AT&T BE50 User manual

1year
warranty
www.att.com/electronics
© 2019 Concept 101 LLC. All Rights Reserved. AT&T and the AT&T
logo are trademarks of AT&T Intellectual Property licensed to
Concept 101 LLC, New York, New York 10018. Printed in China.
Issue 1.0 AT&T 2/11/2019.
The AT&T brands are used under license.
Any repair, replacement, or warranty
service, and all questions about this product
should be directed to Concept 101 LLC at
www.att.com/electronics or call 1(888)
920-8680 from the USA or Canada. Concept
101 LLC warrants that the product will be free from defects in
material, parts and workmanship for the period of one (1) year
from date of purchase. Concept 101 LLC agrees that it will, at its
option, replace the defective product with either a new or
remanufactured product equivalent to your original purchase
during the warranty period. Please be advised the returned
product must carry the proof of purchase.
Concept 101 LLC does not warrant that the product will work
properly in all environmental conditions, and makes no warranty
and representation, either implied or expressed, with respect to
the quality, performance, merchantability, or fitness for a
particular purpose other than the purpose identified within this
user’s manual. Concept 101 LLC has made every effort to ensure
that this user’s manual is accurate and disclaims liability for any
inaccuracies or omissions that may have occurred. Information in
this user’s manual is subject to change without notice and does
not represent a commitment on the part of Concept 101 LLC.
Concept 101 LLC reserves the right to make improvements to this
user’s manual and/or to the products described in this user’s
manual at any time without notice. If you find information in this
manual that is incorrect, misleading, or incomplete, please
contact us through our website.
CONTROLS
BE10
Wireless Earbuds
Thank You For Purchasing
SBE7 Wireless Sports Earbuds
User’s Guide
BUTTON FUNCTIONS
Phone button
· When playing music, press and release to pause
music; press and release again to play music.
· When receiving an incoming call, press and release
to answer; press and release to end the call.
· Press twice quickly to call the last number
dialed. When playing music and a call comes in,
the music will pause and you will hear a
ringtone. The music will resume when the call
is ended.
Volume up/track forward
· Press to increase the volume.
· Press and hold to play next track.
Volume down/track back
· Press to decrease the volume.
· Press and hold to play previous track.
The button functions may vary per device.
CHARGING YOUR BE10
Make sure your BE10 is fully charged before
using it for the first time.
· Gently plug the Micro USB end of the included
charging cable into the charge port of the
control box.
· Plug the USB end of the cable into a powered
USB port, such as a computer, laptop, or a USB
AC adapter (not included).
· The LED indicator located on the control box
will glow red. Once the headset is fully charged,
the LED power indicator will turn off.
· The LED indicator will light up red while
charging even if the BE10 is off. You cannot
charge your BE10 while listening to music.
CONNECTING YOUR DEVICE
Adjust the volume of your device and the BE10 to
a comfortable volume before use.
· Press and hold the power button for a few
seconds and the unit will enter into pairing mode.
· Open the settings on your Bluetooth device
(Bluetooth must be enabled).
· Select “BE10” from the list of Bluetooth devices.
· Once paired, the LED indicator light will flash
blue slowly.
· To turn off the BE10, prss and hold the power
button.
For any questions or support please visit
www. att.com/electronics and click on the
Support tab.
LED light
Red Light ON
Charging
Blue Light ON
Fully Charged
Power/Multi-functional
ON/OFF, Call Answer
Hang Up / Refuse
Play/ Pause
Volume down/
Track back
Volume up/
Track forward
These earbuds have an internal rechargeable battery. The battery
must be fully charged prior to use. Charging time is approximately
1hr. Your earbuds cannot be used while charging.
80 mm
80 mm
153 mm
Tri-Fold
BE50 USER’S MANUAL
Size: 153 X 80 mm (when folded 51 X 80 mm)
Printed on both sides (white uncoated paper, 100g)
Side A
Side B

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operation in conjunction with any other
antenna or transmitter.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. in portable exposure
condition without restriction.