of
ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited. Patent
pending and/or patent www.assaabloydss.com/patents.
U.S.A.
Yale Locks & Hardware
Address: 225 Episcopal Road
Berlin, CT 060374004
Tel: 18004381951
Fax: 18003380965
yalecommercial.com
Canada:
ASSA ABLOY Door Security Solutions Canada
Address: 160 Four Valley Drive
Vaughan, Ontario L4K 4T9
Tel: 18004613007
Fax: 18004618989
assaabloydss.ca
International:
ASSA ABLOY Americas International
Tel: 19058217775
Fax: 19058211429
assaabloyai.com
Contact Us
Customer Service Phone:
1-800-438-1951
Customer Service Fax:
1-800-338-0965
Technical Product Support:
[e-mail]
Customer Service:
[e-mail]
Website:
Yalecommercial.com
Email for orders:
[e-mail]
Trusted every day
Part of ASSA ABLOY